Front and Rear Switch Cannot Operate Rear Sunshade: Procedure

1. Clear the DTCs. Refer to DTC CHECK/CLEAR .
2. Check for DTCs. Refer to DTC CHECK/CLEAR .
   RESULT
   
   

   Result	Proceed to
   DTC is not output	A
   DTC U0141, U0210, U1114 is output	B
   DTC U1127 is output	C

B → See step   9 

C → See step   10 

A: Go to next step 

1. Select the Active Test, use the Techstream to generate a control command, and then check that the shade raises/lowers. Refer to DATA LIST/ACTIVE TEST .
   BODY NO. 4
   
   

   Tester Display	Test Part	Control Range	Diagnostic Note
   Rear Sunshade Operation	Rear Sunshade Operation	Down, No or Up	-

   OK

   Rear sunshade raises or lowers.

NG → See step   5 

OK: Go to next step 

1. Use the Data List to check if the rear sunshade limit switch is functioning properly. Refer to DATA LIST/ACTIVE TEST .
   BODY NO. 4
   
   

   Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
   Rear Sunshade Close	Status of the rear sunshade close/YES or NO	YES: Rear sunshade limit switch is OFF (Rear sunshade is lowered) NO: Rear sunshade limit switch is ON (Rear sunshade is raised)	-

   OK

   Rear sunshade raises or lowers.

OK → See step   5 

NG: Go to next step 

Fig 1: Disconnecting S25 Shade & S61 ECU Connector

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Disconnect the S25 shade connector.
2. Disconnect the S61 ECU connector.
3. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   S25-3 (RSL) - S61-22 (LMT)	Always	Below 1 Ω
   S25-3 (RSL) - Body ground	Always	10 kΩ or higher

NG → REPAIR OR REPLACE HARNESS OR CONNECTOR 

OK → See step   13 

1. Remove the RR S/SHADE fuse from luggage room junction block.
2. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   RR S/SHADE fuse	Always	Below 1 Ω

NG → REPLACE FUSE 

OK: Go to next step 

Fig 2: Disconnecting LG Junction Block Connector

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Disconnect the LG junction block connector.
2. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   LG-1 - Body ground	Always	11 to 14 V

NG → REPAIR OR REPLACE HARNESS OR CONNECTOR 

OK: Go to next step 

Fig 3: Disconnect S25 Shade & S61 ECU Connectors

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Disconnect the S25 shade connector.
2. Disconnect the S61 ECU connector.
3. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   S25-2 (RSMU) - S61-4 (MU)	Always	Below 1 Ω
   S25-1 (RSMD) - S61-3 (MD)	Always	Below 1 Ω
   S25-4 (RSE) - Body ground	Always	Below 1 Ω
   S25-2 (RSMU) - Body ground	Always	10 kΩ or higher
   S25-1 (RSMD) - Body ground	Always	10 kΩ or higher

NG → REPAIR OR REPLACE HARNESS OR CONNECTOR 

OK: Go to next step 

1. Remove the rear window shade assembly. Refer to REMOVAL .
   Fig 4: Identifying Rear Window Shade Assembly

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Apply battery voltage and check the operation of the window shade motor.
   STANDARD
   
   

   Measurement Condition	Specified Condition
   Battery positive (+) → 1 (RSMD) Battery negative (-) → 4 (RSE)	Sunshade lowers
   Battery positive (+) → 2 (RSMU) Battery negative (-) → 4 (RSE)	Sunshade raises

NG → See step   12 

OK → See step   11