Data List / Active Test

HINT:

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

1. Connect the Techstream to the DLC3.
2. Turn the engine switch on (IG).
3. Turn the Techstream on.
4. Enter the following menus: Body Electrical / Sliding Roof / Data List.
5. Read the Data List according to the display on the Techstream
   Fig 1: Identifying Sliding Roof Switch Assembly With Switch Condition

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   Sliding Roof 

   SLIDING ROOF SPECIFICATION
   
   

   Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
   Hall IC1 Pulse	Sliding roof operation signal/LO or HI	LO Sliding roof motor is not operating HI Sliding roof motor is operating	-
   Hall IC1 Status	Sliding roof operation signal/ NORMAL or LOCK	NORMAL Sliding roof motor is operating LOCK Sliding roof motor is not operating	-
   Hall IC2 Pulse	Sliding roof operation signal/LO or HI	LO Sliding roof motor is not operating HI Sliding roof motor is operating	-
   Hall IC2 Status	Sliding roof operation signal/ NORMAL or LOCK	NORMAL Sliding roof motor is operating LOCK Sliding roof motor is not operating	-
   Ignition (Direct Signal)	Ignition switch signal/ON or OFF	ON Engine switch on (IG) OFF Engine switch off	-
   Ignition (MPX)	Ignition switch signal (MPX signal)/ON or OFF	ON Engine switch on (IG) OFF Engine switch off	-
   Door Courtesy	Driver's door courtesy light switch signal/ON or OFF	ON Driver's door is open OFF Driver's door is closed	-
   Door Key Open Operation	Key-linked sliding roof open signal/ON or OFF	ON Door lock is turned to open position using key OFF Door lock is not turned	-
   Door Key Close Operation	Key-linked sliding roof close signal/ON or OFF	ON Door lock is turned to close position using key OFF Door lock is not turned	-
   Wireless Open Operation	Wireless sliding roof open signal/ ON or OFF	ON Transmitter UNLOCK switch is pressed OFF Transmitter UNLOCK switch is not pressed	-
   Wireless Close Operation	Wireless sliding roof close signal/ ON or OFF	ON Transmitter LOCK switch is pressed OFF Transmitter LOCK switch is not pressed	-
   Door Key Related (Open)	Key-linked sliding roof open permit signal/Available or Not available	Available Turn and hold the driver side door key to UNLOCK position for 3 seconds or more Not Available Any status except "Available" status	-
   Door Key Related (Close)	Key-linked sliding roof close permit signal/Available or Not available	Available Turn and hold the driver side door key to LOCK position for 3 seconds or more Not Available Any status except "Available" status	-
   Wireless Key Rel (Open)	Wireless sliding roof open permit signal/Available or Not available	Available Press and hold the transmitter UNLOCK switch for 4 seconds or more with key is not in the vehicle Not Available Any status except "Available" status	-
   Door Key Related Operation	Key-linked sliding roof operation signal/Tilt or Slide	Tilt Sliding roof Tilt operates Slide Sliding roof Slide operates	-
   Wireless Key Rel Operation	Wireless sliding roof operation signal/Tilt or Slide	Tilt Sliding roof Tilt operates Slide Sliding roof Slide operates	-
   Key Off Permission	Key-off sliding roof operation permit signal/ON or OFF	ON Front doors are not opened within 45 seconds after engine switch is turned off OFF Any status except "ON" status	-
   Rotary SW	Sliding roof switch assembly switch position signal/Over, Open, Pos1, Pos2, Pos3, Pos4, Pos5, Pos6, Close or Tilt Up	Over Switch position [1] in the illustration Open Switch position [2] in the illustration Pos1 Switch position [3] in the illustration Pos2 Switch position [4] in the illustration Pos3 Switch position [5] in the illustration Pos4 Switch position [6] in the illustration Pos5 Switch position [7] in the illustration Pos6 Switch position [8] in the illustration Close Switch position [9] in the illustration Tilt Up Switch position [10] in the illustration	-

HINT.

Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

1. Connect the Techstream to the DLC3
2. Turn the engine switch on (IG)
3. Turn the Techstream on.
4. Enter the following menus Body Electrical / Sliding Roof / Active Test
5. Perform the Active Test according to the display on the Techstream.

   Sliding Roof 

   SLIDING ROOF SPECIFICATION
   
   

   Tester Display	Test Part	Control Range	Diagnostic Note
   Slide Roof	Operate sliding roof	CLOS/UP / OFF	-
   Slide Roof	Operate sliding roof	OPN/DWN / OFF	-