LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2007 >> RX 400h FWD >> Repair and Diagnosis >> Accessories & Equipment >> Gauges & Instrument Panels >> Instrument Panel >> Instrument Panel Safety Pad >> Disassembly

Instrument Panel Safety Pad: Disassembly

  1. REMOVE SPEAKER HOLE NO.1 COVER (w/Mark Levinson Speaker System) 
    1. Disengage the 4 clips and remove the speaker hole No.1 cover.
    Fig 1: Identifying Speaker Hole No.1 Cover Clips
    G05274394Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  2. REMOVE INSTRUMENT PANEL NO.1 SPEAKER PANEL SUB-ASSEMBLY 
    1. Disengage the 2 clips and remove the instrument panel No.1 speaker panel sub-assembly.
      2. Fig 2: Identifying Instrument Panel No.1 Speaker Panel Sub-Assembly Clips
      G05274395Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  3. REMOVE INSTRUMENT PANEL NO.2 SPEAKER PANEL SUB-ASSEMBLY 

    HINT:

    Use the same procedures for the instrument panel No.2 speaker panel sub-assembly and the instrument panel No.1 speaker panel sub-assembly.

  4. REMOVE FRONT NO.2 SPEAKER (w/Mark Levinson Speaker System)  (See REMOVAL )
  5. REMOVE FRONT NO.2 SPEAKER  (See REMOVAL )
  6. REMOVE FRONT NO.2 SPEAKER  (See REMOVAL )
  7. REMOVE LIGHT CONTROL RHEOSTAT 
    1. Disengage the 2 claws and remove the light control rheostat.
    Fig 3: Identifying Light Control Rheostat Claws
    G05281219Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  8. REMOVE SIDE DEFROSTER NO.3 NOZZLE DUCT 
    1. Remove the screw < C> and the side defroster No.3 nozzle duct.
      2. Fig 4: Identifying Side Defroster No.3 Nozzle Duct Screw
      G05274396Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  9. REMOVE SIDE DEFROSTER NO.4 NOZZLE DUCT 

    HINT:

    Use the same procedures for the side defroster No. 4 nozzle duct and the side defroster No.3 nozzle duct.

  10. REMOVE INSTRUMENT PANEL NO.1 PIN 
    1. Remove the screw < C> and the instrument panel No.1 pin.
    Fig 5: Locating Instrument Panel No.1 Pin Screw
    G05274397Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  11. REMOVE DEFROSTER NOZZLE ASSEMBLY 
    1. Remove the 3 screws < C> and the defroster nozzle assembly.
    Fig 6: Identifying Defroster Nozzle Assembly Screws
    G05274398Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  12. REMOVE HEATER TO REGISTER NO.1 DUCT 
    1. Remove the 4 screws < C> and the heater to register No. 1 duct.
      2. Fig 7: Identifying Heater And Register No.1 Duct Screws
      G05274399Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  13. REMOVE HEATER TO REGISTER NO.4 DUCT 

    HINT:

    Use the same procedures for the heater to register No. 4 duct and the heater to register No.1 duct.

  14. REMOVE HEATER TO REGISTER CENTER SUB DUCT 
    1. Remove the 2 screws < C> and the heater to register center sub duct.
    Fig 8: Identifying Heater And Register Center Sub Duct Screws
    G05274400Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  15. REMOVE SIDE DEFROSTER NO.1 NOZZLE DUCT 
    1. Remove the screw < C> and the side defroster No.1 nozzle duct.
      2. Fig 9: Identifying Side Defroster No.1 Nozzle Duct Screw
      G05274401Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  16. REMOVE SIDE DEFROSTER NO.2 NOZZLE DUCT 

    HINT:

    Use the same procedures for the side defroster No.2 nozzle duct and the side defroster No.1 nozzle duct.

  17. REMOVE SIDE DEFROSTER NO.1 NOZZLE 
    1. Disengage the 2 claws and remove the side defroster No. 1 nozzle.
      2. Fig 10: Identifying Side Defroster No.1 Nozzle Claws
      G05274402Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  18. REMOVE SIDE DEFROSTER NO.2 NOZZLE 

    HINT:

    Use the same procedures for the side defroster No.2 nozzle and the side defroster No.1 nozzle.

  19. REMOVE WINDSHIELD WIPER RELAY ASSEMBLY (w/ Rain Sensor) 
    1. Remove the screw < C> and the windshield wiper relay assembly.
    Fig 11: Identifying Windshield Wiper Relay Assembly (W/ Rain Sensor) Screw
    G05281227Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  20. REMOVE NETWORK GATEWAY ECU 
    1. Remove the screw < C> and the network gateway ECU.
    Fig 12: Identifying Network Gateway ECU Screw
    G05281228Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  21. REMOVE DEFROSTER NOZZLE NO.1 GARNISH 
    1. Disengage the 2 clips and 4 claws then remove the defroster nozzle No.1 garnish.
    Fig 13: Identifying Defroster Nozzle No.1 Garnish Clips And Claws
    G05274403Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  22. REMOVE INSTRUMENT PANEL BRACKET SUB-ASSEMBLY CENTER 
    1. Remove the screw < C> and the instrument panel bracket sub-assembly center.
    Fig 14: Identifying Instrument Panel Bracket Sub-Assembly Center Screw
    G05274404Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  23. REMOVE GLOVE BOX LIGHT ASSEMBLY 
    1. Disconnect the connector.
      2. Fig 15: Identifying Glove Box Light Assembly Clamp
      G05274405Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disengage the 2 claws and remove the glove box light assembly.
  24. REMOVE NO.2 RADIO ANTENNA CORD (w/o Navigation System)  (See REMOVAL )
  25. REMOVE NO.2 RADIO ANTENNA CORD (w/ Navigation System)  (See REMOVAL )
  26. REMOVE INSTRUMENT PANEL NO.2 WIRE 
    1. Remove the 2 screws.
    2. Disengage the 18 clamps and remove the instrument panel No.2 wire.
    Fig 16: Identifying Instrument Panel No.2 Wire Clamps
    G05274406Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  27. REMOVE AUTOMATIC LIGHT CONTROL SENSOR 
    1. Remove the automatic light control sensor.
    NOTE: Do not pry the automatic light control sensor off from the upper position.
    Fig 17: Identifying Automatic Light Control Sensor Clip
    G05205205Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  28. REMOVE FRONT PASSENGER AIRBAG ASSEMBLY  (See REMOVAL )
scientia non olet · About LEMON Manuals