Inspection Procedure

HINT:

• If DTC P0011 or P0012 is displayed, check the right bank VVT system (bank 1).
• Bank 1 refers to the bank that includes cylinder No. 1.
• If DTC P0021 or P0022 is displayed, check the left bank VVT system (bank 2).
• Bank 2 refers to the bank that does not include cylinder No. 1.
• Read freeze frame data using an intelligent tester. The ECM (Included in HV control ECU) records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.

1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0011, P0012, P0021 OR P0022) 
   1. Connect the intelligent tester to the DLC3.
   2. Turn the ignition switch to the ON position and turn the tester ON.
   3. Enter the following menus: DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODES.
   4. Read the DTCs.

   Result 

   RESULT REFERENCE
   
   

   Display (DTC Output)	Proceed to
   P0011, P0012, P0021 or P0022	A
   POOH, P0012, P0021 or P0022 and other DTCs	B

   HINT:

   If any DTCs other than P0011, P0012, P0021 or P0022 are output, troubleshoot those DTCs first.

   B: GO TO  DTC CHART  

   A: Go to next step 

2. PERFORM ACTIVE TEST BY CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (OPERATE OCV) 
   1. Connect the intelligent tester to the DLC3.
   2. Turn the ignition switch to the ON position and turn the tester ON.
   3. Put the engine in inspection mode (See INSPECTION MODE PROCEDURE ).
   4. Warm up the engine.
   5. On the tester, enter the following menus: DIAGNOSIS / ENHANCED OBD II / ACTIVE TEST / VVT CTRL B1 or VVT CTRL B2.
   6. Check the engine speed while operating the Oil Control Valve (OCV) using the tester.

   OK 

   TESTER OPERATION AND SPECIFIED CONDITION
   
   

   Tester Operation	Specified Condition
   OCV OFF	Normal engine speed
   OCV ON	Engine idles roughly or stalls (soon after OCV switched from OFF to ON)

   NG: GO TO step   4 

   OK: Go to next step 

3. CHECK WHETHER DTC OUTPUT RECURS (DTC P0011, P0012, P0021 OR P0022) 
   1. Connect the intelligent tester to the DLC3.
   2. Turn the ignition switch to the ON position and turn the tester ON.
   3. Clear the DTCs.
   4. Start the engine and warm it up.
   5. Switch the ECM (Included in HV control ECU) from normal mode to check mode using the tester.
   6. Drive the vehicle for more than 10 minutes.
   7. Read the DTCs using the tester.

   OK: No DTC output. 

   NG: GO TO step 4 

   OK: END 

4. CHECK VALVE TIMING (CHECK FOR LOOSE AND JUMPED TEETH ON TIMING BELT) 
   1. Remove the cylinder head covers RH and LH.
   2. Turn the crankshaft pulley, and align its groove with timing mark "0" of the timing belt cover.
   3. Check that the timing marks of the camshaft timing gears are aligned with the timing marks of the No. 3 timing belt cover as shown in the illustration.

      If not, turn the crankshaft 1 revolution (360°), then align the marks as above.

      OK: The timing marks on the camshaft timing gears are aligned as shown in the illustration. 

   4. Reinstall the cylinder head cover.

   NG: ADJUST VALVE TIMING 

   Fig 1: Identifying Matchmarks Of Camshaft Pulley And Camshaft Bearing Cap

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   OK: Go to next step 

5. INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (OCV) 
   1. Remove the OCV.
   2. Measure the resistance between the terminals of the OCV.

      Standard resistance: 

      6.9 to 7.9 Ω at 20°C (68°F) 

   3. Apply positive battery voltage to terminal 1 and the negative battery voltage to terminal 2. Check the valve operation.

      OK: Valve moves quickly. 

   4. Reinstall the OCV.

   NG: REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY 

   Fig 2: Measuring Resistance Between Terminals Of OCV

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   OK: Go to next step 

6. INSPECT OIL CONTROL VALVE FILTER 
   1. Remove the oil control valve filter.

   OK: The filter is not clogged. 

   NG: CLEAN OIL CONTROL VALVE FILTER 

   OK: Go to next step 

7. REPLACE CAMSHAFT TIMING GEAR ASSEMBLY 
8. READ VALUE OF INTELLIGENT TESTER (CHECK IF DTC OUTPUT RECURS) 
   1. Connect the intelligent tester to the DLC3.
   2. Turn the ignition switch to the ON position and turn the tester ON.
   3. Clear the DTCs.
   4. Start the engine and warm up.
   5. Switch the ECM (Included in HV control ECU) from normal mode to the check mode using the tester.
   6. Drive the vehicle for more than 10 minutes.
   7. Read the output DTCs using the intelligent tester.

      Standard: No DTC output. 

      HINT:

      DTC P0011, P0012, P0021 or P0022 is output when foreign objects in engine oil are caught in some parts of the system. These codes will stay registered even if the system returns to normal after a short time. These foreign objects are then captured by the oil filter, thus eliminating the source of the problem.

   OK: SYSTEM OK 

   NG: REPLACE HV CONTROL ECU