On-Vehicle Inspection

INSPECT SPEEDOMETER

Check the operation.

NOTE:

The meter CPU receives the vehicle speed signal from the skid control ECU via a direct line. Therefore, perform the following inspection referring to values on the Data List of the skid control ECU because it is the source of the vehicle speed signal.
The Data List values of the skid control ECU are used for this inspection. Therefore, make sure to perform the inspection after confirming that no DTCs are output from the brake control system.
If the tire size or tire inflation pressure is not within the specified range, or the tires are excessively worn, the speedometer indication error will increase. Therefore, make sure to perform the inspection after checking that the tire size, tire inflation pressure and tire wear are in the specified range.

Before starting the following inspection, check if the Brake Control System outputs the DTCs.

Check the values by referring to the table below.

ABS/VSC/TRAC

Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
Vehicle Speed	Vehicle speed/Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)	Almost same as actual vehicle speed (When driving)	-

REFERENCE: MPH (FOR U.S.A.)

Techstream Indication (mph)	Acceptable Range for Speedometer (mph)	Acceptable Range for Speedometer LCD (mph)
20	20.0 to 23.0	19.5 to 22.0
40	40.0 to 43.5	39.9 to 42.7
60	60.0 to 64.0	60.6 to 63.4
80	80.0 to 84.5	81.1 to 84.3
100	100.0 to 105.0	101.7 to 104.9
120	120.0 to 125.5	122.4 to 125.6
140	140.0 to 146.0	143.1 to 146.3
160	160.0 to 166.5	163.7 to 166.9

REFERENCE: KM/H (FOR CANADA)

Techstream Indication (km/h)	Acceptable Range for Speedometer (km/h) Data in () is for reference	Acceptable Range for Speedometer LCD (km/h)
20	(17.5 to 21.5)	18.7 to 22.7
40	38.0 to 42.0	39.1 to 43.6
60	58.0 to 63.0	59.8 to 64.3
80	78.0 to 84.0	80.2 to 89.2
100	98.5 to 104.5	100.8 to 105.8
120	119.0 to 125.0	121.5 to 126.5
140	139.0 to 146.0	142.2 to 147.2
160	159.0 to 167.0	162.8 to 167.8
180	179.0 to 188.0	183.5 to 188.5
200	199.0 to 209.0	204.2 to 209.2
220	219.0 to 230.0	224.8 to 229.8
240	239.0 to 251.0	245.5 to 250.5
260	259.0 to 272.0	266.2 to 271.2
280	279.0 to 293.0	286.8 to 291.8

REFERENCE: KM/H (FOR KOREA)

Techstream Indication (km/h)	Acceptable Range for Speedometer (km/h) Data in () is for reference	Acceptable Range for Speedometer LCD (km/h)
20	(21.0 to 25.0)	21.0 to 25.0
40	41.7 to 46.2	42.0 to 46.0
60	62.7 to 67.2	63.0 to 67.0
80	83.4 to 88.4	84.0 to 88.0
100	104.3 to 109.3	104.0 to 109.0
120	125.1 to 130.6	125.0 to 130.0
140	145.8 to 151.8	146.0 to 151.0
160	166.2 to 173.2	167.0 to 173.0
180	186.9 to 194.5	187.0 to 194.0
200	207.7 to 215.7	208.0 to 215.0
220	228.4 to 236.8	229.0 to 236.0
240	249.2 to 258.0	249.0 to 257.0
260	269.9 to 279.2	270.0 to 278.0
280	290.6 to 300.4	291.0 to 299.0

NOTE:

Tire wear as well as over or under inflation will cause errors.

HINT:

If the indication is not as specified, go to Problem Symptoms Table. Refer to PROBLEM SYMPTOMS TABLE .

INSPECT TACHOMETER

Compare the test results with the tachometer indications.

DC 13.5 V, AT 25°C (77°F)

Techstream Indication (rpm)	Acceptable Range (rpm) Data in () is for reference
700	630 to 770
1, 000	(900 to 1, 100)
2, 000	(1, 850 to 2, 150)
3, 000	2, 800 to 3, 200
4, 000	(3, 829 to 4, 229)
5, 000	4, 859 to 5, 259
6, 000	(5, 838 to 6, 338)
7, 000	6, 800 to 7, 400
8, 000	(7, 800 to 8, 400)

HINT:

If the indication is not as specified, go to Problem Symptoms Table. Refer to PROBLEM SYMPTOMS TABLE .