LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2008 >> RX 400h FWD >> Repair and Diagnosis >> Body & Frame >> Exterior/Interior Trim >> Interior >> Roof Headlining >> Removal

Roof Headlining: Removal

  1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 
  2. REMOVE TONNEAU COVER ASSEMBLY 
  3. REMOVE DECK BOARD SUB-ASSEMBLY 
    1. Disengage the 5 clips and turn up the front side of the deck board.
    2. Remove the 2 bolts and deck board sub-assembly.
      Fig 1: Removing Deck Board Sub-Assembly
      G05281727Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  4. REMOVE DECK FLOOR BOX FRONT 
    1. Using a clip remover, remove the 2 clips and deck floor box front.
      Fig 2: Identifying Deck Floor Box Front Clips
      G05281728Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  5. REMOVE DECK FLOOR BOX REAR 
    1. Using a clip remover, remove the 2 clips and deck floor box rear.
      Fig 3: Identifying Deck Floor Box Rear Clips
      G05281729Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  6. REMOVE DECK NO. 3 BOARD SUB-ASSEMBLY 
    1. Remove the 2 bolts, 2 nuts and deck No. 3 board sub-assembly.
      Fig 4: Identifying Deck No. 3 Board Sub-Assembly Bolts And Nuts
      G05281730Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  7. REMOVE DECK NO. 2 BOARD SUB-ASSEMBLY 
    1. Remove the 4 blots, 2 nuts and deck No. 2 board sub-assembly.
      2. Fig 5: Identifying Deck No. 2 Board Sub-Assembly Bolts And Nuts
      G05281731Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  8. REMOVE BACK DOOR WEATHERSTRIP 
  9. REMOVE REAR FLOOR FINISH PLATE 
    1. Using a clip remover, remove the 2 clips.
    2. Disengage the 2 claws and 6 clips, and remove the rear floor finish plate.
  10. REMOVE JACK CARRIER ASSEMBLY 
    1. Remove the jack carrier support, jack assembly and jack carrier assembly.
      Fig 6: Removing Rear Floor Finish Plate
      G05281732Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  11. REMOVE DECK SIDE TRIM LH BOX 
    1. Remove the clip (A).
    2. Using a clip remover, remove the clip (B) and deck side trim box.
      3. Fig 7: Identifying Deck Side Trim Box Clip
      G05281733Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  12. REMOVE DECK SIDE TRIM RH BOX 
  13. REMOVE REAR SEAT TRACK BRACKET COVER  (See REMOVAL )
  14. REMOVE REAR SEAT ASSEMBLY LH  (See REMOVAL )
  15. REMOVE REAR SEAT TRACK BRACKET COVER  (See REMOVAL )
  16. REMOVE REAR SEAT ASSEMBLY RH  (See REMOVAL )
  17. REMOVE FRONT DOOR SCUFF LH PLATE 
    1. Disengage the 6 claws and 4 clips, and remove the front door scuff plate.
    2. Disconnect the connector, (w/ illumination scuff plate)
      3. Fig 8: Identifying Front Door Scuff Plate Claws And Clips
      G05281734Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  18. REMOVE FRONT DOOR SCUFF RH PLATE 
  19. REMOVE FRONT DOOR OPENING TRIM LH WEATHERSTRIP 
  20. REMOVE FRONT DOOR OPENING TRIM RH WEATHERSTRIP 
  21. REMOVE REAR DOOR SCUFF LH PLATE 
    1. Disengage the 4 claws and 2 clips, and remove the rear door scuff plate.
    2. Disconnect the connector, (w/ illumination scuff plate)
      3. Fig 9: Identifying Rear Door Scuff Plate Claws And Clips
      G05281735Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  22. REMOVE REAR DOOR SCUFF RH PLATE 
  23. REMOVE REAR DOOR OPENING TRIM LH WEATHERSTRIP 
  24. REMOVE REAR DOOR OPENING TRIM RH WEATHERSTRIP 
  25. REMOVE FRONT PILLAR LH GARNISH 
    1. Detach clip (A) from the vehicle body. Pull the pillar garnish so that the tip of clip (B) locks in the pillar garnish hole.
    2. Using needle-nose pliers, rotate clip (B) 90°.
    3. Disengage the 2 claws and remove the front pillar garnish.
    4. Remove clip (B).
      Fig 10: Identifying Front Pillar Garnish Claws And Clips
      G05281736Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Protect the curtain shield airbag assembly.
      1. Thoroughly cover the airbag with a cloth or nylon sheet that is 700 mm (27.56 in.) x 120 mm (4.72 in.) and fix the ends of the cover with adhesive tape, as shown in the illustration.
        NOTE: Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.
        2. Fig 11: Identifying Adhesive Applying Area
        G05281737Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  26. REMOVE FRONT PILLAR RH GARNISH 
  27. REMOVE LAP BELT OUTER ANCHOR COVER 
    1. Disengage the 2 claws and remove the lap belt outer anchor, as shown in the illustration.

      HINT:

      Use the same procedure to remove the other side.

      Fig 12: Removing Lap Belt Outer Anchor Cover
      G05281738Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  28. SEPARATE FRONT SEAT OUTER LH BELT ASSEMBLY 
    1. Remove the bolt and separate the front seat outer LH belt assembly.
      2. Fig 13: Identifying Front Seat Outer LH Belt Assembly With Bolt
      G05281739Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  29. SEPARATE FRONT SEAT OUTER RH BELT ASSEMBLY 
  30. REMOVE CENTER PILLAR LH GARNISH LOWER 
    1. Disengage the 3 claws and 2 clips, and remove the center pillar garnish lower.
      2. Fig 14: Identifying Center Pillar Garnish Lower Claws And Clips
      G05281740Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  31. REMOVE CENTER PILLAR RH GARNISH LOWER 
  32. REMOVE CENTER PILLAR LH GARNISH 
    1. Remove the 2 screws.
    2. Disengage the clip and remove the center pillar garnish by pulling it down.
      3. Fig 15: Removing Center Pillar LH Garnish
      G05281741Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  33. REMOVE CENTER PILLAR RH GARNISH 
  34. REMOVE DECK SIDE TRIM LH COVER 
    1. Using a molding remover, disengage 3 claws (A).
    2. Disengage 2 claws (8) and remove the deck side trim cover by pulling it to inside the vehicle.
  35. REMOVE DECK SIDE TRIM RH COVER 
  36. SEPARATE REAR NO. 1 SEAT OUTER LH BELT ASSEMBLY 
    1. Remove the bolt and separate the rear No. 1 seat outer belt assembly.
      Fig 16: Identifying Deck Side Trim LH Cover Claws
      G05281742Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  37. SEPARATE REAR NO. 1 SEAT OUTER RH BELT ASSEMBLY 
  38. REMOVE REAR SEAT SIDE LH COVER 
    1. Using a clip remover, remove the 3 clips.
    2. Disengage the 4 clips and remove the rear seat side cover.
      3. Fig 17: Identifying Rear Seat Side Cover Clips
      G05281743Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  39. REMOVE REAR SEAT SIDE RH COVER 
  40. REMOVE REAR FLOOR FINISH SIDE LH PLATE 
    1. Using a clip remover, remove the clip.
    2. Disengage the 2 clips and remove the rear floor finish side plate.
  41. REMOVE REAR FLOOR FINISH SIDE RH PLATE 
  42. REMOVE ROPE HOOK 
    1. Remove the 2 bolts and 2 rope hooks.

      HINT:

      Use the same procedure to remove the other side.

      Fig 18: Identifying Rear Floor Finish Side Plate Clips
      G05281744Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  43. REMOVE DECK TRIM SIDE LH PANEL ASSEMBLY 
    1. Using a clip remover, remove the 4 clips.
    2. Disengage the 2 clips and remove the deck trim side panel assembly.
      3. Fig 19: Identifying Deck Trim Side Panel Assembly With Clips
      G05281745Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  44. REMOVE DECK TRIM SIDE RH PANEL ASSEMBLY 
  45. REMOVE ROOM LIGHT ASSEMBLY NO. 2 
    1. Using a screwdriver, disengage the claw and remove the room light assembly No. 2.

      HINT:

      Tape the screwdriver tip before use.

    2. Disconnect the connector.
      Fig 20: Identifying Room Light Assembly No. 2 Claw
      G05281746Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  46. REMOVE ROOF SIDE LH GARNISH ASSEMBLY INNER 
    1. Using a screwdriver, remove the tonneau cover holder cap.

      HINT:

      Tape the screwdriver tip before use.

    2. Remove the 3 bolts.
    3. Using a clip remover, remove the 3 clips.
      Fig 21: Identifying Tonneau Cover Holder Cap Bolts And Clips
      G05281747Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Disengage the 7 clips and remove the roof side garnish assembly inner.
      Fig 22: Identifying Roof Side Garnish Assembly Inner Clips
      G05281748Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Disengage the 4 claws and separate the seat belt bezel.
      6. Fig 23: Identifying Seat Belt Bezel Claws
      G05281749Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  47. REMOVE ROOF SIDE RH GARNISH ASSEMBLY INNER 
  48. REMOVE TELEVISION BASE (w/ Rear Seat Entertainment System)  (See REMOVAL )
  49. REMOVE TELEVISION DISPLAY ASSEMBLY (w/ Rear Seat Entertainment System)  (See REMOVAL )
  50. REMOVE ASSIST GRIP SUB-ASSEMBLY 
    1. Using a screwdriver, disengage the 3 claws and remove the 2 assist grip covers.

      HINT:

      Tape the screwdriver tip before use.

    2. Remove the 2 screws and assist grip sub-assembly.

      HINT:

      Use the same procedure for the other 3 assist grips.

      Fig 24: Disengaging Assist Grip Sub-Assembly Claws
      G05281750Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  51. REMOVE RAIN SENSOR (w/ Rain Sensor)  (See REMOVAL )
  52. REMOVE ROOM LIGHT ASSEMBLY NO. 1 
    1. Using a screwdriver, disengage the 4 claws and remove the lens cover.

      HINT:

      Tape the screwdriver tip before use.

      Fig 25: Disengaging Room Light Assembly No. 1 Claws
      G05205616Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Using a screwdriver, disengage the 2 springs, as shown in the illustration.

      HINT:

      Tape the screwdriver tip before use.

    3. Disengage the 2 claws and remove the room light assembly No. 1.
    4. Disconnect the connector.
      Fig 26: Disengaging Springs
      G05205617Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  53. REMOVE MAP LIGHT ASSEMBLY 
    1. w/o Sliding roof:

      Using a screwdriver, disengage the 6 claws and remove the lens cover.

      HINT:

      Tape the screwdriver tip before use.

      Fig 27: Disengaging Map Light Assembly Claws (W/O Sliding Roof)
      G05281753Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. w/ Sliding roof:

      Using a screwdriver, disengage the 8 claws and remove the lens cover.

      HINT:

      Tape the screwdriver tip before use.

      Fig 28: Disengaging Map Light Assembly Claws (W/ Sliding Roof)
      G05281754Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Using a screwdriver, disengage the claws and open the 2 caps, as shown in the illustration.

      HINT:

      Tape the screwdriver tip before use.

      Fig 29: Disengaging Claws
      G05281755Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Remove the 4 screws and map light.
    5. Disconnect the connector.
      Fig 30: Identifying Map Light Screws
      G05281756Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  54. REMOVE LH VISOR ASSEMBLY 
    1. Using a molding remover, disengage the 4 claws and remove the visor bracket cover.
    2. Remove the 2 screws and visor assembly.
    3. Disconnect the connector.
      4. Fig 31: Identifying LH Visor Assembly Claws
      G05281757Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  55. REMOVE RH VISOR ASSEMBLY 
  56. REMOVE VISOR HOLDER 
    1. Remove the visor holder by turning it counterclockwise.

      HINT:

      Use the same procedure to remove the other side.

  57. REMOVE ROOF HEADLINING ASSEMBLY 
    1. Disconnect the roof wire connector and disengage the clamps from the front pillar LH.
    2. Disconnect the washer hose. Remove the bolt and disconnect the radio antenna cord connector and disengage the clamps from the front pillar RH.
      Fig 32: Removing Visor Holder
      G05244295Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Disconnect the washer hose. Disconnect the radio antenna cord connector and disengage the clamps from the rear quarter pillar RH.
    4. Disconnect the sliding roof drive gear connector, (w/ sliding roof)
    5. Remove the sunroof opening trim molding, (w/ sliding roof)
    6. Disengage the 2 fasteners and 3 clips, (w/o sliding roof)
    7. Disengage the 3 clips, (w/ sliding roof)
      Fig 33: Identifying Roof Headlining Assembly With Fastener
      G05281759Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    8. Remove the roof headlining from the vehicle through the back door side.
  58. REMOVE ROOF WIRE AND RADIO ANTENNA CORD 
    1. Remove the roof wire, radio antenna cord and washer hose from the roof headlining assembly.
      Fig 34: Identifying Radio Antenna Cord And Washer Hose With Roof Wire
      G05281760Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
scientia non olet · About LEMON Manuals