LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2008 >> IS 250 RWD, Automatic >> Repair and Diagnosis >> External Pages >> Different car >> Section 1 (Exterior) >> Rear Bumper >> Removal

Rear Bumper: Removal

WARNING: This page is about a different car, the 2008 Lexus IS F. However, it is still accessible from the selected car via links, so may be relevant.
  1. REMOVE NO. 2 LUGGAGE COMPARTMENT TRIM COVER (w/ Intuitive Parking Assist System) 
  2. REMOVE DECK SIDE TRIM BOX LH (w/ Intuitive Parking Assist System) 
  3. REMOVE DECK SIDE TRIM BOX RH (w/ Intuitive Parking Assist System) 
  4. REMOVE ROPE HOOK ASSEMBLY (w/ Intuitive Parking Assist System)  (See REMOVAL )
  5. REMOVE REAR LUGGAGE COMPARTMENT TRIM COVER (w/ Intuitive Parking Assist System)  (See REMOVAL )
  6. REMOVE NO. 2 ROOM LIGHT ASSEMBLY (w/ Intuitive Parking Assist System)  (See REMOVAL )
  7. REMOVE ROPE HOOK (w/ Intuitive Parking Assist System)  (See REMOVAL )
  8. REMOVE NO. 2 LUGGAGE COMPARTMENT TRIM HOOK (w/ Intuitive Parking Assist System)  (See REMOVAL )
  9. REMOVE FRONT LUGGAGE COMPARTMENT TRIM COVER (w/ Intuitive Parking Assist System)  (See REMOVAL )
  10. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK (w/ Intuitive Parking Assist System)  (See REMOVAL )
  11. REMOVE SIDE LUGGAGE COMPARTMENT TRIM COVER LH (w/ Intuitive Parking Assist System)  (See REMOVAL )
  12. REMOVE NO. 1 REAR BUMPER PLATE 
    1. Using a screwdriver, disengage the 2 claws and remove the No. 1 rear bumper plate

      HINT.

      • Tape the screwdriver tip before use
      • Use the same procedure for the RH side and LH side.
        Fig 1: Identifying No. 1 Rear Bumper Plate Claws
        G05756719Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  13. REMOVE REAR BUMPER ASSEMBLY 
    1. w/ Intuitive Parking Assist System.
      1. Disconnect the No. 3 luggage room wire connector
        Fig 2: Locating No. 3 Luggage Room Wire Connector
        G05756720Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Put protective tape around the rear bumper assembly
    3. Using a clip remover, remove the 2 clips
    4. Remove the 6 screws and 2 rear bumper seal brackets.
      Fig 3: Identifying Rear Bumper Seal Brackets Screws
      G05756721Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Disengage the 6 claws and disconnect the rear bumper assembly as shown in the illustration

      HINT.

      Use the same procedure for the RH side and LH side.

      Fig 4: Identifying Rear Bumper Assembly Claws
      G05756722Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    6. Disengage the 4 claws and remove the rear bumper assembly as shown in the illustration.
      Fig 5: Identifying Rear Bumper Assembly Claws
      G05756723Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    7. w/ Intuitive Parking Assist System:
      1. Disengage the clamp and remove the grommet
        Fig 6: Identifying Grommet And Clamp
        G05756724Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
scientia non olet · About LEMON Manuals