Problem Symptoms Table [09/2012 - ]
NOTE:
Before replacing the certification ECU, refer to Registration. Refer to REGISTRATION [09/2012 - ] .
HINT:
- Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.
- Inspect the fuses and relays related to this system before inspecting the suspected areas below.
METER GAUGE
| Symptom | Suspected Area | Refer to |
|---|---|---|
| Speedometer malfunction | Speedometer circuit | Refer to Speedometer Malfunction |
| Tachometer malfunction | Tachometer circuit | Refer to Tachometer Malfunction |
| Engine coolant temperature receiver gauge malfunction | Engine coolant temperature receiver gauge circuit | Refer to Engine Coolant Temperature Gauge Malfunction |
WARNING LIGHT OR INDICATOR LIGHT
| Symptom | Suspected Area | Refer to |
|---|---|---|
| Turn indicator light does not come on (Turn signal light operates normally) | No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] |
| Front fog indicator light does not come on (Front fog light operates normally) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Perform Active Test (Indicat. Lamp Fr FOG) | Refer to DATA LIST / ACTIVE TEST [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Main body ECU (driver side junction block) | - | |
| High beam indicator light does not come on (High beam headlight operates normally) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Perform Active Test (Indicat. Lamp Beam) | Refer to DATA LIST / ACTIVE TEST [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Main body ECU (driver side junction block) | - | |
| Headlight indicator light does not come on (Headlight operates normally) (for U.S.A.) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Perform Active Test (Indicat. Lamp Head) | Refer to DATA LIST / ACTIVE TEST [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Main body ECU (driver side junction block) | - | |
| Taillight indicator light does not come on (Taillight operates normally) (except U.S.A.) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Perform Active Test (Indicat. Lamp Tail) | Refer to DATA LIST / ACTIVE TEST [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Main body ECU (driver side junction block) | - | |
| Open door warning light does not come on (Courtesy light switch operates normally) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Perform Active Test (Indicat. Lamp Doors All Open) | Refer to DATA LIST / ACTIVE TEST [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Main body ECU (driver side junction block) | - | |
| Front seat belt warning light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Perform Active Test (Driver Side Seat Belt or Front Passenger Side Seat Belt) | Refer to DATA LIST / ACTIVE TEST [09/2012 - ] | |
| Seat belt warning system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| SRS warning light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Check indicator/warning light | Refer to OPERATION CHECK [09/2012 - ] | |
| Perform Active Test (Indicat. Lamp Airbag) | Refer to DATA LIST / ACTIVE TEST [09/2012 - ] | |
| Airbag system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Master warning light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Check indicator/warning light | Refer to OPERATION CHECK [09/2012 - ] | |
| Perform Active Test (Master Warning) | Refer to DATA LIST / ACTIVE TEST [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| MIL does not come on | Check indicator/warning light | Refer to OPERATION CHECK [09/2012 - ] |
| SFI system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Charge warning light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Check indicator/warning light | Refer to OPERATION CHECK [09/2012 - ] | |
| Perform Active Test (Indicat. Lamp Charge) | Refer to DATA LIST / ACTIVE TEST [09/2012 - ] | |
| Read the Data List (Alt L Signal) | Refer to DATA LIST / ACTIVE TEST [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Front multiplex network light ECU (front controller) | - | |
| EPS warning light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Check indicator/warning light | Refer to OPERATION CHECK [09/2012 - ] | |
| Perform Active Test (Indicat. EPS) | Refer to DATA LIST / ACTIVE TEST [09/2012 - ] | |
| Power steering system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Brake warning light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Check indicator/warning light | Refer to OPERATION CHECK [09/2012 - ] | |
| Perform Active Test (Indicat. Lamp Brake or Indicat. Lamp ECB*) | Refer to DATA LIST / ACTIVE TEST [09/2012 - ] | |
| Electronically controlled brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Parking brake warning light does not come on | Check indicator/warning light | Refer to OPERATION CHECK [09/2012 - ] |
| Perform Active Test (Indicat. Park) | Refer to DATA LIST / ACTIVE TEST [09/2012 - ] | |
| Harness or connector | - | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Electric parking brake ECU | Refer to REMOVAL [09/2012 - ] | |
| Cruise control indicator light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Perform Active Test (Indicat. Lamp Cruise) | Refer to DATA LIST / ACTIVE TEST [09/2012 - ] | |
| Cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Radar cruise indicator light does not come on (w/ Dynamic Radar Cruise Control System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Perform Active Test (Indicat. Radar Cruise) | Refer to DATA LIST / ACTIVE TEST [09/2012 - ] | |
| Dynamic radar cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| SET indicator light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Perform Active Test (Indicat. SET) | Refer to DATA LIST / ACTIVE TEST [09/2012 - ] | |
| Cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| Dynamic radar cruise control system (w/ Dynamic Radar Cruise Control System) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Fuel level warning light does not come on (Fuel receiver gauge operates normally) | Perform Active Test (Indicat. Lamp Fuel) | Refer to DATA LIST / ACTIVE TEST [09/2012 - ] |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| ABS warning light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Check indicator/warning light | Refer to OPERATION CHECK [09/2012 - ] | |
| Perform Active Test (Indicat. Lamp ABS) | Refer to DATA LIST / ACTIVE TEST [09/2012 - ] | |
| Electronically controlled brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Slip indicator light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Check indicator/warning light | Refer to OPERATION CHECK [09/2012 - ] | |
| Perform Active Test (Indicat. Lamp Slip) | Refer to DATA LIST / ACTIVE TEST [09/2012 - ] | |
| Electronically controlled brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| VSC OFF indicator light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Check indicator/warning light | Refer to OPERATION CHECK [09/2012 - ] | |
| Perform Active Test (Indicat. VSC OFF) | Refer to DATA LIST / ACTIVE TEST [09/2012 - ] | |
| Electronically controlled brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| PCS warning light does not come on (w/ Pre-collision System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Check indicator/warning light | Refer to OPERATION CHECK [09/2012 - ] | |
| Perform Active Test (Indicat. Precrash) | Refer to DATA LIST / ACTIVE TEST [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Driving support ECU | Refer to REMOVAL [09/2012 - ] | |
| LKA indicator light does not come on (w/ Lane-keeping Assist System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Perform Active Test (Drift From The Lane) | Refer to DATA LIST / ACTIVE TEST [09/2012 - ] | |
| Lane-keeping assist system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Tire pressure warning light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Check indicator/warning light | Refer to OPERATION CHECK [09/2012 - ] | |
| Perform Active Test (Indicat. Tire Pressure Warning System) | Refer to DATA LIST / ACTIVE TEST [09/2012 - ] | |
| Tire pressure warning system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| SNOW indicator light does not come on (Automatic transmission system operates normally) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Perform Active Test (Indicat. Lamp ECT SNOW) | Refer to DATA LIST / ACTIVE TEST [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| TCM (for AA80E) | Refer to REMOVAL [09/2012 - ] | |
| TCM (for AA80F) | Refer to REMOVAL [09/2012 - ] | |
| HEIGHT HIGH indicator light does not come on (w/ Air Suspension System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Check indicator/warning light | Refer to OPERATION CHECK [09/2012 - ] | |
| Perform Active Test (Indicat. Height High) | Refer to DATA LIST / ACTIVE TEST [09/2012 - ] | |
| Air suspension system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Brake holding standby indicator light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Check indicator/warning light | Refer to OPERATION CHECK [09/2012 - ] | |
| Perform Active Test (Indicat. Brake Hold) | Refer to DATA LIST / ACTIVE TEST [09/2012 - ] | |
| Electronically controlled brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Brake hold operated indicator light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Check indicator/warning light | Refer to OPERATION CHECK [09/2012 - ] | |
| Perform Active Test (Indicat. Hold) | Refer to DATA LIST / ACTIVE TEST [09/2012 - ] | |
| Electronically controlled brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Automatic high beam indicator light does not come on (Automatic high beam system operates normally) (w/ Automatic High Beam System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Perform Active Test (Automatic High Beam Indicator) | Refer to DATA LIST / ACTIVE TEST [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Main body ECU (driver side junction block) | - |
- ECB*: Electronically Controlled Brake System
MULTI-INFORMATION DISPLAY
| Symptom | Suspected Area | Refer to |
|---|---|---|
| Cruising range display malfunction (Combination meter operates normally) | No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] |
| Average fuel consumption display malfunction (Combination meter operates normally) | No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] |
| Current fuel consumption display malfunction (Combination meter operates normally) | No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] |
| Average fuel consumption after refueling display malfunction (Combination meter operates normally) | No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] |
| Driving distance after refueling display malfunction (Combination meter operates normally) | No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] |
| Elapsed time display malfunction (Combination meter operates normally) | No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] |
| Average vehicle speed display malfunction (Combination meter operates normally) | No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] |
| ODO/TRIP meter display malfunction (Combination meter operates normally) | No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] |
| Outside temperature display malfunction | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Air conditioning system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Air conditioning amplifier | Refer to REMOVAL [09/2012 - ] | |
| Shift position indicator malfunction | Perform Active Test (A/T Indicator Operation 1, A/T Indicator Operation 2, A/T Indicator Operation 3) | Refer to DATA LIST / ACTIVE TEST [09/2012 - ] |
| CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| Automatic transmission system (AA80E) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| Automatic transmission system (AA80F) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| TCM (for AA80E) | Refer to REMOVAL [09/2012 - ] | |
| TCM (for AA80F) | Refer to REMOVAL [09/2012 - ] | |
| Rheostat display malfunction | Read the Data List (Light Control Up Switch, Light Control Down Switch) | Refer to DATA LIST / ACTIVE TEST [09/2012 - ] |
| Light control rheostat | Refer to INSPECTION [09/2012 - ] | |
| Harness or connector | - | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Eco driving indicator zone display malfunction | Check customize setting | Refer to CUSTOMIZE PARAMETERS [09/2012 - ] |
| CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| SFI system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| ECM | Refer to REMOVAL [09/2012 - ] | |
| Tire pressure display malfunction | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Tire pressure warning system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Tire pressure warning ECU | Refer to REMOVAL [09/2012 - ] | |
| Clearance warning display malfunction (w/ Intuitive Parking Assist System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Intuitive parking assist system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Clearance warning ECU | Refer to REMOVAL [09/2012 - ] | |
| Open door message display malfunction (Others system operates normally) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Main body ECU (driver side junction block) | - | |
| Front multiplex network light ECU (front controller) | - | |
| Luggage closer motor assembly (w/ Power Trunk Lid System) | Refer to REMOVAL [09/2012 - ] | |
| Luggage room junction block (rear junction block ECU) (w/o Power Trunk Lid System) | - | |
| DTCs display malfunction (Others system operates normally) | No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] |
| "Shift to P range" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Smart access system with push-button start (for Start Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Certification ECU | Refer to REMOVAL [09/2012 - ] | |
| "Low Key Battery" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Smart access system with push-button start (for Entry Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Certification ECU | Refer to REMOVAL [09/2012 - ] | |
| "Key is not detected" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Smart access system with push-button start (for Start Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Certification ECU | Refer to REMOVAL [09/2012 - ] | |
| "Depress the brake pedal, and touch the engine switch with the key" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Smart access system with push-button start (for Start Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Certification ECU | Refer to REMOVAL [09/2012 - ] | |
| "To start depress the brake pedal, and push the engine switch " message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Smart access system with push-button start (for Start Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Certification ECU | Refer to REMOVAL [09/2012 - ] | |
| "Theft Sensor OFF" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Theft deterrent system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Main body ECU (driver side junction block) | - | |
| "Theft Sensor ON" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Theft deterrent system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Main body ECU (driver side junction block) | - | |
| "Check Steering Lock System" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Steering lock system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Certification ECU | Refer to REMOVAL [09/2012 - ] | |
| "Steering Lock is still active" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Steering lock system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Certification ECU | Refer to REMOVAL [09/2012 - ] | |
| "Check Headlight System" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Lighting system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Headlight swivel ECU assembly | Refer to REMOVAL [09/2012 - ] | |
| Main body ECU (driver side junction block) (for LED Headlight, w/ Automatic High Beam System) | - | |
| "Check Rear Light System" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Lighting system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Luggage room junction block (rear junction block ECU) | - | |
| "Low Washer Fluid" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Wiper and washer system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Front multiplex network light ECU (front controller) | - | |
| "Turn Light Off" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Lighting system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Main body ECU (driver side junction block) | - | |
| "Moon Roof Opened" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Sliding Roof) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Siding roof system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Main body ECU (driver side junction block) | - | |
| "Turn on the high beam to activate AHB System" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Automatic High Beam System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Lighting system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Main body ECU (driver side junction block) | - | |
| "Change the Air Conditioning Filter" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Air conditioning system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Air conditioning amplifier | Refer to REMOVAL [09/2012 - ] | |
| "Air Conditioning Filter Reset" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Air conditioning system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Air conditioning amplifier | Refer to REMOVAL [09/2012 - ] | |
| "Check SRS Airbag System" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Airbag system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Center airbag sensor | Refer to REMOVAL [09/2012 - ] | |
| "Low Engine Oil Level" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Read the Data List (Oil Level SW) | Refer to DATA LIST / ACTIVE TEST [09/2012 - ] | |
| Harness or connector | - | |
| Engine oil level sensor (for 2WD) | Refer to INSPECTION [09/2012 - ] | |
| Engine oil level sensor (for AWD) | Refer to INSPECTION [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Front multiplex network light ECU (front controller) | - | |
| "Low Oil pressure" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Harness or connector | - | |
| Engine oil pressure switch | Refer to REMOVAL [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Front multiplex network light ECU (front controller) | - | |
| "Check engine system" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| SFI system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| ECM | Refer to REMOVAL [09/2012 - ] | |
| "Injector Maintenance Required" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| SFI system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| ECM | Refer to REMOVAL [09/2012 - ] | |
| "Resetting Maintenance Data" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| SFI system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| ECM | Refer to REMOVAL [09/2012 - ] | |
| "Maintenance required soon" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| SFI system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| ECM | Refer to REMOVAL [09/2012 - ] | |
| "Maintenance required" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| SFI system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| ECM | Refer to REMOVAL [09/2012 - ] | |
| "Check Generator" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Electric power control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Electric power control ECU | - | |
| "Low Battery" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Electric power control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Electric power control ECU | - | |
| "Electrical equipment operation is limited" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Electric power control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Electric power control ECU | - | |
| "Check Power Control System" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Electric power control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Electric power control ECU | - | |
| "Low Tire Pressure Check all tires" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Tire pressure warning system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Tire pressure warning ECU | Refer to REMOVAL [09/2012 - ] | |
| "Tire Pressure Reset Proceeding" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Tire pressure warning system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Tire pressure warning ECU | Refer to REMOVAL [09/2012 - ] | |
| "Tire Pressure Test Mode" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Tire pressure warning system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Tire pressure warning ECU | Refer to REMOVAL [09/2012 - ] | |
| "Check Air Suspension System" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Air Suspension System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Air suspension system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Suspension control ECU | Refer to REMOVAL [09/2012 - ] | |
| "Check Power Steering System" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Power steering system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Power steering ECU | Refer to REMOVAL [09/2012 - ] | |
| "Check VGRS System" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Variable Gear Ratio Steering System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Variable gear ratio steering system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Steering control ECU | Refer to REMOVAL [09/2012 - ] | |
| "VGRS Test Mode" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Variable Gear Ratio Steering System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Variable gear ratio steering system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Steering control ECU | Refer to REMOVAL [09/2012 - ] | |
| "Brake Malfunction" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (Electronically controlled brake system operates normally) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Skid control ECU | Refer to REMOVAL [09/2012 - ] | |
| "Check ABS" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Electronically controlled brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Skid control ECU | Refer to REMOVAL [09/2012 - ] | |
| "Check Brake System" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Electronically controlled brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Skid control ECU | Refer to REMOVAL [09/2012 - ] | |
| "Brake Hold not available on slope" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Electronically controlled brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Skid control ECU | Refer to REMOVAL [09/2012 - ] | |
| "Depress the brake pedal to release Brake Hold" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Electronically controlled brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Skid control ECU | Refer to REMOVAL [09/2012 - ] | |
| "Check Brake Hold System" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Electronically controlled brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Skid control ECU | Refer to REMOVAL [09/2012 - ] | |
| "EPB* TEST" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Electric parking brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Electric parking brake ECU | Refer to REMOVAL [09/2012 - ] | |
| "Parking Brake not available" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Electric parking brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Electric parking brake ECU | Refer to REMOVAL [09/2012 - ] | |
| "Check Parking Brake System" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Electric parking brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Electric parking brake ECU | Refer to REMOVAL [09/2012 - ] | |
| "Parking Brake Overheat" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Electric parking brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Electric parking brake ECU | Refer to REMOVAL [09/2012 - ] | |
| "To park the vehicle, shift to P range" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Electric parking brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Electric parking brake ECU | Refer to REMOVAL [09/2012 - ] | |
| "Release the Parking Brake" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (Parking brake warning light operates normally) | No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] |
| "The Parking Brake has been automatically locked" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Electric parking brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Electric parking brake ECU | Refer to REMOVAL [09/2012 - ] | |
| "Brake Pad Wear" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Electronically controlled brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Skid control ECU | Refer to REMOVAL [09/2012 - ] | |
| "Depress the brake pedal" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Electronically controlled brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Skid control ECU | Refer to REMOVAL [09/2012 - ] | |
| "Be careful using Brake Hold on icy roads!" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Electronically controlled brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Skid control ECU | Refer to REMOVAL [09/2012 - ] | |
| "Close the door to use Brake Hold" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Electronically controlled brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Skid control ECU | Refer to REMOVAL [09/2012 - ] | |
| "Fasten the seat belt to use Brake Hold" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Electronically controlled brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Skid control ECU | Refer to REMOVAL [09/2012 - ] | |
| "Close the hood or the trunk to use Brake Hold" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Electronically controlled brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Skid control ECU | Refer to REMOVAL [09/2012 - ] | |
| "TRAC OFF" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Electronically controlled brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Skid control ECU | Refer to REMOVAL [09/2012 - ] | |
| "Depress the brake pedal to continue Brake Hold" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Electronically controlled brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Skid control ECU | Refer to REMOVAL [09/2012 - ] | |
| "Close the door to continue Brake Hold" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Electronically controlled brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Skid control ECU | Refer to REMOVAL [09/2012 - ] | |
| "Fasten the seat belt to continue Brake Hold" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Electronically controlled brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Skid control ECU | Refer to REMOVAL [09/2012 - ] | |
| "Check Cruise Control System" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Dynamic Radar Cruise Control System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Dynamic radar cruise control system (w/ Dynamic Radar Cruise Control System) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Driving support ECU | Refer to REMOVAL [09/2012 - ] | |
| "Check Cruise Control System Depress the brake pedal" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Dynamic Radar Cruise Control System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Dynamic radar cruise control system (w/ Dynamic Radar Cruise Control System) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Driving support ECU | Refer to REMOVAL [09/2012 - ] | |
| "Clean Radar Sensor" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Dynamic Radar Cruise Control System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Dynamic radar cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Driving support ECU | Refer to REMOVAL [09/2012 - ] | |
| "Cruise Control not available" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Dynamic Radar Cruise Control System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Dynamic radar cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Driving support ECU | Refer to REMOVAL [09/2012 - ] | |
| "Cruise Control not available now" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Dynamic Radar Cruise Control System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Dynamic radar cruise control system (w/ Dynamic Radar Cruise Control System) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Driving support ECU | Refer to REMOVAL [09/2012 - ] | |
| "Front Radar Beam Adjustment" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Dynamic Radar Cruise Control System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Dynamic radar cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Driving support ECU | Refer to REMOVAL [09/2012 - ] | |
| "Check PCS System" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Pre-collision System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Pre-collision system (w/ Driver Monitor Camera) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| Pre-collision system (w/o Driver Monitor Camera) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Driving support ECU | Refer to REMOVAL [09/2012 - ] | |
| "BRAKE!" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Pre-collision System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Pre-collision system (w/ Driver Monitor Camera) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| Pre-collision system (w/o Driver Monitor Camera) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Driving support ECU | Refer to REMOVAL [09/2012 - ] | |
| "PCS not available now" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Pre-collision System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Pre-collision system (w/ Driver Monitor Camera) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| Pre-collision system (w/o Driver Monitor Camera) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Driving support ECU | Refer to REMOVAL [09/2012 - ] | |
| "Pre-crash brakes are disabled because VSC is OFF" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Pre-collision System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Pre-collision system (w/ Driver Monitor Camera) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| Pre-collision system (w/o Driver Monitor Camera) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Driving support ECU | Refer to REMOVAL [09/2012 - ] | |
| "Check LKA System" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Lane-keeping Assist System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Lane-keeping assist system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Driving support ECU | Refer to REMOVAL [09/2012 - ] | |
| "LKA not available" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Lane-keeping Assist System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Lane-keeping assist system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Driving support ECU | Refer to REMOVAL [09/2012 - ] | |
| "LKA Camera Adjustment" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Lane-keeping Assist System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Lane-keeping assist system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Driving support ECU | Refer to REMOVAL [09/2012 - ] | |
| "LKA canceled Keep hands on steering wheel" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Lane-keeping Assist System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Lane-keeping assist system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Driving support ECU | Refer to REMOVAL [09/2012 - ] | |
| "Check Park Sonar System" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Intuitive Parking Assist System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Intuitive parking assist system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Clearance warning ECU | Refer to REMOVAL [09/2012 - ] | |
| "Clean Park Sonar" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Intuitive Parking Assist System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Intuitive parking assist system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Clearance warning ECU | Refer to REMOVAL [09/2012 - ] | |
| "High Transmission Fluid temperature" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Automatic transmission system (AA80E) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| Automatic transmission system (AA80F) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| TCM (for AA80E) | Refer to REMOVAL [09/2012 - ] | |
| TCM (for AA80F) | Refer to REMOVAL [09/2012 - ] | |
| "Limited seat adjustability When adjusting the seat backwards, fold the table down" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for 4-Passenger with Ottoman) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Rear power seat control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Rear power seat module switch | Refer to REMOVAL [09/2012 - ] | |
| "Limited seat adjustability When adjusting the seat backwards, retract the ottoman" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for 4-Passenger with Ottoman) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Rear power seat control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Rear power seat module switch | Refer to REMOVAL [09/2012 - ] | |
| "Check Front Passenger Seat System" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Front power seat control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Front power seat switch RH | Refer to DISASSEMBLY [09/2012 - ] | |
| "BSM not available" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Blind Spot Monitor System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Blind spot monitor system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Blind spot monitor sensor | Refer to REMOVAL [09/2012 - ] | |
| "Check BSM System" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Blind Spot Monitor System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Blind spot monitor system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Blind spot monitor sensor | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| "Check NAVI BRAKE ASSIST System" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Navigation System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Navigation system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Multi-media module receiver assembly | Refer to REMOVAL [09/2012 - ] | |
| Multi-information display is missing dots | Perform Active Test (Meter Display 1) | Refer to DATA LIST / ACTIVE TEST [09/2012 - ] |
| Meter display panel | Refer to DISASSEMBLY [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| The settings cannot be customized through the multi-information display (Language) | No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] |
| The settings cannot be customized through the multi-information display (Units) | No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] |
| The settings cannot be customized through the multi-information display (ECO lamp) | No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] |
| The settings cannot be customized through the multi-information display (Drive monitor) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Air conditioning amplifier | Refer to REMOVAL [09/2012 - ] | |
| ECM | Refer to REMOVAL [09/2012 - ] | |
| The settings cannot be customized through the multi-information display (Lamp brightness) | No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] |
| The settings cannot be customized through the multi-information display (SPORT lamp) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| ECM | Refer to REMOVAL [09/2012 - ] | |
| The settings cannot be customized through the multi-information display (Default settings) | No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] |
- EPB*: Electric Parking Brake System
BUZZER
| Symptom | Suspected Area | Refer to |
|---|---|---|
| No buzzers operate | No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] |
| Seat belt warning buzzer does not operate (Front seat belt warning light operates normally) | No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] |
| Smart key warning buzzer does not operate (Smart access system operates normally) | No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] |
| Engine immobiliser certification buzzer does not operate (Engine immobiliser system operates normally) | No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] |
| Multi buzzer does not operate (Other system operates normally) | No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] |
| Dynamic radar cruise control low speed vehicle-to-vehicle warning buzzer does not operate (Dynamic radar cruise control system operates normally) (w/ Dynamic Radar Cruise Control System) | No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] |
| Brake hold control unreleased warning buzzer does not operate (Electronically controlled brake system operates normally) | No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] |
| LKA buzzer does not operate (Lane-keeping assist system operates normally) (w/ Lane-keeping Assist System) | No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] |
| Dynamic radar cruise control low speed cancel buzzer does not operate (Dynamic radar cruise control system operates normally) (w/ Dynamic Radar Cruise Control System) | No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] |
| Dynamic radar cruise control warning buzzer does not operate (Dynamic radar cruise control system operates normally) (w/ Dynamic Radar Cruise Control System) | No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] |
| PKB-ON driving warning buzzer does not operate (Brake warning light operates normally) | No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] |
| Driving with any door opened warning buzzer does not operate (Open door warning light and speedometer operate normally) | No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] |
| Sports shift reject buzzer does not operate (Others system operates normally) | No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] |
| Sliding roof open warning buzzer does not operate (Others system operates normally) (w/ Sliding Roof) | No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] |
OTHERS
| Symptom | Suspected Area | Refer to |
|---|---|---|
| Entire combination meter does not operate | Proceed to "Entire Combination Meter does not Operate" | Refer to Entire Combination Meter does not Operate |
| Eco/Sport light malfunction | Check customize setting | Refer to CUSTOMIZE PARAMETERS [09/2012 - ] |
| CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| ECM | Refer to REMOVAL [09/2012 - ] | |
| ODO/TRIP switch malfunction | ODO/TRIP switch circuit | Refer to Odo/Trip Switch Malfunction |
| Operating light control rheostat does not change light brightness | Light control rheostat circuit | Refer to Operating Light Control Rheostat does not Change Light Brightness |
| Meter illumination is always dark | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Lighting system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] | |
| Main body ECU (driver side junction block) | - | |
| Multi-information display does not change using DISP switch | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2012 - ] |
| Read the Data List (Multi Display Select Switch, DISP Switch) | Refer to DATA LIST / ACTIVE TEST [09/2012 - ] | |
| Steering pad switch assembly | Refer to INSPECTION [09/2012 - ] | |
| Spiral cable | Refer to INSPECTION [09/2012 - ] | |
| No. 1 meter ECU | Refer to DISASSEMBLY [09/2012 - ] |