Front Wiper Motor: Installation

INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY
1. Using a T30 "TORX" socket, install the wiper motor with the 2 screws.
  Torque: 7.5 N*m (76 kgf*cm, 66 in.*lbf)
2. Apply MP grease to the crank arm pivot of the windshield wiper motor assembly.
  
  Fig 1: Locating Wiper Motor Screws
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Install the link to the wiper motor.
  
  Fig 2: Installing Link To Wiper Motor
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
4. Install the link to the wiper motor.
  
  Fig 3: Installing Link To Wiper Motor
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
5. Install the wiper motor cover with the clamp.
Fig 4: Locating Wiper Motor Cover With Clamp
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL WINDSHIELD WIPER MOTOR AND LINK
1. Slide the windshield wiper motor and link assembly as shown in the illustration so that the pin fits into place, and then install the windshield wiper motor and link assembly with the 3 bolts.
  Torque: 7.0 N*m (71 kgf*cm, 62 in.*lbf)
2. Connect the connector, attach the clamp and install the wire harness to the cowl top panel.
Fig 5: Locating Wiper Motor And Link Assembly Bolts
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY
1. Push in the ventilator louver to attach the 17 claws and install the ventilator louver.
2. Install the 2 clips.
  
  Fig 6: Identifying Ventilator Louver Claws
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Connect the washer hose.
Fig 7: Locating Washer Hose
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL HOOD TO COWL TOP SEAL
1. Attach the 12 clips and 4 clamps to install the hood to cowl top seal.
Fig 8: Identifying Hood Clips And Clamps
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL FRONT FENDER MAIN SEAL LH
1. Attach the 3 clips to install the fender main seal.
INSTALL FRONT FENDER MAIN SEAL RH
HINT:

Use the same procedures described for the LH side.
INSTALL UPPER RADIATOR SUPPORT SEAL (See INSTALLATION )
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
NOTE: When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See INITIALIZATION ).
INSTALL ENGINE ROOM SIDE COVER LH (See INSTALLATION )
INSTALL ENGINE ROOM SIDE COVER RH (See INSTALLATION )

INSTALL FRONT WIPER ARM LH

Stop the wiper motor at the automatic stop position.
Clean the wiper pivot serrations with a wire brush.

Fig 10: Cleaning Wiper Pivot Serrations With A Wire Brush
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
Install the wiper arm and blade with the nut. Make sure that the wiper arm and blade come to the position shown in the illustration.

Standard Measurement

MEASUREMENT CONDITION

Position	Specified Condition
A	16.8 to 36.8 mm (0.661 to 1.45 in.)

Torque: 25 N*m (255 kgf*cm, 18 ft.*lbf)

HINT:

Hold down the wiper arm hinge with your hand while tightening the nut.

Fig 11: Identifying Blade Position

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

INSTALL FRONT WIPER ARM RH

Stop the wiper motor at the automatic stop position.
Clean the wiper pivot serrations with a wire brush.

Fig 12: Cleaning Wiper Pivot Serrations With Wire Brush
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Install the wiper arm and blade with the nut. Make sure that the wiper arm and blade come to the position shown in the illustration

Standard Measurement

MEASUREMENT CONDITION

Position	Specified Condition
B	20.0 to 40.0 mm (0.787 to 1.57 in.)

Torque: 25 N*m (255 kgf*cm, 18 ft.*lbf)

HINT:

Hold down the wiper arm hinge with your hand while tightening the nut.

Operate the front wipers while spraying washer fluid on the windshield glass. Make sure that the front wipers function properly and there is no interference with the vehicle body.

Fig 13: Identifying Wiper Arm And Blade Position