LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2011 >> RX 350 AWD >> Repair and Diagnosis (Single Page) >> Accessories & Equipment >> Infotainment >> Navigation System (For DVD) (Diagnostic Codes & Symptom Tests) >> NAVIGATION SYSTEM (for DVD) >> DTC B1593: No Response from Stereo Component Amplifier; DTC B15D3: Stereo Component Amplifier Disconnected >> Procedure

DTC B1593: No Response from Stereo Component Amplifier; DTC B15D3: Stereo Component Amplifier Disconnected: Procedure

  1. CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING) 
    1. Check for optional components.
      1. Check that optional components (including associated wiring) which generate radio waves are not installed.

        Result

        Result Proceed to
        Optional components (including associated wiring) are installed. A
        Optional components (including associated wiring) are not installed. B

        HINT: 

        • Electrical noise from radio waves generated by optional components or the wiring for those components may affect MOST communication.
        • This DTC may be stored when a MOST communication error occurs due to electrical noise.

    B → See step   3 

    A: Go to next step 

  2. REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING) 
    1. Remove optional components (including associated wiring).
      NOTE:

      Do not remove optional components or associated wiring without the permission of the customer.

    NEXT: Go to next step 

  3. CHECK DTC 
    1. Clear the DTCs. Refer to DTC CHECK / CLEAR .
    2. Recheck for DTCs and check if the same DTC is output again.

      OK

      No DTCs are output.

    NG → See step   4 

    OK → END 

  4. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY POWER SOURCE) 
    1. Disconnect the stereo component amplifier assembly connector.
      Fig 1: Stereo Component Amplifier Assembly Connector
      GTY352230Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      O18-2 (GND) - Body ground Always Below 1 Ω
      O18-6 (GND2) - Body ground Always Below 1 Ω
    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      O18-1 (+B) - O18-2 (GND) Always 11 to 14 V
      O18-3 (+B2) - O18-2 (GND) Always 11 to 14 V
      TEXT IN ILLUSTRATION

      *1 Front view of wire harness connector
      (to Stereo Component Amplifier Assembly)

    NG → REPAIR OR REPLACE HARNESS OR CONNECTOR 

    OK: Go to next step 

  5. CHECK HARNESS AND CONNECTOR (MOST COMMUNICATION LINE) 
    1. Disconnect the display and navigation module display connector.
      Fig 2: Display And Navigation Module Display Connector
      GTY348507Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disconnect the stereo component amplifier assembly connector.
      Fig 3: Stereo Component Amplifier Assembly Connector
      GTY355163Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Disconnect the radio receiver assembly connector.
      Fig 4: Radio Receiver Assembly Connector
      GTY349376Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Measure the resistance between the display and navigation module display and stereo component amplifier assembly according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G6-1 (MI+) - O15-6 (MO+) Always Below 1 Ω
      G6-5 (MI-) - G15-12 (MO-) Always Below 1 Ω
      G6-2 (SLDI) - O15-11 (SLDO) Always Below 1 Ω
      G6-1 (MI+) - Body ground Always 10 kΩ or higher
      G6-5 (MI-) - Body ground Always 10 kΩ or higher
      G6-2 (SLDI) - Body ground Always 10 kΩ or higher
    5. Measure the resistance between the radio receiver assembly and stereo component amplifier assembly according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G12-11 (MO+) - O15-4 (MI+) Always Below 1 Ω
      G12-25 (MO-) - O15-10 (MI-) Always Below 1 Ω
      G12-24 (SLDI) - O15-5 (SLDI) Always Below 1 Ω
      G12-11 (MO+) - Body ground Always 10 kΩ or higher
      G12-25 (MO-) - Body ground Always 10 kΩ or higher
      G12-24 (SLDI) - Body ground Always 10 kΩ or higher
      TEXT IN ILLUSTRATION

      *1 Front view of wire harness connector
      (to Display and Navigation Module Display)
      *2 Front view of wire harness connector
      (to Stereo Component Amplifier Assembly)
      *3 Front view of wire harness connector
      (to Radio Receiver Assembly)

    NG → REPAIR OR REPLACE HARNESS OR CONNECTOR 

    OK: Go to next step 

  6. REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY 
    1. Replace the stereo component amplifier assembly. Refer to REMOVAL .
    2. Clear the DTCs. Refer to DTC CHECK / CLEAR .
    3. Recheck for DTCs and check if the same DTC is output again.

      OK

      No DTCs are output.

    NG → See step   7 

    OK → END 

  7. REPLACE DISPLAY AND NAVIGATION MODULE DISPLAY. Refer to  REMOVAL