Front Wiper Motor: Installation

1. Install the wiper motor with the 3 bolts.

   Torque: 5.4 N*m (55 kgf*cm, 47 in.*lbf) 

2. Apply MP grease to the crank arm pivot of the wiper motor.
   Fig 1: Locating Wiper Motor With Bolts

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Install the rod of the wiper link to the crank arm, as shown in the illustration.

Fig 2: Locating Rod Of Wiper Link To Crank Arm

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Install the wiper motor and link assembly with the 4 bolts.

   Torque: 5.5 N*m (56 kgf*cm, 49 in.*lbf) 

   Fig 3: Locating Wiper Motor And Link Assembly

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Connect the connector. Then attach the 2 clamps to install the wire harness to the cowl top panel.

Fig 4: Locating Connector

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Push the ventilator louver in the direction indicated by the arrow in the illustration. Attach the 10 claws to install the ventilator louver.
   Fig 5: Identifying Ventilator Louver

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Attach the 5 claws and 2 clips to install the ventilator louver.

Fig 6: Attaching 5 Claws And 2 Clips

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Push the cowl side seal in the direction indicated by the arrow in the illustration. Attach the 2 claws to install the cowl side seal.
   Fig 7: Locating Front Fender To Cowl Side Seal LH

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

HINT:

Use the same procedures described for the LH side.

1. Stop the wiper motor at the automatic stop position.
2. Clean the wiper arm serration with a round file or equivalent.
3. Clean the wiper pivot serration with a wire brush.
   Fig 8: Cleaning Wiper Pivot Serration With A Wire Brush

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
4. Install the wiper arm and blade with the nut. Make sure that the wiper arm and blade comes to the position shown in the illustration.

   Torque: 22 N*m (224 kgf*cm, 16 ft.*lbf) 

   HINT:

   Hold down the wiper arm hinge with your hand while tightening the nut.

   Specification 

   SPECIFICATION CHART
   
   

   Area	Measurement
   A	25.3 mm (0.996 in.)

Fig 9: Identifying Wiper Arm And Blade

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Stop the wiper motor at the automatic stop position.
2. Clean the wiper arm serration with a round file or equivalent.
3. Clean the wiper pivot serration with a wire brush.
   Fig 10: Cleaning Wiper Pivot Serration With A Wire Brush

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
4. Install the wiper arm and blade with the nut. Make sure that the wiper arm and blade comes to the position shown in the illustration.

   Torque: 22 N*m (224 kgf*cm, 16 ft.*lbf) 

   HINT:

   Hold down the wiper arm hinge with your hand while tightening the nut.

   Specifications 

   SPECIFICATION CHART
   
   

   Area	Measurement
   A	21.8 mm (0.858 in.)
   B	28.9 mm (1.138 in.)

   Fig 11: Identifying Wiper Arm And Blade

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
5. Operate the front wipers while spraying washer fluid on the windshield glass. Make sure that the front wipers function properly and there is no interference with the vehicle body.

1. Install the side cover with the 3 clips.

Fig 12: Identifying Engine Room Side Cover LH

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Attach the 3 clips to install the side seal.

Fig 13: Identifying Front Pillar To Front Side Seal RH

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

HINT:

Use the same procedures described for the LH side.

1. Perform initialization (see INITIALIZATION ).
   NOTE: Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.