LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2012 >> CT 200h F Sport >> Repair and Diagnosis >> Restraints >> Air Bag, SRS >> Airbag System (Diagnostic Codes (B1000/31 - B1635/24)) >> Airbag System >> DTC B1612/83: Lost Communication with Front Airbag Sensor RH; DTC B1613/83: Front Airbag Sensor RH Initialization Incomplete >> Procedure

DTC B1612/83: Lost Communication with Front Airbag Sensor RH; DTC B1613/83: Front Airbag Sensor RH Initialization Incomplete: Procedure

  1. CHECK CONNECTORS 
    1. Turn the power switch off.
    2. Disconnect the cable from the negative (-) auxiliary battery terminal.
      WARNING:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. Check that the connectors are properly connected to the airbag sensor assembly and front airbag sensor RH. Also check that the connectors that link the engine room main wire and instrument panel wire are properly connected.

      OK

      The connectors are properly connected.

      HINT: 

      If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

    4. Disconnect the connectors from the airbag sensor assembly and front airbag sensor RH. Also disconnect the connectors that link the engine room main wire and instrument panel wire.
    5. Check that the terminals of the connectors are not damaged.

      OK

      The terminals are not deformed or damaged.

    NG → REPLACE WIRE HARNESS 

    OK: Go to next step 

  2. CHECK FRONT AIRBAG SENSOR RH CIRCUIT (OPEN) 
    1. Connect the connectors that link the engine room main wire and instrument panel wire.
      Fig 1: Identifying H84 And A44 Connector Terminals
      GTY355758Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Using SST, connect terminals 29 (+SR) and 27 (-SR) of connector B.
      NOTE:

      Do not forcibly insert SST into the terminals of the connector when connecting.

      • SST: 09843-18040 
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      A44-2 (+SR) - A44-1 (-SR) Always Below 1 Ω
      TEXT IN ILLUSTRATION

      *1 Front Airbag Sensor RH *2 Airbag Sensor Assembly
      *3 Connector B *4 Connector E
      *a Front view of wire harness connector
      (to Airbag Sensor Assembly)      		 *b Front view of wire harness connector
      (to Front Airbag Sensor RH)

    NG → See step   7 

    OK: Go to next step 

  3. CHECK FRONT AIRBAG SENSOR RH CIRCUIT (SHORT) 
    1. Disconnect SST from connector B.
      Fig 2: Identifying A44 Connector Terminals
      GTY355593Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      A44-2 (+SR) - A44-1 (-SR) Always 1 MΩ or higher
      TEXT IN ILLUSTRATION

      *1 Front Airbag Sensor RH
      *2 Airbag Sensor Assembly
      *3 Connector E
      *a Front view of wire harness connector
      (to Front Airbag Sensor RH)

    NG → See step   8 

    OK: Go to next step 

  4. CHECK FRONT AIRBAG SENSOR RH CIRCUIT (SHORT TO B+) 
    1. Connect the cable to the negative (-) auxiliary battery terminal.
      Fig 3: Identifying A44 Connector Terminals
      GTY355593Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Turn the power switch on (IG).
    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Switch Condition Specified Condition
      A44-2 (+SR) - Body ground Power switch on (IG) Below 1 V
      A44-1 (-SR) - Body ground Power switch on (IG) Below 1 V
      TEXT IN ILLUSTRATION

      *1 Front Airbag Sensor RH
      *2 Airbag Sensor Assembly
      *3 Connector E
      *a Front view of wire harness connector
      (to Front Airbag Sensor RH)

    NG → See step   9 

    OK: Go to next step 

  5. CHECK FRONT AIRBAG SENSOR RH CIRCUIT (SHORT TO GROUND) 
    1. Turn the power switch off.
      Fig 4: Identifying A44 Connector Terminals
      GTY355593Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disconnect the cable from the negative (-) auxiliary battery terminal.
      WARNING:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      A44-2 (+SR) - Body ground Always 1 MΩ or higher
      A44-1 (-SR) - Body ground Always 1 MΩ or higher
      TEXT IN ILLUSTRATION

      *1 Front Airbag Sensor RH
      *2 Airbag Sensor Assembly
      *3 Connector E
      *a Front view of wire harness connector
      (to Front Airbag Sensor RH)

    NG → See step   10 

    OK: Go to next step 

  6. CHECK FRONT AIRBAG SENSOR RH 
    1. Connect the connector to the airbag sensor assembly.
      Fig 5: Identifying Front Airbag Sensor RH
      GTY245347Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Interchange the front airbag sensor RH with LH and connect the connectors.
    3. Connect the cable to the negative (-) auxiliary battery terminal.
    4. Turn the power switch on (IG), and wait for at least 60 seconds.
    5. Clear the DTCs stored in memory. Refer to DTC CHECK / CLEAR .
    6. Turn the power switch off.
    7. Turn the power switch on (IG), and wait for at least 60 seconds.
    8. Check for DTCs. Refer to DTC CHECK / CLEAR .

      Result

      Result Proceed to
      DTCs B1612/83, B1613/83, B1617/84 and B1618/84 are not output. A
      DTC B1617/84 or B1618/84 is output. B
      DTC B1612/83 or B1613/83 is output. C
      TEXT IN ILLUSTRATION

      *1 Front Airbag Sensor LH
      *2 Airbag Sensor Assembly

      HINT: 

      Codes other than DTCs B1612/83, B1613/83, B1617/84 and B1618/84 may be output at this time, but they are not related to this check.

    B → See step   13 

    C → See step   12 

    A → See step   11 

  7. CHECK INSTRUMENT PANEL WIRE (OPEN) 
    1. Disconnect the instrument panel wire connector from the engine room main wire.
      Fig 6: Identifying H84 And AH6 Connector Terminals
      GTY352762Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      HINT: 

      SST has already been inserted into connector B.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      AH6-1 (+SR) - AH6-2 (-SR) Always Below 1 Ω
      TEXT IN ILLUSTRATION

      *1 Front Airbag Sensor RH *2 Airbag Sensor Assembly
      *3 Engine Room Main Wire *4 Instrument Panel Wire
      *5 Connector B *6 Connector C
      *a Front view of wire harness connector
      (to Airbag Sensor Assembly)      		 *b Front view of wire harness connector
      (to Engine Room Main Wire)

    NG → REPLACE INSTRUMENT PANEL WIRE 

    OK → REPLACE ENGINE ROOM MAIN WIRE 

  8. CHECK INSTRUMENT PANEL WIRE (SHORT) 
    1. Disconnect the instrument panel wire connector from the engine room main wire.
      Fig 7: Identifying AH6 Connector Terminals
      GTY347769Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      AH6-1 (+SR) - AH6-2 (-SR) Always 1 MΩ or higher
      TEXT IN ILLUSTRATION

      *1 Front Airbag Sensor RH
      *2 Airbag Sensor Assembly
      *3 Engine Room Main Wire
      *4 Instrument Panel Wire
      *5 Connector C
      *a Front view of wire harness connector
      (to Engine Room Main Wire)

    NG → REPLACE INSTRUMENT PANEL WIRE 

    OK → REPLACE ENGINE ROOM MAIN WIRE 

  9. CHECK INSTRUMENT PANEL WIRE (SHORT TO B+) 
    1. Turn the power switch off.
      Fig 8: Identifying AH6 Connector Terminals
      GTY347769Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disconnect the cable from the negative (-) auxiliary battery terminal.
      WARNING:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. Disconnect the instrument panel wire connector from the engine room main wire.
    4. Connect the cable to the negative (-) auxiliary battery terminal.
    5. Turn the power switch on (IG).
    6. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Switch Condition Specified Condition
      AH6-1 (+SR) - Body ground Power switch on (IG) Below 1 V
      AH6-2 (-SR) - Body ground Power switch on (IG) Below 1 V
      TEXT IN ILLUSTRATION

      *1 Front Airbag Sensor RH
      *2 Airbag Sensor Assembly
      *3 Engine Room Main Wire
      *4 Instrument Panel Wire
      *5 Connector C
      *a Front view of wire harness connector
      (to Engine Room Main Wire)

    NG → REPLACE INSTRUMENT PANEL WIRE 

    OK → REPLACE ENGINE ROOM MAIN WIRE 

  10. CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND) 
    1. Disconnect the instrument panel wire connector from the engine room main wire.
      Fig 9: Identifying AH6 Connector Terminals
      GTY347769Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      AH6-1 (+SR) - Body ground Always 1 MΩ or higher
      AH6-2 (-SR) - Body ground Always 1 MΩ or higher
      TEXT IN ILLUSTRATION

      *1 Front Airbag Sensor RH
      *2 Airbag Sensor Assembly
      *3 Engine Room Main Wire
      *4 Instrument Panel Wire
      *5 Connector C
      *a Front view of wire harness connector
      (to Engine Room Main Wire)

    NG → REPLACE INSTRUMENT PANEL WIRE 

    OK → REPLACE ENGINE ROOM MAIN WIRE 

  11. USE SIMULATION METHOD TO CHECK. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING 
  12. REPLACE AIRBAG SENSOR ASSEMBLY. Refer to  REMOVAL 
  13. REPLACE FRONT AIRBAG SENSOR RH. Refer to  REMOVAL 
scientia non olet · About LEMON Manuals