Disassembly [09/2012 - ]

REMOVE NO. 1 COMBINATION METER BRACKET

Fig 1: Identifying No. 1 Combination Meter Bracket
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
1. Remove the No. 1 combination meter bracket.
REMOVE NO. 1 SIDE DEFROSTER NOZZLE DUCT

Fig 2: Identifying No. 1 Side Defroster Nozzle Duct Claw And Screw
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
1. Remove the screw.
2. Detach the claw and remove the No. 1 side defroster nozzle duct.
REMOVE NO. 2 SIDE DEFROSTER NOZZLE DUCT

Fig 3: Identifying No. 2 Side Defroster Nozzle Duct Claw And Screw
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
1. Remove the screw.
2. Detach the claw and remove the No. 2 side defroster nozzle duct.
REMOVE NO. 1 HEATER TO REGISTER DUCT

Fig 4: Identifying No. 1 Heater To Register Duct Screws
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
1. Remove the 3 screws and No. 1 heater to register duct.
REMOVE NO. 3 HEATER TO REGISTER DUCT

Fig 5: Identifying No. 3 Heater To Register Duct Screws
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
1. Remove the 3 screws and No. 3 heater to register duct.
REMOVE DEFROSTER NOZZLE ASSEMBLY

Fig 6: Identifying Defroster Nozzle Assembly Screws
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
1. Remove the 3 screws and defroster nozzle assembly.

REMOVE NO. 2 HEATER TO REGISTER DUCT

Fig 7: Identifying No. 2 Heater To Register Duct (W/ Ion Generator) Screws

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

w/ Ion Generator:

Disconnect the hose from the ion generator sub-assembly.

TEXT IN ILLUSTRATION

Hose

Remove the 2 screws and No. 2 heater to register duct.

w/o Ion Generator:
Remove the 2 screws and No. 2 heater to register duct.

Fig 8: Identifying No. 2 Heater To Register Duct (W/O Ion Generator) Screws
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

REMOVE ION GENERATOR SUB-ASSEMBLY (w/ Ion Generator) . Refer to REMOVAL [09/2012 - ] - Step 2
REMOVE NO. 2 INSTRUMENT PANEL WIRE . Refer to REMOVAL [09/2012 - ] - Step 8
REMOVE FRONT PASSENGER AIRBAG ASSEMBLY . Refer to REMOVAL [09/2012 - ] - Step 9
REMOVE NAVIGATION ANTENNA ASSEMBLY . Refer to REMOVAL [09/2012 - ] - Step 8
REMOVE AUTOMATIC LIGHT CONTROL SENSOR
1. Disconnect the connector.
2. Detach the 2 claws and remove the automatic light control sensor.
  
  Fig 9: Removing Solar Sensor
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
REMOVE NO. 2 INSTRUMENT PANEL WIRE
1. w/o Ion Generator:
  Detach the wire harness clamp and remove the No. 2 instrument panel wire.
  
  Fig 10: Identifying No. 2 Instrument Panel Wire (W/O Ion Generator) Clamp
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. w/ Ion Generator:
  Detach the 5 wire harness clamps and remove the No. 2 instrument panel wire.
  
  Fig 11: Identifying No. 2 Instrument Panel Wire (W/ Ion Generator) Clamps
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
REMOVE NO. 1 INSTRUMENT PANEL PIN
HINT:

Use the same procedure to remove the No. 1 instrument panel pin on the other side.
1. Remove the screw and No. 1 instrument panel pin.
  
  Fig 12: Identifying No. 1 Instrument Panel Pin Screw
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
REMOVE NO. 1 METER HOOD RETAINER

Fig 13: Identifying No. 1 Meter Hood Retainers Screws
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
1. Remove the 2 screws and 2 No. 1 meter hood retainers.
REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY

Fig 14: Identifying Protective Tape And No. 1 Instrument Panel Register Assembly Claws
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
1. Apply protective tape as shown in the illustration.
  TEXT IN ILLUSTRATION
  
  *1 Protective Tape
2. Detach the 4 claws and remove the No. 1 instrument panel register assembly.
REMOVE NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY

Fig 15: Identifying Protective Tape And No. 2 Instrument Panel Register Assembly Claws
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
1. Apply protective tape as shown in the illustration.
  TEXT IN ILLUSTRATION
  
  *1 Protective Tape
2. Detach the 4 claws and remove the No. 2 instrument panel register assembly.