Transmission Control Switch Circuit (TO 08/2009): Procedure

1. Disconnect the transmission control switch connector of shift lock control unit assembly.
   Fig 1: Identifying F30 Transmission Control Switch Connector

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Measure the voltage according to the value(s) in the table below.

   Standard Voltage

   Tester Connection	Condition	Specified Condition
   F30-6 (IG) - Body ground or other terminals	Engine switch on (IG)	11 to 14 V
   	Engine switch off	Below 1 V

   TEXT IN ILLUSTRATION
   
   

   *1	Front view of wire harness connector (to Transmission Control Switch)

NG → REPAIR OR REPLACE HARNESS OR CONNECTOR 

OK: Go to next step 

1. Measure the resistance according to the value(s) in the table below.
   Fig 2: Identifying F30 Transmission Control Switch Connector

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   F30-11 (E) - Body ground or other terminals	Always	Below 1 Ω

   TEXT IN ILLUSTRATION
   
   

   *1	Front view of wire harness connector (to Transmission Control Switch)

NG → REPAIR OR REPLACE HARNESS OR CONNECTOR 

OK: Go to next step 

1. Measure the resistance between each terminal of the transmission control switch when the shift lever is moved to each position.
   Fig 3: Identifying F30 Transmission Control Switch

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   6 (IG) - 13 (S)	Shift lever in S, "+" or "-"	Below 1 Ω
   	Shift lever not in S, "+" or "-"	10 kΩ or higher
   5 (SFTU) - 11 (E)	Shift lever held in "+" (Up-shift)	Below 1 Ω
   	Shift lever not held in "+"	10 kΩ or higher
   4 (SFTD) - 11 (E)	Shift lever held in "-" (Down-shift)	Below 1 Ω
   	Shift lever not held in "-"	10 kΩ or higher

   TEXT IN ILLUSTRATION
   
   

   *1	Component without harness connected (Transmission Control Switch)

NG → See step   6 

OK: Go to next step 

1. Connect the transmission control switch connector.
   Fig 4: Identifying A43 ECM Connector

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Disconnect the ECM connector.
3. Turn the engine switch on (IG).
4. Measure the voltage according to the value(s) in the table below.

   Standard Voltage

   Tester Connection	Condition	Specified Condition
   A43-25 (S) - Body ground or other terminals	Engine switch on (IG) Shift lever in S, "+" or "-"	11 to 14 V
   A43-25 (S) - Body ground or other terminals	Engine switch on (IG) Shift lever not in S, "+" or "-"	Below 1 V

   TEXT IN ILLUSTRATION
   
   

   *1	Front view of wire harness connector (to ECM)

5. Turn the engine switch off.
6. Disconnect the spiral cable connector.
7. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   A43-38 (SFTU) - Body ground or other terminals	Shift lever held in "+" (Up-shift)	Below 1 Ω
   	Shift lever not held in "+"	10 kΩ or higher
   A43-27 (SFTD) - Body ground or other terminals	Shift lever held in "-" (Down-shift)	Below 1 Ω
   	Shift lever not held in "-"	10 kΩ or higher

   TEXT IN ILLUSTRATION
   
   

   *1	Front view of wire harness connector (to ECM)

NG → REPAIR OR REPLACE HARNESS OR CONNECTOR 

OK → See step   5