Problem Symptoms Table
HINT:
Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptom are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.
ENTIRE SYSTEM
| Symptom | Suspected Area | Reference |
|---|---|---|
| Entire combination meter assembly does not operate | Power source circuit | Refer to Entire Combination Meter does not Operate |
| Meter illumination is always dark | Meter illumination circuit | Refer to Meter Illumination is Always Dark |
| Meter illumination does not dim at night | Meter illumination circuit | Refer to Meter Illumination does not Dim at Night |
| Operating light control rheostat does not change light brightness | Light control rheostat circuit | Refer to Operating Light Control Rheostat does not Change Light Brightness |
METER OR GAUGE
| Symptom | Suspected Area | Reference |
|---|---|---|
| Speedometer malfunction | Speedometer circuit | Refer to Speedometer Malfunction |
| Tachometer malfunction | Tachometer circuit | Refer to Tachometer Malfunction |
| Fuel receiver gauge malfunction | Fuel receiver gauge circuit | Refer to Fuel Receiver Gauge Malfunction |
| Engine coolant temperature malfunction | Engine coolant temperature receiver gauge circuit | Refer to Engine Coolant Temperature Receiver Gauge Malfunction |
| ODO/TRIP meter malfunction | Combination meter assembly | Refer to Odo/Trip Switch Malfunction |
WARNING LIGHT OR INDICATOR LIGHT
| Symptom | Suspected Area | Reference |
|---|---|---|
| Turn indicator light malfunction | Harness or connector | - |
| Turn signal flasher assembly | Refer to ON-VEHICLE INSPECTION | |
| Combination meter assembly | Refer to REMOVAL | |
| Charge warning light does not come on | Perform Active Test (Indicat. Lamp Charge) | Refer to DATA LIST / ACTIVE TEST |
| Harness or connector | - | |
| Generator | Refer to INSPECTION | |
| Combination meter assembly | Refer to REMOVAL | |
| Open door warning light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Perform Active Test (Indicat. Lamp Doors All Open) | Refer to DATA LIST / ACTIVE TEST | |
| Front door courtesy switch | Refer to INSPECTION | |
| Rear door courtesy switch | Refer to INSPECTION | |
| Back door courtesy switch | Refer to INSPECTION | |
| Main body ECU | Refer to REMOVAL | |
| Combination meter assembly | Refer to REMOVAL | |
| RSCA OFF indicator light malfunction | Operation check | Refer to OPERATION CHECK |
| Harness or connector | - | |
| Center airbag assembly | Refer to REMOVAL | |
| Combination meter assembly | Refer to REMOVAL | |
| Multi-terrain select indicator light does not come on (w/ Multi-terrain Select) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Perform Active Test (OFF Road Guidance Indicator) | Refer to DATA LIST / ACTIVE TEST | |
| Vehicle stability control system | Refer to Multi-terrain Select Indicator Light does not Come ON | |
| Combination meter assembly | Refer to REMOVAL | |
| Multi-terrain select indicator light does not go off (w/ Multi-terrain Select) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Perform Active Test (OFF Road Guidance Indicator) | Refer to DATA LIST / ACTIVE TEST | |
| Vehicle stability control system | Refer to Multi-terrain Select Indicator Light Remains ON | |
| Combination meter assembly | Refer to REMOVAL | |
| CRAWL indicator light does not come on (w/ CRAWL Control) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Perform Active Test (Indicat. CRAWL) | Refer to DATA LIST / ACTIVE TEST | |
| Vehicle stability control system | Refer to Crawl Indicator Light does not Come ON | |
| Combination meter assembly | Refer to REMOVAL | |
| CRAWL indicator light does not go off (w/ CRAWL Control) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Perform Active Test (Indicat. CRAWL) | Refer to DATA LIST / ACTIVE TEST | |
| Vehicle stability control system | Refer to Crawl Indicator Light Remains ON | |
| Combination meter assembly | Refer to REMOVAL | |
| LDA indicator light malfunction (w/ Lane Departure Alert System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Perform Active Test (Drift From The Lane) | Refer to DATA LIST / ACTIVE TEST | |
| Lane departure alert system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Combination meter assembly | Refer to REMOVAL | |
| Kinetic dynamic suspension indicator light malfunction (w/ Kinetic Dynamic Suspension System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Perform Active Test (KDSS Indicator) | Refer to DATA LIST / ACTIVE TEST | |
| Kinetic dynamic suspension control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Combination meter assembly | Refer to REMOVAL | |
| 2nd start indicator light malfunction | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Perform Active Test (Indicat. 2nd START) | Refer to DATA LIST / ACTIVE TEST | |
| Automatic transmission system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Combination meter assembly | Refer to REMOVAL | |
| PCS indicator light malfunction (w/ Pre-collision System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Perform Active Test (Indicat. Precrash) | Refer to DATA LIST / ACTIVE TEST | |
| Pre-collision system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Combination meter assembly | Refer to REMOVAL | |
| ABS warning light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Perform Active Test (Indicat. Lamp ABS) | Refer to DATA LIST / ACTIVE TEST | |
| ABS warning light circuit | Refer to ABS Warning Light does not Come ON | |
| Combination meter assembly | Refer to REMOVAL | |
| ABS warning light does not go off | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Perform Active Test (Indicat. Lamp ABS) | Refer to DATA LIST / ACTIVE TEST | |
| ABS warning light circuit | Refer to ABS Warning Light Remains ON | |
| Combination meter assembly | Refer to REMOVAL | |
| Brake warning light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Perform Active Test (Indicat. Lamp Brake) | Refer to DATA LIST / ACTIVE TEST | |
| Brake warning light circuit | Refer to Brake Warning Light does not Come ON | |
| Combination meter assembly | Refer to REMOVAL | |
| Brake warning light does not go off | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Perform Active Test (Indicat. Lamp Brake) | Refer to DATA LIST / ACTIVE TEST | |
| Brake fluid level warning switch | - | |
| Brake warning light circuit | Refer to Brake Warning Light Remains ON | |
| Combination meter assembly | Refer to REMOVAL | |
| MIL (Malfunction Indicator Lamp) malfunction | Operation check | Refer to OPERATION CHECK |
| MIL Circuit | Refer to MIL Circuit | |
| Combination meter assembly | Refer to REMOVAL | |
| VSC OFF indicator light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Perform Active Test (Indicat. VSC OFF) | Refer to DATA LIST / ACTIVE TEST | |
| VSC OFF warning light circuit | Refer to VSC OFF Indicator Light does not Come ON | |
| Combination meter assembly | Refer to REMOVAL | |
| VSC OFF indicator light does not go off | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Perform Active Test (Indicat. VSC OFF) | Refer to DATA LIST / ACTIVE TEST | |
| VSC OFF warning light circuit | Refer to VSC OFF Indicator Light Remains ON | |
| Combination meter assembly | Refer to REMOVAL | |
| Slip indicator light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Perform Active Test (Indicat. Lamp Slip) | Refer to DATA LIST / ACTIVE TEST | |
| Slip indicator light circuit | Refer to Slip Indicator Light does not Come ON | |
| Combination meter assembly | Refer to REMOVAL | |
| Slip indicator light does not go off | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Perform Active Test (Indicat. Lamp Slip) | Refer to DATA LIST / ACTIVE TEST | |
| Slip indicator light circuit | Refer to Slip Indicator Light Remains ON | |
| Combination meter assembly | Refer to REMOVAL | |
| Downhill assist control indicator light does not come on (w/ Downhill Assist Control System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Perform Active Test (Indicat. Downhill Assist control) | Refer to DATA LIST / ACTIVE TEST | |
| Vehicle stability control system | Refer to Downhill Assist Control Indicator Light does not Come ON | |
| Combination meter assembly | Refer to REMOVAL | |
| Downhill assist control indicator light does not go off (w/ Downhill Assist Control System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Perform Active Test (Indicat. Downhill Assist control) | Refer to DATA LIST / ACTIVE TEST | |
| Vehicle stability control system | Refer to Downhill Assist Control Indicator Light Remains ON | |
| Combination meter assembly | Refer to REMOVAL | |
| Front fog indicator light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Perform Active Test (Indicat. Lamp Fr FOG) | Refer to DATA LIST / ACTIVE TEST | |
| Lighting system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Combination meter assembly | Refer to REMOVAL | |
| Tail indicator light does not come on (for Canada) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Perform Active Test (Indicat. Lamp Tail) | Refer to DATA LIST / ACTIVE TEST | |
| Main body ECU | Refer to REMOVAL | |
| Combination meter assembly | Refer to REMOVAL | |
| HEAD indicator light does not come on (for U.S.A.) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Perform Active Test (Indicat. Lamp Head) | Refer to DATA LIST / ACTIVE TEST | |
| Main body ECU | Refer to REMOVAL | |
| Combination meter assembly | Refer to REMOVAL | |
| Automatic high beam indicator light does not come on (w/ Automatic High Beam System) |
CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Perform Active Test (Automatic High Beam Indicator) | Refer to DATA LIST / ACTIVE TEST | |
| Lighting system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Combination meter assembly | Refer to REMOVAL | |
| Beam indicator light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Perform Active Test (Indicat. Lamp Beam) | Refer to DATA LIST / ACTIVE TEST | |
| Lighting system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Combination meter assembly | Refer to REMOVAL | |
| Driver side seat belt warning light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Perform Active Test (Driver Side Seat Belt) | Refer to DATA LIST / ACTIVE TEST | |
| Driver side seat belt warning light circuit | Refer to Driver Side Seat Belt Warning Light does not Operate | |
| Combination meter assembly | Refer to REMOVAL | |
| Master warning light does not come on | Perform Active Test (Master Warning) | Refer to DATA LIST / ACTIVE TEST |
| Combination meter assembly | Refer to REMOVAL | |
| SRS warning light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Perform Active Test (Indicat. Lamp Airbag) | Refer to DATA LIST / ACTIVE TEST | |
| SRS warning light circuit | Refer to SRS Warning Light does not Come ON | |
| Combination meter assembly | Refer to REMOVAL | |
| SRS warning light does not go off | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Perform Active Test (Indicat. Lamp Airbag) | Refer to DATA LIST / ACTIVE TEST | |
| SRS warning light circuit | Refer to SRS Warning Light Remains ON | |
| Combination meter assembly | Refer to REMOVAL | |
| Tire pressure warning light malfunction | Harness or connector | - |
| Perform Active Test (Indicat. Tire Pressure Warning System) | Refer to DATA LIST / ACTIVE TEST | |
| Tire pressure warning system | Refer to Tire Pressure Warning Light Circuit | |
| Combination meter assembly | Refer to REMOVAL | |
| Cruise set indicator light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Perform Active Test (Indicat. SET) | Refer to DATA LIST / ACTIVE TEST | |
| Cruise set indicator light circuit | Refer to Cruise SET Indicator Light Circuit | |
| Combination meter assembly | Refer to REMOVAL | |
| Eco driving indicator light malfunction | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Perform Active Test (Indicat. ECONO) | Refer to DATA LIST / ACTIVE TEST | |
| SFI system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Combination meter assembly | Refer to REMOVAL | |
| Cruise main indicator light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Perform Active Test (Indicat. Lamp Cruise) | Refer to DATA LIST / ACTIVE TEST | |
| Cruise main indicator light circuit | Refer to Cruise Main Indicator Light Circuit | |
| Combination meter assembly | Refer to REMOVAL | |
| Radar cruise indicator light does not come on (w/ Dynamic Radar Cruise Control System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Perform Active Test (Indicat. Rader Cruise) | Refer to DATA LIST / ACTIVE TEST | |
| Radar cruise indicator light circuit | Refer to Cruise Main Indicator Light Circuit | |
| Driving support ECU | Refer to REMOVAL | |
| Combination meter assembly | Refer to REMOVAL | |
| Clearance sonar indicator light malfunction (w/ Intuitive Parking Assist System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Perform Active Test (Indicat. INTUITIVE P/A LCD) | Refer to DATA LIST / ACTIVE TEST | |
| Intuitive parking assist system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Clearance warning ECU | Refer to REMOVAL | |
| Combination meter assembly | Refer to REMOVAL | |
| AFS OFF indicator light malfunction (w/ AFS) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Perform Active Test (Indicat. AFS) | Refer to DATA LIST / ACTIVE TEST | |
| Lighting system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Combination meter assembly | Refer to REMOVAL | |
| Fuel level warning light does not come on | Perform Active Test (Indicat. Lamp Fuel) | Refer to DATA LIST / ACTIVE TEST |
| Harness or connector | - | |
| Fuel sender gauge assembly | Refer to REMOVAL | |
| Combination meter assembly | Refer to REMOVAL | |
| A/T shift indicator light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Perform Active Test (A/T Indicator Operation 1, A/T Indicator Operation 2) | Refer to DATA LIST / ACTIVE TEST | |
| Park/neutral position switch circuit | Refer to INSPECTION | |
| SFI system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Combination meter assembly | Refer to REMOVAL | |
| Center differential lock indicator light malfunction | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Perform Active Test (Indicat. Ctr DIFF LOCK) | Refer to DATA LIST / ACTIVE TEST | |
| Transfer system | - | |
| Combination meter assembly | Refer to REMOVAL | |
| 4LO indicator light malfunction | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Perform Active Test (Indicat. 4LO) | Refer to DATA LIST / ACTIVE TEST | |
| Transfer system | - | |
| Combination meter assembly | Refer to REMOVAL |
CRUISE INFORMATION DISPLAY
| Symptom | Suspected Area | Reference |
|---|---|---|
| Current fuel consumption display malfunction | Vehicle stability control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| SFI system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Combination meter assembly | Refer to REMOVAL | |
| Average fuel consumption display | Vehicle stability control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| SFI system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Combination meter assembly | Refer to REMOVAL | |
| Average fuel consumption after refueling display malfunction | Vehicle stability control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| SFI system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Fuel sender gauge assembly | Refer to REMOVAL | |
| Combination meter assembly | Refer to REMOVAL | |
| Cruising range display malfunction | Vehicle stability control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| SFI system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Fuel sender gauge assembly | Refer to REMOVAL | |
| Combination meter assembly | Refer to REMOVAL | |
| Average vehicle speed display malfunction | Vehicle stability control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| SFI system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Multi-function switch (Steering pad switch assembly) | Refer to INSPECTION | |
| Driving support switch control ECU | Refer to REMOVAL | |
| Combination meter assembly | Refer to REMOVAL | |
| Elapsed time display malfunction | SFI system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Multi-function switch (Steering pad switch assembly) | Refer to INSPECTION | |
| Combination meter assembly | Refer to REMOVAL | |
| Operating multi-function switch does not change multi-information display | Multi-function switch (Steering pad switch assembly) | Refer to INSPECTION |
| Harness or connector | - | |
| LIN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Driving support switch control ECU | Refer to REMOVAL | |
| Combination meter assembly | Refer to REMOVAL |
MULTI-INFORMATION DISPLAY
| Symptom | Suspected Area | Reference |
|---|---|---|
| Multi-information display does not light up (combination meter operates normally) | Combination meter assembly | Refer to REMOVAL |
| Multi-information display malfunction (all warning displays come on, cruise information display does not come on) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Combination meter assembly | Refer to REMOVAL | |
| Brightness setting display malfunction | Light control rheostat | Refer to INSPECTION |
| Combination meter assembly | Refer to REMOVAL | |
| Multi-terrain select setting display malfunction (w/ Multi-terrain Select) | Vehicle stability control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Multi-function switch (Steering pad switch assembly) | Refer to INSPECTION | |
| Driving support switch control ECU | Refer to REMOVAL | |
| Combination meter assembly | Refer to REMOVAL | |
| "Adjusting LDA camera" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Lane Departure Alert System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Driving support ECU | Refer to REMOVAL | |
| Lane recognition camera sensor assembly | Refer to REMOVAL | |
| Combination meter assembly | Refer to REMOVAL | |
| "Adjusting front radar beam" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Dynamic Radar Cruise Control System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Dynamic radar cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Combination meter assembly | Refer to REMOVAL | |
| "Checking cruise control C/D" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Dynamic Radar Cruise Control System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Dynamic radar cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Combination meter assembly | Refer to REMOVAL | |
| "Checking cruise control brake" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Dynamic Radar Cruise Control System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Dynamic radar cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Combination meter assembly | Refer to REMOVAL | |
| "Brake!" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Pre-collision System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Pre-collision system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Combination meter assembly | Refer to REMOVAL | |
| "<!>"message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Pre-collision system (w/ Pre-collision System) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Dynamic radar cruise control system (w/ Dynamic Radar Cruise Control System) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Combination meter assembly | Refer to REMOVAL | |
| Door open display malfunction | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Main body ECU | Refer to REMOVAL | |
| Combination meter assembly | Refer to REMOVAL | |
| Steering angle display malfunction | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Vehicle stability control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Steering angle sensor (Spiral cable sub-assembly) | Refer to INSPECTION | |
| Combination meter assembly | Refer to REMOVAL | |
| "Auto power off to conserve battery" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Smart access system with push-button start | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Combination meter assembly | Refer to REMOVAL | |
| "Shift to P position" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Main body ECU | Refer to REMOVAL | |
| Park/neutral position switch circuit | Refer to INSPECTION | |
| Combination meter assembly | Refer to REMOVAL | |
| "Release parking brake" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Main body ECU | Refer to REMOVAL | |
| Parking brake switch | Refer to INSPECTION | |
| Combination meter assembly | Refer to REMOVAL | |
| "Key not detected" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Smart access system with push-button start | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Combination meter assembly | Refer to REMOVAL | |
| "Clean radar sensor" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Dynamic Radar Cruise Control System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Dynamic radar cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Combination meter assembly | Refer to REMOVAL | |
| "Cruise control not available" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Dynamic Radar Cruise Control System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Dynamic radar cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Combination meter assembly | Refer to REMOVAL | |
| "Check cruise control system" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Dynamic radar cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Combination meter assembly | Refer to REMOVAL | |
| "Check PCS system" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Pre-collision System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Pre-collision system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Combination meter assembly | Refer to REMOVAL | |
| "Check LDA system" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Lane Departure Alert System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Driving support ECU | Refer to REMOVAL | |
| Lane recognition camera sensor assembly | Refer to REMOVAL | |
| Combination meter assembly | Refer to REMOVAL | |
| "Check steering lock system" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Smart access system with push-button start | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Combination meter assembly | Refer to REMOVAL | |
| "Engine oil pressure low" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | Oil pressure switch assembly | Refer to REMOVAL |
| Combination meter assembly | Refer to REMOVAL | |
| "High transmission fluid temperature" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | Automatic transmission system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Combination meter assembly | Refer to REMOVAL | |
| "Turn power off" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Smart access system with push-button start | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Combination meter assembly | Refer to REMOVAL | |
| "Shift to P range and push engine switch to turn power off" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Park/neutral position switch circuit | Refer to INSPECTION | |
| Smart access system with push-button start | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Combination meter assembly | Refer to REMOVAL | |
| "Key detected in vehicle" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Smart access system with push-button start | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Combination meter assembly | Refer to REMOVAL | |
| "Moon roof open" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Sliding Roof System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Sliding roof system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Combination meter assembly | Refer to REMOVAL | |
| "Depress brake pedal touch engine switch with key" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Smart access system with push-button start | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Stop light switch | Refer to INSPECTION | |
| Combination meter assembly | Refer to REMOVAL | |
| "Depress brake pedal, and push engine switch to start" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Smart access system with push-button start | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Combination meter assembly | Refer to REMOVAL | |
| "Shift to P position to start" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Smart access system with push-button start | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Park/neutral position switch circuit | Refer to INSPECTION | |
| Combination meter assembly | Refer to REMOVAL | |
| "Steering lock active" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Smart access system with push-button start | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Combination meter assembly | Refer to REMOVAL | |
| "Key battery low" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Smart access system with push-button start | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Combination meter assembly | Refer to REMOVAL | |
| "Check sonar" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Intuitive Parking Assist System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Intuitive parking assist system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Combination meter assembly | Refer to REMOVAL | |
| "Clean sonar" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Intuitive Parking Assist System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Intuitive parking assist system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Combination meter assembly | Refer to REMOVAL | |
| "Low washer fluid" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | Level warning switch assembly | Refer to REMOVAL |
| Combination meter assembly | Refer to REMOVAL | |
| "TRC OFF" or "TRAC OFF" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Vehicle stability control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Combination meter assembly | Refer to REMOVAL | |
| "Oil Maintenance Required Soon" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | Combination meter assembly | Refer to REMOVAL |
| "Oil Maintenance Required" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | Combination meter assembly | Refer to REMOVAL |
| "Oil Maintenance Required Reset" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | Combination meter assembly | Refer to REMOVAL |
| "Oil Maintenance Reset Complete" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | Combination meter assembly | Refer to REMOVAL |
| "Oil Maintenance Reset Unfinished" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | Combination meter assembly | Refer to REMOVAL |
| "LDA not available" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Lane Departure Alert System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Driving support ECU | Refer to REMOVAL | |
| Lane recognition camera sensor assembly | Refer to REMOVAL | |
| Combination meter assembly | Refer to REMOVAL | |
| "PCS not available temporarily" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Pre-collision System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Pre-collision system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Combination meter assembly | Refer to REMOVAL | |
| "CRAWL has been deactivated" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ CRAWL Control) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Vehicle stability control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Combination meter assembly | Refer to REMOVAL | |
| "CRAWL is activated" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ CRAWL Control) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Vehicle stability control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Combination meter assembly | Refer to REMOVAL | |
| "CRAWL not available Select L4 and shift to "D" or "R" position" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ CRAWL Control) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Vehicle stability control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Combination meter assembly | Refer to REMOVAL | |
| "CRAWL not available Check system operation conditions" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ CRAWL Control) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Vehicle stability control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Combination meter assembly | Refer to REMOVAL | |
| "Check air suspension system" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Air Suspension System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Air suspension system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Combination meter assembly | Refer to REMOVAL | |
| Eco driving indicator zone display malfunction | Combination meter assembly (Eco driving indicator zone display setting) | Refer to INITIALIZATION |
| CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| SFI system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Combination meter assembly | Refer to REMOVAL | |
| Air suspension indicator display malfunction (w/ Air Suspension System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Air suspension system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Combination meter assembly | Refer to REMOVAL | |
| "Shift to L4" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Multi-terrain Select) | Vehicle stability control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Driving support switch control ECU | Refer to REMOVAL | |
| Combination meter assembly | Refer to REMOVAL | |
| "Stop the vehicle and shift the automatic transmission to N" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Multi-terrain Select) | Vehicle stability control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Park/neutral position switch circuit | Refer to INSPECTION | |
| Driving support switch control ECU | Refer to REMOVAL | |
| Combination meter assembly | Refer to REMOVAL | |
| "Push center differential lock/unlock switch" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Multi-terrain Select) | Transfer system | - |
| Vehicle stability control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Driving support switch control ECU | Refer to REMOVAL | |
| Combination meter assembly | Refer to REMOVAL | |
| "Multi-terrain select not available" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Multi-terrain Select) | Vehicle stability control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Driving support switch control ECU | Refer to REMOVAL | |
| Combination meter assembly | Refer to REMOVAL | |
| "Return the four-wheel drive control switch" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Multi-terrain Select) | Vehicle stability control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Combination meter assembly | Refer to REMOVAL | |
| "Accelerate or Decelerate" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Multi-terrain Select) | Vehicle stability control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Driving support switch control ECU | Refer to REMOVAL | |
| Combination meter assembly | Refer to REMOVAL | |
| "Operation not possible when multi-terrain select activated" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Multi-terrain Select) | Vehicle stability control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Driving support switch control ECU | Refer to REMOVAL | |
| Combination meter assembly | Refer to REMOVAL | |
| "Operation not possible when CRAWL control activated" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Multi-terrain Select) | Vehicle stability control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Driving support switch control ECU | Refer to REMOVAL | |
| Combination meter assembly | Refer to REMOVAL | |
| "Multi-terrain select has been cancelled" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Multi-terrain Select) | Vehicle stability control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Driving support switch control ECU | Refer to REMOVAL | |
| Combination meter assembly | Refer to REMOVAL | |
| "Drive the vehicle a short distance" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Multi-terrain Select) | Vehicle stability control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Driving support switch control ECU | Refer to REMOVAL | |
| Combination meter assembly | Refer to REMOVAL | |
| Intuitive parking assist system display malfunction (w/ Intuitive Parking Assist System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Parking assist ECU (w/ Side Monitor System) | Refer to REMOVAL | |
| Clearance warning ECU (w/o Side Monitor System) | Refer to REMOVAL | |
| Combination meter assembly | Refer to REMOVAL | |
| Customize setting display malfunction | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Multi-function switch (Steering pad switch assembly) | Refer to INSPECTION | |
| Driving support switch control ECU | Refer to REMOVAL | |
| Main body ECU | Refer to REMOVAL | |
| Combination meter assembly | Refer to REMOVAL |
BUZZER
| Symptom | Suspected Area | Reference |
|---|---|---|
| Seat belt warning buzzer does not operate | Seat belt warning buzzer ON/OFF setting | Refer to CUSTOMIZE PARAMETERS |
| Combination meter assembly | Refer to REMOVAL | |
| Sliding roof open warning buzzer does not operate (w/ Sliding Roof System) | Sliding roof system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Combination meter assembly | Refer to REMOVAL | |
| Dynamic radar cruise control low speed cancel buzzer does not operate (w/ Dynamic Radar Cruise Control System) | Dynamic radar cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Combination meter assembly | Refer to REMOVAL | |
| Dynamic radar cruise control warning buzzer does not operate (w/ Dynamic Radar Cruise Control System) | Dynamic radar cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Combination meter assembly | Refer to REMOVAL | |
| Engine immobilizer certification buzzer does not operate | Engine immobilizer system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Automatic transmission system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Combination meter assembly | Refer to REMOVAL | |
| 4WD buzzer does not operate | Transfer system | - |
| Combination meter assembly | Refer to REMOVAL | |
| Driving with any door opened warning buzzer does not operate | Main body ECU | Refer to REMOVAL |
| Combination meter assembly | Refer to REMOVAL | |
| PKB-ON driving warning buzzer does not operate | Parking brake switch assembly | Refer to REMOVAL |
| Main body ECU | Refer to REMOVAL | |
| Combination meter assembly | Refer to REMOVAL | |
| Smart access system with push-button start warning buzzer does not operate (w/ Smart Access System with Push-button Start) | Smart access system with push-button start | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Combination meter assembly | Refer to REMOVAL | |
| Multi-information display warning buzzer does not operate | Combination meter assembly | Refer to REMOVAL |
OTHERS
| Symptom | Suspected Area | Reference |
|---|---|---|
| Passenger side seat belt warning light does not come on | Perform Active Test (Front Passenger Side Seat Belt) | Refer to DATA LIST / ACTIVE TEST |
| Passenger side seat belt warning light circuit | Refer to Front Passenger Side Seat Belt Warning Light Malfunction | |
| Combination meter assembly | Refer to REMOVAL | |
| Other systems that use speed signal do not operate normally | Speed signal circuit | Refer to Speed Signal Circuit |
| Customizable parameters cannot be changed (customizable parameters can be changed by using Techstream) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Multi-function switch (Steering pad switch assembly) | Refer to INSPECTION | |
| Driving support switch control ECU | Refer to REMOVAL | |
| Main body ECU | Refer to REMOVAL | |
| Combination meter assembly | Refer to REMOVAL |