Instrument Panel Safety Pad: Installation

HINT:

A bolt without a torque specification is shown in the standard bolt chart (see SPECIFIED TORQUE FOR STANDARD BOLTS ).

INSTALL INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY
1. Attach the 5 clips to install the safety pad.
2. Connect the connectors and clamps.
3. Install the 2 bolts to the passenger airbag.
  Torque: 20 N*m (204 kgf*cm, 15 ft.*lbf)
4. Install the 4 bolts, nut and 2 clips.
5. Install the center junction block RH and LH with the 4 nuts.
  
  Fig 1: Identifying Instrument Panel Safety Pad Clips And Bolts
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
6. w/ Navigation system:
  Install the navigation ECU.
  1. Connect the connector.
  2. Install the ECU with the 3 bolts.
    
    Fig 2: Identifying ECU With Bolts
    Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL MULTI-DISPLAY WITH RADIO RECEIVER ASSEMBLY (See INSTALLATION )
INSTALL FRONT PILLAR GARNISH LH (See INSTALLATION )
INSTALL FRONT PILLAR GARNISH RH (See INSTALLATION )
INSTALL GLOVE COMPARTMENT DOOR SUB-ASSEMBLY
1. Attach the 2 clips and claw to install the glove compartment door.
  
  Fig 3: Identifying Glove Compartment Door Clips
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Connect the connector and clamp.
3. Install the 4 screws.
INSTALL FRONT PASSENGER SIDE KNEE AIRBAG ASSEMBLY (See INSTALLATION )
INSTALL INSTRUMENT PANEL NO. 2 UNDER COVER SUB-ASSEMBLY
1. Connect the connector and clamp.
2. Attach the 4 clips to install the under cover.
Fig 4: Installing Instrument Panel No. 2 Under Cover
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL INTEGRATION CONTROL AND PANEL ASSEMBLY
1. Connect the connector.
2. Attach the 2 claws to install the control panel.
3. Install the 2 screws.
  
  Fig 5: Locating Screws And Integration Control Panel
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY (See INSTALLATION )
INSTALL INSTRUMENT PANEL NO. 1 SAFETY PAD SUB-ASSEMBLY
1. Install the hood lock control cable to the safety pad.
2. Attach the 8 clips and claw to install the safety pad.
Fig 6: Installing Instrument Panel No. 1 Safety Pad
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL INSTRUMENT PANEL NO. 1 UNDER COVER SUB-ASSEMBLY
1. Connect the connectors.
2. Attach the 3 claws to install the under cover.
3. Install the 2 screws.
Fig 7: Installing Instrument Panel No. 1 Under Cover
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL INSTRUMENT SIDE PANEL LH
1. Attach the 2 claws and 4 clips to install the side panel.
Fig 8: Installing Instrument Side Panel LH
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL INSTRUMENT SIDE PANEL RH
1. Attach the 2 claws and 4 clips to install the side panel.
Fig 9: Installing Instrument Side Panel RH
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL COMBINATION METER ASSEMBLY
1. Connect the connector.
2. Install the combination meter with the 4 screws.
Fig 10: Installing Combination Meter
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
1. Connect the connector.
2. Attach the 5 clips to install the cluster finish panel.
Fig 11: Installing Instrument Cluster Finish Panel
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL CONSOLE BOX
1. Connect the connector.
2. Install the console box with the 4 bolts and 2 screws.
Fig 12: Installing Console Box
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL CONSOLE BOX REGISTER ASSEMBLY
1. Attach the 4 clips to install the register.
Fig 13: Installing Console Box Register
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL CONSOLE BOX PLATE
1. Connect the connector.
2. Attach the 4 clips to install the console box.
Fig 14: Installing Console Box Plate
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL INSTRUMENT PANEL FINISH PANEL END LH
1. Attach the 4 clips and 3 claws to install the finish panel end.
2. Install the screw.
Fig 15: Installing Instrument Panel Finish Panel End LH
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL INSTRUMENT PANEL FINISH PANEL END RH
1. Attach the 3 clips and 3 claws to install the finish panel end.
2. Install the screw.
Fig 16: Installing Instrument Panel Finish Panel End RH
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL CONSOLE UPPER PANEL ASSEMBLY
1. Connect the connector.
2. Attach the 9 clips to install the ash receptacle.
  
  Fig 17: Identifying Clips
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Install the shift lever knob and twist it in the direction indicated by the arrow.
  
  Fig 18: Installing Shift Lever Knob
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL FRONT CONSOLE UPPER PANEL GARNISH
1. Attach the claws to install the garnish.
INSTALL HEADLIGHT DIMMER SWITCH ASSEMBLY (See INSPECTION )
INSTALL WINDSHIELD WIPER SWITCH ASSEMBLY (See INSTALLATION )
INSTALL SPIRAL CABLE WITH STEERING SENSOR (See INSTALLATION )
INSTALL STEERING COLUMN COVER UPPER
1. Install the steering column cover upper.
  For 3GR-FSE (see INSTALLATION )
  
  For 3UZ-FE (see INSTALLATION )
INSTALL STEERING COLUMN COVER LOWER
1. Install the steering column cover lower.
  For 3GR-FSE (see INSTALLATION )
  
  For 3UZ-FE (see INSTALLATION )
INSTALL STEERING WHEEL ASSEMBLY
1. Install the steering wheel assembly.
  For 3GR-FSE (see INSTALLATION )
  
  For 3UZ-FE (see INSTALLATION )
INSTALL STEERING PAD (See INSTALLATION )
INSTALL STEERING WHEEL NO. 3 COVER LOWER
INSTALL STEERING WHEEL NO. 2 COVER LOWER
INSTALL FRONT DOOR OPENING TRIM COVER LH (See INSTALLATION )
INSTALL FRONT DOOR OPENING TRIM COVER RH (See INSTALLATION )
INSTALL FRONT DOOR SCUFF PLATE LH (See INSTALLATION )
INSTALL FRONT DOOR SCUFF PLATE RH (See INSTALLATION )
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
PERFORM INITIALIZATION
NOTE: Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.
1. Perform initialization (see INITIALIZATION ).
CHECK SRS WARNING LIGHT
1. Check the SRS warning light (see DIAGNOSIS SYSTEM ).