LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2008 >> LS 460L >> Repair and Diagnosis >> Transmission >> Automatic Trans >> Automatic Transaxle >> Automatic Transmission System >> DTC P0748 Pressure Control Solenoid "A" Electrical (Shift Solenoid Valve SL1); DTC P0778 Pressure Control Solenoid "B" Electrical (Shift Solenoid Valve SL2); DTC P0798 Pressure Control Solenoid "C" Electrical (Shift Solenoid Valve SL3); DTC P2810 Pressure Control Solenoid "G" Electrical (Shift Solenoid Valve SL4); DTC P2819 Pressure Control Solenoid "H" Electrical (Shift Solenoid Valve SL5) >> Inspection Procedure

Inspection Procedure

HINT:

The shift solenoid valves SL1, 2, 3, 4 and 5 turn ON/OFF normally when the shift lever is on D:

Shift Solenoid Valve Operation:

SHIFT SOLENOID VALVE OPERATION CHART

Gear Position 1st 2nd 3rd 4th 5th 6th 7th 8th
Shift Solenoid Valve SL1 ON ON ON ON ON OFF OFF OFF
Shift Solenoid Valve SL2 OFF OFF OFF OFF ON ON ON ON
Shift Solenoid Valve SL3 OFF OFF ON OFF OFF OFF ON OFF
Shift Solenoid Valve SL4 OFF OFF OFF ON OFF ON OFF OFF
Shift Solenoid Valve SL5 OFF ON OFF OFF OFF OFF OFF ON
  1. CHECK HARNESS AND TRANSMISSION WIRE (TRANSMISSION WIRE - TCM, TRANSMISSION WIRE (SHIFT SOLENOID VALVE SL1, 2, 3, 4 AND 5)) 
    1. Disconnect the E6 and E7 TCM connectors.
    2. Measure the resistance of the wire harness side connectors.

      Standard Resistance 

      RESISTANCE REFERENCE

      Tester Connection Condition Specified Condition
      E6-6 (SL1+) - E6-5 (SL1-) Always 5.0 to 5.6 Ω
      E6-4 (SL2+) - E6-3 (SL2-) Always 5.0 to 5.6 Ω
      E6-2 (SL3+) - E6-1 (SL3-) Always 5.0 to 5.6 Ω
      E7-7 (SL4+) - E7-6 (SL4-) Always 5.0 to 5.6 Ω
      E7-5 (SL5+) - E7-4 (SL5-) Always 5.0 to 5.6 Ω
      E6-6 (SL1+) or E6-5 (SL1-)-Body ground Always 10 kΩ or higher
      E6-4 (SL2+) or E6-3 (SL2-) - Body ground Always 10 kΩ or higher
      E6-2 (SL3+) or E6-1 (SL3-) - Body ground Always 10 kΩ or higher
      E7-7 (SL4+) or E7-6 (SL4-) - Body ground Always 10 kΩ or higher
      E7-5 (SL5+) or E7-4 (SL5-) - Body ground Always 10 kΩ or higher
      Fig 1: Identifying E6 And E7 TCM Connector Terminals
      G04948329Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

    NG: Go to step  3

    OK: Go to next step 

  2. REPLACE TCM 
    1. Replace the TCM (see REMOVAL  ).

    NEXT: PERFORM A/T CODE REGISTRATION  (See REGISTRATION  )

  3. CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM) 
    1. Disconnect the E50 transmission wire connector.
    2. Disconnect the E6 and E7 TCM connectors.
    3. Measure the resistance of the wire harness side connectors.

      Standard Resistance 

      RESISTANCE REFERENCE

      Tester Connection Condition Specified Condition
      E50-23 (SL1+) - E6-6 (SL1+) Always Below 1 Ω
      E50-24 (SL1-) - E6-5 (SL1-) Always Below 1 Ω
      E50-28 (SL2+) - E6-4 (SL2+) Always Below 1 Ω
      E50-29 (SL2-) - E6-3 (SL2-) Always Below 1 Ω
      E50-25 (SL3+) - E6-2 (SL3+) Always Below 1 Ω
      E50-26 (SL3-) - E6-1 (SL3-) Always Below 1 Ω
      E50-15 (SL4+) - E7-7 (SL4+) Always Below 1 Ω
      E50-16 (SL4-) - E7-6 (SL4-) Always Below 1 Ω
      E50-5 (SL5+) - E7-5 (SL5+) Always Below 1 Ω
      E50-6 (SL5-) - E7-4 (SL5-) Always Below 1 Ω
      E50-23 (SL1+) or E6-6 (SL1+) - Body ground Always 10 kΩ or higher
      E50-24 (SL1-) or E6-5 (SL1-) - Body ground Always 10 kΩ or higher
      E50-28 (SL2+) or E6-4 (SL2+) - Body ground Always 10 kΩ or higher
      E50-29 (SL2-) or E6-3 (SL2-) - Body ground Always 10 kΩ or higher
      E50-25 (SL3+) or E6-2 (SL3+) - Body ground Always 10 kΩ or higher
      E50-26 (SL3-) or E6-1 (SL3-) - Body ground Always 10 kΩ or higher
      E50-15 (SL4+) or E7-7 (SL4+) - Body ground Always 10 kΩ or higher
      E50-16 (SL4-) or E7-6 (SL4-) - Body ground Always 10 kΩ or higher
      E50-5 (SL5+) or E7-5 (SL5+) - Body ground Always 10 kΩ or higher
      E50-6 (SL5-) or E7-4 (SL5-) - Body ground Always 10 kΩ or higher
      Fig 2: Identifying E6 And E7 TCM Connector Terminals
      G04948330Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

    NG: REPAIR OR REPLACE HARNESS OR CONNECTOR 

    OK: Go to next step 

  4. INSPECT SHIFT SOLENOID VALVE SL1, 2, 3, 4 AND 5 
    1. Remove the shift solenoid valves (see DISASSEMBLY  ).
    2. Measure the resistance of the shift solenoid valves.

      Standard Resistance 

      RESISTANCE REFERENCE

      Tester Connection Condition Specified Condition
      Terminal 1 of the shift solenoid valve SL1 - terminal 2 20°C (68°F) 5.0 to 5.6 Ω
      Terminal 1 of the shift solenoid valve SL2 - terminal 2 20°C (68°F) 5.0 to 5.6 Ω
      Terminal 1 of the shift solenoid valve SL3 - terminal 2 20°C (68°F) 5.0 to 5.6 Ω
      Terminal 1 of the shift solenoid valve SL4 - terminal 2 20°C (68°F) 5.0 to 5.6 Ω
      Terminal 1 of the shift solenoid valve SL5 - terminal 2 20°C (68°F) 5.0 to 5.6 Ω
    3. Connect the battery's positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector. Then check that the valve moves and makes an operating noise.
      Fig 3: Identifying Shift Solenoid Valves Connector Terminals
      G04948331Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      OK: Valve moves and makes operating noise. 

    NG: REPLACE SHIFT SOLENOID VALVE  (See DISASSEMBLY  )

    OK: REPAIR OR REPLACE TRANSMISSION WIRE  (See REMOVAL  )

scientia non olet · About LEMON Manuals