LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2009 >> LS 600hL >> Repair and Diagnosis >> Hybrid/Electric Powertrain >> Testing and Diagnosis >> Hybrid Vehicle Control (Diagnostic Codes (P0A10-592 - P0A7A-322)) >> Hybrid Control System >> DTC P0A2C-247: Drive Motor "A" Temperature Sensor Circuit Low; DTC P0A2D-249: Drive Motor "A" Temperature Sensor Circuit High >> Procedure

DTC P0A2C-247: Drive Motor "A" Temperature Sensor Circuit Low; DTC P0A2D-249: Drive Motor "A" Temperature Sensor Circuit High: Procedure

  1. CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR) 
    1. Check the connections of the hybrid vehicle control ECU connectors.
      Fig 1: Identifying Hybrid Vehicle Control ECU Connectors
      GTY147636Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      OK

      The connectors are connected securely and there are no contact problems.

    NG → CONNECT SECURELY 

    OK: Go to next step 

  2. READ VALUE USING TECHSTREAM (MOTOR TEMP NO1) 
    1. Connect the Techstream to the DLC3.
    2. Turn the power switch on (IG).
    3. Select the following menu items: Powertrain / Hybrid Control / Data List / Motor Temp No1.
    4. Read the data list.

      Result

      Result Proceed to
      -58°F (-50°C) A
      401°F (205°C) B
      Same as actual temperature C

    C → See step   9 

    B → See step   5 

    A: Go to next step 

  3. READ VALUE USING TECHSTREAM (CHECK FOR OPEN) 
    1. Turn the power switch off.
    2. Disconnect the motor temperature sensor connector.
      Fig 2: Identifying E60 Connector Terminals
      GTY148456Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Connect terminals 4 (MMT) and 8 (MMTG) of the vehicle side connector of the motor temperature sensor.
    4. Turn the power switch on (IG).
    5. Select the following menu items: Powertrain / Hybrid Control / Data List / Motor Temp No1.
    6. Read the data list.

      OK

      Tester Display Condition Specified Condition
      Motor Temp No1 Terminals MMT and MMTG connected.
      Power switch on (IG)      		 401°F (205°C)

    NG → See step   4 

    OK → See step   8 

  4. CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - MOTOR TEMPERATURE SENSOR) 
    1. Turn the power switch off.
    2. Connect terminals 23 (MMT) and 22 (MMTG) of the connector E 55 of hybrid vehicle control ECU.
      Fig 3: Identifying E55 Connector Terminals
      GTY147661Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Turn the power switch on (IG).
    4. Select the following menu items: Powertrain / Hybrid Control / Data List / Motor Temp No1.
    5. Read the data list.

      OK

      Tester Display Condition Specified Condition
      Motor Temp No1 Terminals MMT and MMTG connected.
      Power switch on (IG)      		 401°F (205°C)

    NG → REPAIR OR REPLACE HARNESS OR CONNECTOR 

    OK → See step   7 

  5. READ VALUE USING TECHSTREAM (CHECK FOR SHORT) 
    1. Turn the power switch off.
    2. Disconnect the motor temperature sensor connector.
    3. Turn the power switch on (IG).
    4. Select the following menu items: Powertrain / Hybrid Control / Data List / Motor Temp No1.
    5. Read the data list.

      OK

      Tester Display Switch Condition Specified Condition
      Motor Temp No1 Power switch on (IG) 58°F (-50°C)

    NG → See step   6 

    OK → See step   8 

  6. CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - MOTOR TEMPERATURE SENSOR) 
    1. Turn the power switch off.
    2. Disconnect connector E55 from the hybrid vehicle control ECU.
    3. Measure the resistance according to the value(s) in the table below.
      Fig 4: Checking Harness And Connector (Hybrid Vehicle Control ECU -- Motor Temperature Sensor)
      GTY147726Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard resistance (Check for open)

      Tester Connection Switch Condition Specified Condition
      E55-23 (MMT) - E60-4 (MMT) Power switch off Below 1 Ω
      E55-22 (MMTG) - E60-8 (MMTG) Power switch off Below 1 Ω

      Standard resistance (Check for short)

      Tester Connection Switch Condition Specified Condition
      E55-23 (MMT) or E60-4 (MMT) - Body ground and other terminals Power switch off 10 kΩ or higher
      E55-22 (MMTG) or E60-8 (MMTG) - Body ground and other terminals Power switch off 10 kΩ or higher

    NG → REPAIR OR REPLACE HARNESS OR CONNECTOR 

    OK → See step   7 

  7. REPLACE HYBRID VEHICLE CONTROL ECU. Refer to  REMOVAL  . 
  8. REPLACE HYBRID VEHICLE TRANSMISSION ASSEMBLY. Refer to  REMOVAL 
  9. CHECK FOR INTERMITTENT PROBLEMS. Refer to  CHECK FOR INTERMITTENT PROBLEMS 
scientia non olet · About LEMON Manuals