LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2011 >> LX 570 >> Repair and Diagnosis >> Accessories & Equipment >> Gauges & Instrument Panels >> Meter / Gauge / Display (Service Information) >> Combination Meter >> Removal (08/2010 - 08/2011) >> Removal

Removal (08/2010 - 08/2011): Removal

  1. DISABLE AUTOAWAY/RETURN FUNCTION 
    1. Disable the Autoaway/Return function by changing the customize parameter. Refer to CUSTOMIZE PARAMETERS .
      NOTE:

      Record the current customize parameter setting (whether the Autoaway/Return function is enabled or disabled) in order to restore the current setting after finishing the operation.

      HINT: 

      Performing the above operation causes the Autoaway/Return function to be disabled when the engine switch is turned off.

    2. Turn the engine switch on (IG). Operate the tilt and telescopic switch to fully extend and lower the steering column.
    3. Turn the engine switch off.
  2. REMOVE ENGINE ROOM SIDE COVER LH  . Refer to REMOVAL - Step 1
  3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 
    NOTE:
    • w/ Navigation System:

      After the engine switch is turned off, the HDD navigation system requires approximately 6 minutes to record various types of memory and settings. As a result, after turning the engine switch off, wait 6 minutes or more before disconnecting the cable from the negative (-) battery terminal.

    • When disconnecting the cable, some systems need to be initialized after the cable is reconnected. Refer to INITIALIZATION .
  4. REMOVE INSTRUMENT SIDE PANEL LH 
    1. Place protective tape as shown in the illustration.
      Fig 1: Identifying Side Panel Claws
      GTY153870Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Using a moulding remover, detach the 6 claws and remove the side panel.
  5. REMOVE NO. 1 SWITCH HOLE BASE 
    1. Detach the 5 claws.
      Fig 2: Identifying No. 1 Switch Hole Base And Claws
      GTY143850Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the hole base and disconnect the connectors.
  6. REMOVE LOWER INSTRUMENT PANEL PAD SUB-ASSEMBLY LH 
    1. Detach the 8 claws.
      Fig 3: Identifying Lower Instrument Panel Pad Sub-Assembly LH And Claws
      GTY153711Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the instrument panel pad and disconnect the connector.
  7. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY 
    1. Detach the 6 claws.
      Fig 4: Identifying Instrument Cluster Finish Panel Sub-Assembly And Claws
      GTY153706Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Detach the 4 claws.
      Fig 5: Identifying Finish Panel And Claws
      GTY153705Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Remove the finish panel and disconnect the connectors.
  8. REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY 
    1. Detach the 4 claws and remove the register.
      Fig 6: Identifying No. 1 Instrument Panel Register Assembly And Claws
      GTY153707Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  9. REMOVE NO. 3 INSTRUMENT PANEL REGISTER ASSEMBLY 
    1. Detach the 5 claws and remove the register.
      Fig 7: Identifying No. 3 Instrument Panel Register Assembly And Claws
      GTY153708Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  10. REMOVE COMBINATION METER ASSEMBLY 
    1. Remove the 2 screws.
      Fig 8: Identifying Combination Meter Assembly And Screw
      GTY137270Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Detach the 2 clips.
      Fig 9: Identifying Combination Meter Assembly Clips Location
      GTY358343Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Disconnect the connector and remove the combination meter.
      Fig 10: Locating Combination Meter
      GTY153709Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
scientia non olet · About LEMON Manuals