Rear Bumper: Removal

DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
REMOVE NO. 2 LUGGAGE COMPARTMENT TRIM COVER (w/ Clearance Sonar System)
REMOVE DECK SIDE TRIM BOX LH (w/ Clearance Sonar System)
REMOVE DECK SIDE TRIM BOX RH (w/ Clearance Sonar System)
REMOVE ROPE HOOK ASSEMBLY (w/ Clearance Sonar System)
1. Remove the 3 bolts and 3 rope hook assemblies.
REMOVE REAR LUGGAGE COMPARTMENT TRIM COVER (w/ Clearance Sonar System)
1. Remove the triangle reflector.
2. Using a clip remover, remove the 3 clips.
3. Disengage the 4 clips and remove the rear luggage compartment trim cover.
  
  Fig 2: Identifying Rear Luggage Compartment Trim Cover Clips
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
REMOVE NO. 2 ROOM LIGHT ASSEMBLY (w/ Clearance Sonar System)
1. Disengage the claw and disconnect the No. 2 room light assembly.
2. Disconnect the connector and remove the No. 2 room light assembly.
  
  Fig 3: Identifying No. 2 Room Light Assembly Claw
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
REMOVE ROPE HOOK (w/ Clearance Sonar System)
1. Remove the 2 rope hooks.
  
  Fig 4: Identifying Rope Hooks
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
REMOVE FRONT LUGGAGE COMPARTMENT TRIM COVER (w/ Clearance Sonar System)
1. Remove the 3 luggage compartment trim hooks as shown in the illustration.
  
  Fig 5: Removing Luggage Compartment Trim Hooks
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Using a clip remover, remove the 2 clips.
3. Disengage the 4 claws and remove the front luggage compartment trim cover.
  
  Fig 6: Identifying Front Luggage Compartment Trim Cover Claws And Clip
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK (w/ Clearance Sonar System)
1. Remove the screw and No. 1 luggage compartment trim hook.
  
  Fig 7: Identifying No. 1 Luggage Compartment Trim Hook Screw
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
REMOVE SIDE LUGGAGE COMPARTMENT TRIM COVER LH (w/ Clearance Sonar System)
1. Using a clip remover, remove the 3 clips and side luggage compartment trim cover LH.
  
  Fig 8: Identifying Side Luggage Compartment Trim Cover LH Clips
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
DISCONNECT NO. 3 LUGGAGE ROOM WIRE (w/ Clearance Sonar System)
1. Disconnect the No. 3 luggage room wire connector.
2. Disengage the grommet.
  
  Fig 9: Locating No. 3 Luggage Room Wire Connector
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
REMOVE NO. 1 REAR BUMPER PLATE
1. Using a screwdriver, disengage the 2 claws and remove the No.1 rear bumper plate.
  HINT:
  - Tape the screwdriver tip before use.
  - Use the same procedures for the RH side and LH side.
    
    Fig 10: Disengaging Claws
    Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
REMOVE REAR BUMPER ASSEMBLY
1. Put protective tape around the rear bumper assembly.
2. Using a clip remover, remove the 2 clips.
3. Remove the 6 screws and 2 rear bumper seal brackets.
  
  Fig 11: Identifying Rear Bumper Assembly Screws And Clips
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
4. Disengage the 6 claws and disconnect the rear bumper assembly as shown in the illustration.
  HINT:
  
  Use the same procedures for the RH side and LH side.
  
  Fig 12: Disconnecting Rear Bumper Assembly
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
5. Disengage the 4 claws and remove the rear bumper assembly as shown in the illustration.
Fig 13: Removing Rear Bumper Assembly
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002