LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2010 >> RX 350 FWD >> Repair and Diagnosis >> Accessories & Equipment >> Infotainment >> Audio / Video System (W/O Navigation) (Diagnostic Codes & Symptom Tests) (2 Of2) >> AUDIO AND VISUAL SYSTEM (w/o Navigation System) >> Microphone Circuit between Microphone and Radio Receiver (From 8/2009) >> Procedure

Microphone Circuit between Microphone and Radio Receiver (From 8/2009): Procedure

  1. CONFIRM MODEL 
    1. Choose the model to be inspected.

      Result

      Model Proceed to
      w/o Manual (SOS) Switch A
      w/ Manual (SOS) Switch B

    B → See step   5 

    A: Go to next step 

  2. CHECK HARNESS AND CONNECTOR 
    1. Disconnect the radio receiver assembly and map light assembly connectors.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G10-1 (SNS2) - T10-36 (SNS2) Always Below 1 Ω
      G10-3 (MACC) - T10-33 (MACC) Always Below 1 Ω
      G10-2 (MIN+) - T10-34 (MCO+) Always Below 1 Ω
      G10-5 (MIN-) - T10-35 (MCO-) Always Below 1 Ω
      G10-1 (SNS2) - Body ground Always 10 kΩ or higher
      G10-3 (MACC) - Body ground Always 10 kΩ or higher
      G10-2 (MIN+) - Body ground Always 10 kΩ or higher
      G10-5 (MIN-) - Body ground Always 10 kΩ or higher
      G10-6 (SGND) - Body ground Always 10 kΩ or higher

    NG → REPAIR OR REPLACE HARNESS OR CONNECTOR 

    OK: Go to next step 

  3. INSPECT RADIO RECEIVER ASSEMBLY 
    1. Disconnect the radio receiver assembly and map light assembly connectors.
      Fig 1: Identifying Radio Receiver Assembly And Map Light Assembly Connectors
      GTY280962Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      G10-3 (MACC) - Body ground Engine switch on (ACC) 4 to 6 V
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G10-6 (SGND) - Body ground Always Below 1 Ω
      G10-5 (MIN-) - Body ground Always Below 1 Ω
    4. Proceed to the next step based on the inspection result.

      Result

      Result Proceed to
      NG A
      OK B
      TEXT IN ILLUSTRATION

      *1 Component without harness connected
      (Radio Receiver Assembly)

    B → See step   10 

    A → See step   4 

  4. REPLACE RADIO RECEIVER ASSEMBLY. Refer to  REMOVAL 
  5. CHECK HARNESS AND CONNECTOR 
    1. Disconnect the radio receiver assembly and map light assembly connectors.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G10-1 (SNS2) - T10-36 (SNS2) Always Below 1 Ω

    NG → REPAIR OR REPLACE HARNESS OR CONNECTOR 

    OK: Go to next step 

  6. CHECK HARNESS AND CONNECTOR 
    1. Disconnect the radio receiver assembly and DCM (telematics transceiver) connectors.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G10-2 (MIN+) - G25-18 (MCO+) Always Below 1 Ω
      G10-5 (MIN-) - G25-19 (MCO-) Always Below 1 Ω
      G10-2 (MIN+) - Body ground Always 10 kΩ or higher
      G10-5 (MIN-) - Body ground Always 10 kΩ or higher
      G10-6 (SGND) - Body ground Always 10 kΩ or higher

    NG → REPAIR OR REPLACE HARNESS OR CONNECTOR 

    OK: Go to next step 

  7. CHECK HARNESS AND CONNECTOR 
    1. Disconnect the DCM (telematics transceiver) and map light assembly connectors.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G25-33 (MCVD) - T10-33 (MACC) Always Below 1 Ω
      G25-34 (MCI+) - T10-34 (MCO+) Always Below 1 Ω
      G25-35 (MCI-) - T10-35 (MCO-) Always Below 1 Ω
      G25-33 (MCVD) - Body ground Always 10 kΩ or higher
      G25-34 (MCI+) - Body ground Always 10 kΩ or higher
      G25-35 (MCI-) - Body ground Always 10 kΩ or higher
      G25-32 (SGND) - Body ground Always 10 kΩ or higher

    NG → REPAIR OR REPLACE HARNESS OR CONNECTOR 

    OK: Go to next step 

  8. INSPECT RADIO RECEIVER ASSEMBLY 
    1. Disconnect the radio receiver assembly and map light assembly connectors.
      Fig 2: Identifying Radio Receiver Assembly And Map Light Assembly Connectors
      GTY287754Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G10-6 (SGND) - Body ground Always Below 1 Ω
      G10-5 (MIN-) - Body ground Always Below 1 Ω
      TEXT IN ILLUSTRATION

      *1 Component without harness connected
      (Radio Receiver Assembly)

    NG → See step   14 

    OK: Go to next step 

  9. INSPECT DCM (TELEMATICS TRANSCEIVER) 
    1. Measure the voltage according to the value(s) in the table below.
      Fig 3: Identifying Measure The Voltage
      GTY265633Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard Voltage

      Tester Connection Condition Specified Condition
      G25-33 (MCVD) - Body ground Engine switch on (ACC) 4 to 6 V
      TEXT IN ILLUSTRATION

      *1 Component with harness connected
      (DCM (Telematics Transceiver))

    NG → See step   16 

    OK: Go to next step 

  10. INSPECT MAP LIGHT ASSEMBLY 
    1. Measure the resistance according to the value(s) in the table below.
      Fig 4: Measure The Resistance
      GTY254212Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard Resistance

      Tester Connection Condition Specified Condition
      T10-35 (MCO-) - T10-36 (SNS2) Always Below 1 Ω
      TEXT IN ILLUSTRATION

      *1 Component without harness connected
      (Map light assembly)

    NG → See step   13 

    OK: Go to next step 

  11. INSPECT MAP LIGHT ASSEMBLY 
    1. Reconnect the radio receiver assembly connector.
    2. Reconnect the DCM (telematics transceiver) connector*1.
      • *1: w/ Manual (SOS) Switch
    3. Reconnect the map light assembly connector.
      Fig 5: Identifying Map Light Assembly Connector
      GTY258792Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Turn the engine switch on (ACC).
    5. Connect an oscilloscope to terminals 34 (MCO+) and 35 (MCO-) of the T10 map light assembly connector.
    6. Check the waveform of the telephone microphone assembly using the oscilloscope.

      Result

      Result Proceed to
      A waveform synchronized with the voice input to the map light assembly is output A
      A waveform synchronized with the voice input to the map light assembly is not output B
      TEXT IN ILLUSTRATION

      *1 Component with harness connected
      (Map light assembly)

    B → See step   13 

    A → See step   12 

  12. PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE. Refer to  PROBLEM SYMPTOMS TABLE 
  13. REPLACE TELEPHONE MICROPHONE ASSEMBLY 
    1. Replace the telephone microphone assembly. Refer to REMOVAL .
    2. Check if the same malfunction recurs.

      Result

      Result Proceed to
      Malfunction does not recur
      (returns to normal)      		 A
      Malfunction recurs B

    B → See step   15 

    A → END 

  14. REPLACE RADIO RECEIVER ASSEMBLY. Refer to  REMOVAL 
  15. REPLACE MAP LIGHT ASSEMBLY. Refer to  REMOVAL 
  16. REPLACE DCM (TELEMATICS TRANSCEIVER). Refer to  REMOVAL 
scientia non olet · About LEMON Manuals