LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2008 >> IS 250 RWD, Automatic >> Repair and Diagnosis >> External Pages >> Different car >> Section 47 (Mirror (Exterior)) >> Outer Rear View Mirror >> Inspection

Outer Rear View Mirror: Inspection

WARNING: This page is about a different car, the 2008 Lexus IS F. However, it is still accessible from the selected car via links, so may be relevant.
  1. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH 
    1. Inspect outer mirror motor operation
      1. Apply battery voltage and check the operation of the mirror face, as shown in the table and illustration

        Standard 

        VOLTAGE SPECIFICATION

        Measurement Condition Specified Condition
        Battery positive (+) → Terminal 1 (MV)
        Battery negative (-) → Terminal 10 (M+)        		 Turns upward (A)
        Battery positive (+) → Terminal 10 (M+)
        Battery negative (-) → Terminal 1 (MV)        		 Turns downward (B)
        Battery positive (+) → Terminal 9 (MH)
        Battery negative (-) → Terminal 10 (M+)        		 Turns left (C)
        Battery positive (+) → Terminal 10 (M+)
        Battery negative (-) → Terminal 9 (MH)        		 Turns right (D)
        Fig 1: Inspecting Outer Rear View Mirror Assembly RH
        G05756202Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

        If the result is not as specified, replace the mirror assembly.

    2. Inspect outer mirror heater operation
      1. Apply battery voltage and check the operation of the mirror face, as shown in the table below

        Standard 

        VOLTAGE SPECIFICATION

        Measurement Condition Specified Condition
        Battery positive (+) → Terminal 3 (+)
        Battery negative (-) → Terminal 9 (-)        		 Mirror surface temperature becomes higher

        If the result is not as specified, replace the mirror assembly

    3. Inspect electrochromatic outer mirror operation.
      1. Apply battery voltage and check the operation of the mirror face, as shown in the table and illustration

        Standard 

        VOLTAGE SPECIFICATION

        Measurement Condition Specified Condition
        Battery positive (+) → Terminal 7 (EC+)
        Battery negative (-) → Terminal 15 (EC)        		 Mirror surface changes to dark

        If the result is not as specified, replace the mirror assembly

        Fig 2: Identifying g1 Connector Terminal
        G05756203Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  2. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH 
    1. Inspect outer mirror motor operation.
      1. Remove the outer rear view mirror assembly
      2. Apply battery voltage and check the operation of the mirror face, as shown in the table and illustration.

        Standard 

        VOLTAGE SPECIFICATION

        Measurement Condition Specified Condition
        Battery positive (+) → Terminal 1 (MV)
        Battery negative (-) → Terminal 10 (M+)        		 Turns upward (A)
        Battery positive (+) → Terminal 10 (M+)
        Battery negative (-) → Terminal 1 (MV)        		 Turns downward (B)
        Battery positive (+) → Terminal 9 (MH)
        Battery negative (-) → Terminal 10 (M+)        		 Turns left (C)
        Battery positive (+) → Terminal 10 (M+)
        Battery negative (-) → Terminal 9 (MH)        		 Turns right (D)
        Fig 3: Identifying h1 Connector Terminal
        G05756204Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

        If the result is not as specified, replace the mirror assembly.

    2. Inspect outer mirror heater operation
      1. Apply battery voltage and check the operation of the mirror face, as shown in the table below

        Standard 

        VOLTAGE SPECIFICATION

        Measurement Condition Specified Condition
        Battery positive (+) → Terminal 3 (HTR+)
        Battery negative (-) → Terminal 9 (HTR-)        		 Mirror surface temperature becomes higher

        If the result is not as specified, replace the mirror assembly

    3. Inspect electrochromatic outer mirror operation
      1. Apply battery voltage and check the operation of the mirror face, as shown in the table and illustration

        Standard 

        VOLTAGE SPECIFICATION

        Measurement Condition Specified Condition
        Battery positive (+) → Terminal 7 (EC+)
        Battery negative (-) → Terminal 15 (EC-)        		 Mirror surface changes to dark

        If the result is not as specified, replace the mirror assembly.

        Fig 4: Identifying h1 Connector Terminal
        G05756205Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
scientia non olet · About LEMON Manuals