LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2007 >> RX 400h AWD >> Repair and Diagnosis >> Body & Frame >> Sun Roof/T-Top/Convertible Top >> Interior >> Roof Headlining >> Removal

Roof Headlining: Removal

  1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 
  2. REMOVE TONNEAU COVER ASSEMBLY 
  3. REMOVE DECK BOARD SUB-ASSEMBLY 
    1. Disengage the 5 clips and turn up the front side of the deck board.
    2. Remove the 2 bolts and deck board sub-assembly.
    Fig 1: Identifying Bolts And Deck Board Sub-Assembly
    G05281727Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  4. REMOVE DECK FLOOR BOX FRONT 
    1. Using a clip remover, remove the 2 clips and deck floor box front.
    Fig 2: Identifying Deck Floor Box Front With Clips
    G05281728Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  5. REMOVE DECK FLOOR BOX REAR 
    1. Using a clip remover, remove the 2 clips and deck floor box rear.
    Fig 3: Identifying Deck Floor Box Rear With Clips
    G05281729Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  6. REMOVE DECK NO.3 BOARD SUB-ASSEMBLY 
    1. Remove the 2 bolts, 2 nuts and deck No.3 board sub-assembly.
    Fig 4: Identifying Bolts, Nuts And Deck No.3 Board Sub-Assembly
    G05281730Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  7. REMOVE DECK NO.2 BOARD SUB-ASSEMBLY 
    1. Remove the 4 blots, 2 nuts and deck No.2 board sub-assembly.
      2. Fig 5: Identifying Blots, Nuts And Deck No.2 Board Sub-Assembly
      G05281731Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  8. REMOVE BACK DOOR WEATHERSTRIP 
  9. REMOVE REAR FLOOR FINISH PLATE 
    1. Using a clip remover, remove the 2 clips.
    2. Disengage the 2 claws and 6 clips, and remove the rear floor finish plate.
      3. Fig 6: Identifying Claws, Clips And Rear Floor Finish Plate
      G05281732Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  10. REMOVE JACK CARRIER ASSEMBLY 
    1. Remove the jack carrier support, jack assembly and jack carrier assembly.
  11. REMOVE DECK SIDE TRIM LH BOX 
    1. Remove the clip (A).
    2. Using a clip remover, remove the clip (B) and deck side trim box.
      3. Fig 7: Identifying Clip And Deck Side Trim Box
      G05281733Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  12. REMOVE DECK SIDE TRIM RH BOX 
  13. REMOVE REAR SEAT TRACK BRACKET COVER  (See REMOVAL )
  14. REMOVE REAR SEAT ASSEMBLY LH  (See REMOVAL )
  15. REMOVE REAR SEAT TRACK BRACKET COVER  (See REMOVAL )
  16. REMOVE REAR SEAT ASSEMBLY RH  (See REMOVAL )
  17. REMOVE FRONT DOOR SCUFF LH PLATE 
    1. Disengage the 6 claws and 4 clips, and remove the front door scuff plate.
    2. Disconnect the connector. (w/illumination scuff plate)
      3. Fig 8: Identifying Claws And Clips And Front Door Scuff Plate
      G05281734Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  18. REMOVE FRONT DOOR SCUFF RH PLATE 
  19. REMOVE FRONT DOOR OPENING TRIM LH WEATHERSTRIP 
  20. REMOVE FRONT DOOR OPENING TRIM RH WEATHERSTRIP 
  21. REMOVE REAR DOOR SCUFF LH PLATE 
    1. Disengage the 4 claws and 2 clips, and remove the rear door scuff plate.
    2. Disconnect the connector. (w/illumination scuff plate)
      3. Fig 9: Identifying Claws And Clips And Rear Door Scuff Plate
      G05281735Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  22. REMOVE REAR DOOR SCUFF RH PLATE 
  23. REMOVE REAR DOOR OPENING TRIM LH WEATHERSTRIP 
  24. REMOVE REAR DOOR OPENING TRIM RH WEATHERSTRIP 
  25. REMOVE FRONT PILLAR LH GARNISH 
    1. Detach clip (A) from the vehicle body. Pull the pillar garnish so that the tip of clip (B) locks in the pillar garnish hole.
    2. Using needle-nose pliers, rotate clip (B) 90°.
    3. Disengage the 2 claws and remove the front pillar garnish.
    4. Remove clip (B).
      Fig 10: Identifying Claws And Front Pillar Garnish
      G05281736Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Protect the curtain shield airbag assembly.
      1. Thoroughly cover the airbag with a cloth or nylon sheet that is 700 mm (27.56 in.) x 120 mm (4.72 in.) and fix the ends of the cover with adhesive tape, as shown in the illustration.
        NOTE: Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.
  26. REMOVE FRONT PILLAR RH GARNISH 
    Fig 11: Identifying Adhesive Tape Dimension
    G05281737Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  27. REMOVE LAP BELT OUTER ANCHOR COVER 
    1. Disengage the 2 claws and remove the lap belt outer anchor, as shown in the illustration.

      HINT:

      Use the same procedure to remove the other side.

    Fig 12: Removing Lap Belt Outer Anchor Cover
    G05281738Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  28. SEPARATE FRONT SEAT OUTER LH BELT ASSEMBLY 
    1. Remove the bolt and separate the front seat outer LH belt assembly.
      2. Fig 13: Identifying Bolt And Front Seat Outer LH Belt Assembly
      G05281739Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  29. SEPARATE FRONT SEAT OUTER RH BELT ASSEMBLY 
  30. REMOVE CENTER PILLAR LH GARNISH LOWER 
    1. Disengage the 3 claws and 2 clips, and remove the center pillar garnish lower.
      2. Fig 14: Identifying Claws, Clips And Center Pillar Garnish Lower
      G05281740Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  31. REMOVE CENTER PILLAR RH GARNISH LOWER 
  32. REMOVE CENTER PILLAR LH GARNISH 
    1. Remove the 2 screws.
    2. Disengage the clip and remove the center pillar garnish by pulling it down.
      3. Fig 15: Identifying Clip And Center Pillar Garnish
      G05281741Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  33. REMOVE CENTER PILLAR RH GARNISH 
  34. REMOVE DECK SIDE TRIM LH COVER 
    1. Using a molding remover, disengage 3 claws (A).
    2. Disengage 2 claws (B) and remove the deck side trim cover by pulling it to inside the vehicle.
      3. Fig 16: Identifying Claws And Deck Side Trim Cover
      G05281742Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  35. REMOVE DECK SIDE TRIM RH COVER 
  36. SEPARATE REAR NO.1 SEAT OUTER LH BELT ASSEMBLY 
    1. Remove the bolt and separate the rear No.1 seat outer belt assembly.
  37. SEPARATE REAR NO.1 SEAT OUTER RH BELT ASSEMBLY 
  38. REMOVE REAR SEAT SIDE LH COVER 
    1. Using a clip remover, remove the 3 clips.
    2. Disengage the 4 clips and remove the rear seat side cover.
      3. Fig 17: Removing Rear Seat Side Cover
      G05281743Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  39. REMOVE REAR SEAT SIDE RH COVER 
  40. REMOVE REAR FLOOR FINISH SIDE LH PLATE 
    1. Using a clip remover, remove the clip.
    2. Disengage the 2 clips and remove the rear floor finish side plate.
      3. Fig 18: Removing Rear Floor Finish Side Plate
      G05281744Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  41. REMOVE REAR FLOOR FINISH SIDE RH PLATE 
  42. REMOVE ROPE HOOK 
    1. Remove the 2 bolts and 2 rope hooks.

      HINT:

      Use the same procedure to remove the other side.

  43. REMOVE DECK TRIM SIDE LH PANEL ASSEMBLY 
    1. Using a clip remover, remove the 4 clips.
    2. Disengage the 2 clips and remove the deck trim side panel assembly.
      3. Fig 19: Removing Deck Trim Side Panel Assembly
      G05281745Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  44. REMOVE DECK TRIM SIDE RH PANEL ASSEMBLY 
  45. REMOVE ROOM LIGHT ASSEMBLY NO.2 
    1. Using a screwdriver, disengage the claw and remove the room light assembly No.2.

      HINT:

      Tape the screwdriver tip before use.

    2. Disconnect the connector.
    Fig 20: Disconnecting Connector
    G05281746Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  46. REMOVE ROOF SIDE LH GARNISH ASSEMBLY INNER 
    1. Using a screwdriver, remove the tonneau cover holder cap.

      HINT:

      Tape the screwdriver tip before use.

      Fig 21: Identifying Bolts And Tonneau Cover Holder Cap
      G05281747Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the 3 bolts.
    3. Using a clip remover, remove the 3 clips.
    4. Disengage the 7 clips and remove the roof side garnish assembly inner.
      Fig 22: Removing Roof Side Garnish Assembly Inner
      G05281748Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Disengage the 4 claws and separate the seat belt bezel.
      6. Fig 23: Removing Seat Belt Bezel
      G05281749Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  47. REMOVE ROOF SIDE RH GARNISH ASSEMBLY INNER 
  48. REMOVE TELEVISION BASE (w/Rear Seat Entertainment System)  (See REMOVAL )
  49. REMOVE TELEVISION DISPLAY ASSEMBLY (w/Rear Seat Entertainment System)  (See REMOVAL )
  50. REMOVE ASSIST GRIP SUB-ASSEMBLY 
    1. Using a screwdriver, disengage the 3 claws and remove the 2 assist grip covers.

      HINT:

      Tape the screwdriver tip before use.

      Fig 24: Removing Assist Grip Covers
      G05281750Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the 2 screws and assist grip sub-assembly.

    HINT:

    Use the same procedure for the other 3 assist grips.

  51. REMOVE RAIN SENSOR (w/Rain Sensor)  (See REMOVAL )
  52. REMOVE ROOM LIGHT ASSEMBLY NO.1 
    1. Using a screwdriver, disengage the 4 claws and remove the lens cover.

      HINT:

      Tape the screwdriver tip before use.

      Fig 25: Removing Lens Cover
      G05205616Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Using a screwdriver, disengage the 2 springs, as shown in the illustration.

      HINT:

      Tape the screwdriver tip before use.

      Fig 26: Removing Room Light Assembly No.1
      G05205617Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Disengage the 2 claws and remove the room light assembly No. 1.
    4. Disconnect the connector.
  53. REMOVE MAP LIGHT ASSEMBLY 
    1. w/o Sliding roof:

      Using a screwdriver, disengage the 6 claws and remove the lens cover.

      HINT:

      Tape the screwdriver tip before use.

      Fig 27: Removing Lens Cover Without Sliding Roof
      G05281753Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. w/Sliding roof:

      Using a screwdriver, disengage the 8 claws and remove the lens cover.

      HINT:

      Tape the screwdriver tip before use.

      Fig 28: Removing Lens Cover With Sliding Roof
      G05281754Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Using a screwdriver, disengage the claws and open the 2 caps, as shown in the illustration.

      HINT:

      Tape the screwdriver tip before use.

      Fig 29: Disengaging Claws And Open Caps
      G05281755Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Remove the 4 screws and map light.
      5. Fig 30: Removing Map Light With Screws
      G05281756Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Disconnect the connector.
  54. REMOVE LH VISOR ASSEMBLY 
    1. Using a molding remover, disengage the 4 claws and remove the visor bracket cover.
    2. Remove the 2 screws and visor assembly.
      3. Fig 31: Removing Screws And Visor Assembly
      G05281757Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Disconnect the connector.
  55. REMOVE RH VISOR ASSEMBLY 
  56. REMOVE VISOR HOLDER 
    1. Remove the visor holder by turning it counterclockwise.

      HINT:

      Use the same procedure to remove the other side.

    Fig 32: Identifying Sun Visor Holder
    G05244295Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  57. REMOVE ROOF HEADLINING ASSEMBLY 
    1. Disconnect the roof wire connector and disengage the clamps from the front pillar LH.
    2. Disconnect the washer hose. Remove the bolt and disconnect the radio antenna cord connector and disengage the clamps from the front pillar RH.
    3. Disconnect the washer hose. Disconnect the radio antenna cord connector and disengage the clamps from the rear quarter pillar RH.
    4. Disconnect the sliding roof drive gear connector. (w/sliding roof)
    5. Remove the sunroof opening trim molding. (w/sliding roof)
    6. Disengage the 2 fasteners and 3 clips. (w/o sliding roof)
    7. Disengage the 3 clips. (w/sliding roof)
      Fig 33: Identifying Fasteners
      G05281759Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    8. Remove the roof headlining from the vehicle through the back door side.
  58. REMOVE ROOF WIRE AND RADIO ANTENNA CORD 
    1. Remove the roof wire, radio antenna cord and washer hose from the roof headlining assembly.
    Fig 34: Identifying Roof Wire And Radio Antenna Cord
    G05281760Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
scientia non olet · About LEMON Manuals