Typical Enabling Conditions
WARNING: This page is about a different car, the 2008 Lexus IS F. However, it is still accessible from the selected car via links, so may be relevant.
TYPICAL ENABLING CONDITIONS
| The monitor will run whenever the following DTCs are not present | None |
| Turbine speed sensor circuit | Not circuit malfunction |
| Output speed sensor circuit | Not circuit malfunction |
| Input speed sensor circuit | Not circuit malfunction |
| ATF temperature sensor circuit | Not circuit malfunction |
| Shift solenoid valve SL1 circuit | Not circuit malfunction |
| Shift solenoid valve SL2 circuit | Not circuit malfunction |
| Shift solenoid valve SL3 circuit | Not circuit malfunction |
| Shift solenoid valve SL4 circuit | Not circuit malfunction |
| Shift solenoid valve SL5 circuit | Not circuit malfunction |
| Shift solenoid valve SR circuit | Not circuit malfunction |
| Shift solenoid valve SLT circuit | Not circuit malfunction |
| ECT (Engine coolant temperature) sensor circuit | Not circuit malfunction |
| KCS sensor circuit | Not circuit malfunction |
| ETCS (Electronic throttle control system) | Not system down |
| CAN communication circuit (ECM - TCM) | Not system down |
| NSW switch | "D" |
| Duration time from shifting "N" to "D" | 4 sec or more |
| ATF temperature | -10°C (14°F) or more |
| Engine | Starting |
ON malfunction (A)
TYPICAL ENABLING CONDITIONS
| Turbine speed | 270 rpm or more |
| TCM selected gear | 1st |
| Turbine speed - Output speed (NT - NO) x 1st gear ratio | 150 rpm or more |
ON malfunction (B)
TYPICAL ENABLING CONDITIONS
| Turbine speed | 270 rpm or more |
| TCM selected gear | 2nd |
| TCM indicated pressure value of SL5 | 1600 kPa (16 3 kgf/cm2 , 232 psi) |
| Turbine speed - Output speed (NT - NO) x 2nd gear ratio | 150 rpm or more |
| Output speed | more than 0 rpm |
ON malfunction (C)
TYPICAL ENABLING CONDITIONS
| Turbine speed | 270 rpm or more |
| TCM selected gear | 3rd |
| TCM indicated pressure value of SL3 | 1600 kPa (16 3 kgf/cm2 , 232 psi) |
| Turbine speed - Output speed (NT - NO) x 3rd gear ratio | 150 rpm or more |
| Output speed | more than 0 rpm |
ON malfunction (D)
TYPICAL ENABLING CONDITIONS
| Turbine speed | 270 rpm or more |
| TCM selected gear | 4th |
| TCM indicated pressure value of SL4 | 1600 kPa (16 3 kgf/cm2 , 232 psi) |
| Turbine speed - Output speed (NT - NO) x 4th gear ratio | 150 rpm or more |
| Output speed | more than 0 rpm |
ON malfunction (E)
TYPICAL ENABLING CONDITIONS
| TCM selected gear | 5th, 6th, 7th or 8th |
| TCM indicated pressure value of SL2 | 1600 kPa (16 3 kgf/cm2 , 232 psi) |
| Time after transmission shifts to TCM selected gear (when detected abnormal shift) | 1 5 sec or more |
| Input speed | 0 rpm or less or 50 rpm or more |
ON malfunction (F)
TYPICAL ENABLING CONDITIONS
| Output speed sensor circuit | Not circuit malfunction |
| TCM indicated pressure value of SL1 | 1600 kPa (16 3 kgf/cm2 , 232 psi) |
| Input speed when output speed sensor fail-safe function does not operate | 12799 rpm or less |
| Transmission range | "D" |
| When one of following conditions is met | Condition (1), (2) or (3) |
|
ON |
|
OFF malfunction |
|
ON malfunction |