Shift Solenoid Valve: Inspection

WARNING: This page is about a different variant/trim than selected.

INSPECT SHIFT SOLENOID VALVE SL1

Measure the resistance according to the value(s) in the table below.

Standard resistance

RESISTANCE SPECIFICATION

Tester Connection	Specified Condition 20°C (68°F)
1 - 2	5.0 to 5.6 Ω

Fig 1: Checking Resistance Between Shift Solenoid Valve SL1 Terminals

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Connect the positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector, then check the operation of the valve.
OK:

The solenoid makes an operating sound.

If the resistance is not within the specified range, replace the shift solenoid valve SL1.

INSPECT SHIFT SOLENOID VALVE S1

Measure the resistance according to the value(s) in the table below.

Standard resistance

RESISTANCE SPECIFICATION

Tester Connection	Specified Condition 20°C (68°F)
Solenoid Connector (S1) - Solenoid Body (S1)	11 to 15 Ω

Fig 2: Checking Resistance Between Shift Solenoid Valve S1 Terminal And Solenoid Body

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Connect the positive (+) lead to the terminal of the solenoid connector, and the negative (-) lead to the solenoid body, then check the operation of the valve.
OK:

The solenoid makes an operating sound.

If the resistance is not within the specified range, replace the shift solenoid valve S1.

INSPECT SHIFT SOLENOID VALVE S2

Measure the resistance according to the value(s) in the table below.

Standard resistance

RESISTANCE SPECIFICATION

Tester Connection	Specified Condition 20°C (68°F)
Solenoid Connector (S2) - Solenoid Body (S2)	11 to 15 Ω

Fig 3: Checking Resistance Between Shift Solenoid Valve S2 Terminal And Solenoid Body

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Connect the positive (+) lead to the terminal of the solenoid connector, and the negative (-) lead to the solenoid body.
OK:

The solenoid makes an operating noise.

If the resistance is not within the specified range, replace the shift solenoid valve S2.

INSPECT SHIFT SOLENOID VALVE S3

Measure the resistance according to the value(s) in the table below.

Standard resistance

RESISTANCE SPECIFICATION

Tester Connection	Specified Condition 20°C (68°F)
Solenoid Connector (S3) - Solenoid Body (S3)	11 to 15 Ω

Fig 4: Checking Resistance Between Shift Solenoid Valve S3 Terminal And Solenoid Body

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Connect the positive (+) lead to the terminal of the solenoid connector, and the negative (-) lead to the solenoid body, then check the operation of the valve.
OK:

The solenoid makes an operating sound.

If the resistance is not within the specified range, replace the shift solenoid valve S3.

INSPECT SHIFT SOLENOID VALVE S4

Measure the resistance according to the value(s) in the table below.

Standard resistance

RESISTANCE SPECIFICATION

Tester Connection	Specified Condition 20°C (68°F)
Solenoid Connector (S4) - Solenoid Body (S4)	11 to 15 Ω

Fig 5: Checking Resistance Between Shift Solenoid Valve S4 Terminal And Solenoid Body

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Connect the positive (+) lead to the terminal of the solenoid connector, and the negative (-) lead to the solenoid body.
OK:

The solenoid makes an operating sound.

If the resistance is not within the specified range, replace the shift solenoid valve S4.

INSPECT SHIFT SOLENOID VALVE SL2

Measure the resistance according to the value(s) in the table below.

Standard resistance

RESISTANCE SPECIFICATION

Tester Connection	Specified Condition 20°C (68°F)
1 - 2	5.0 to 5.6 Ω

Fig 6: Checking Resistance Between Shift Solenoid Valve SL2 Terminals

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Connect the positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector, then check the operation of the valve.
OK:

The solenoid makes an operating sound.

If the resistance is not within the specified range, replace the shift solenoid valve SL2.

INSPECT SHIFT SOLENOID VALVE SR

Measure the resistance according to the value(s) in the table below.

Standard resistance

RESISTANCE SPECIFICATION

Tester Connection	Specified Condition 20°C (68°F)
Solenoid Connector (SR) - Solenoid Body (SR)	11 to 15 Ω

Fig 7: Checking Resistance Between Shift Solenoid Valve SR Terminal And Solenoid Body

Connect the positive (+) lead to the terminal of the solenoid valve connector, and the negative (-) lead to the solenoid body, then check the operation of the valve.
OK:

The solenoid makes an operating sound.

If the resistance is not within the specified range, replace the shift solenoid valve SR.

INSPECT SHIFT SOLENOID VALVE SLT

Measure the resistance according to the value(s) in the table below.

Standard resistance

RESISTANCE SPECIFICATION

Tester Connection	Specified Condition 20°C (68°F)
1 - 2	5.0 to 5.6 Ω

Fig 8: Checking Resistance Between Shift Solenoid Valve SLT Terminals

Connect the positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector, then check the operation of the valve.
OK:

The solenoid makes an operating sound.

If the resistance is not within the specified range, replace the shift solenoid valve SLT.

INSPECT SHIFT SOLENOID VALVE SLU

Measure the resistance according to the value(s) in the table below.

Standard resistance

RESISTANCE SPECIFICATION

Tester Connection	Specified Condition 20°C (68°F)
1 - 2	5.0 to 5.6 Ω

Fig 9: Checking Resistance Between Shift Solenoid Valve SLU Terminals

Connect the positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector, then check the operation of the valve.
OK:

The solenoid makes an operating sound.

If the resistance is not within the specified range, replace the shift solenoid valve SLU.