LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2006 >> IS 250 RWD, Standard >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 1 (Automatic Transmission (A760H)) >> Torque Converter And Drive Plate >> Installation

Torque Converter And Drive Plate: Installation

WARNING: This page is about a different variant/trim than selected.
  1. INSTALL TORQUE CONVERTER CLUTCH ASSEMBLY (See  INSTALLATION   ) 
  2. INSTALL TRANSMISSION OIL COOLER (See step 2 in  INSTALLATION   ) 
  3. INSTALL TRANSMISSION CONTROL SHAFT LEVER LH (See step 3 in  INSTALLATION   ) 
  4. INSTALL TRANSFER DYNAMIC DAMPER (See step 4 in  INSTALLATION   ) 
  5. INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR (See step 5 in  INSTALLATION   ) 
  6. INSTALL AUTOMATIC WITH TRANSMISSION TRANSFER ASSEMBLY (See step 6 in  INSTALLATION   ) 
  7. INSTALL WATER BY-PASS HOSE (See step 7 in  INSTALLATION   ) 
  8. INSTALL WIRE HARNESS (See step 8 in  INSTALLATION   ) 
  9. CONNECT CONNECTOR (See step 9 in  INSTALLATION   ) 
  10. INSTALL ENGINE REAR MOUNTING MEMBER (See step 10 in  INSTALLATION   ) 
  11. INSTALL FLOOR SHIFT GEAR SHIFTING ROD SUB-ASSEMBLY (See step 11 in  INSTALLATION   ) 
  12. INSTALL NO. 1 EXHAUST PIPE SUPPORT BRACKET SUB-ASSEMBLY (See step 12 in  INSTALLATION   ) 
  13. INSTALL DRIVE PLATE & TORQUE CONVERTER CLUTCH SETTING BOLT (See step 13 in  INSTALLATION   ) 
  14. INSTALL STARTER ASSEMBLY (See  INSTALLATION  ) 
  15. INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY LH (See step 2 in  INSTALLATION  ) 
  16. INSTALL FRONT PROPELLER SHAFT ASSEMBLY (See  INSTALLATION  ) 
  17. INSTALL PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY (See  INSTALLATION  ) 
  18. INSTALL OUTSIDE AIR GUIDE PLATE RH (See step 4 in  INSTALLATION  ) 
  19. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL 
  20. ADJUST SHIFT LEVER POSITION (See  ADJUSTMENT   ) 
  21. INSPECT SHIFT LEVER POSITION (See  ON-VEHICLE INSPECTION   ) 
  22. INSTALL FRONT FLOOR NO. 1 HEAT INSULATOR (See step 3 in  INSTALLATION  ) 
  23. INSTALL FRONT EXHAUST PIPE ASSEMBLY (See step 4 in  INSTALLATION  ) 
  24. INSTALL OXYGEN SENSOR (See step 5 in  INSTALLATION  ) 
  25. INSTALL FRONT CENTER FLOOR BRACE (See step 7 in  INSTALLATION  ) 
  26. INSTALL NO. 1 REAR FLOOR PANEL BRACE (See step 8 in  INSTALLATION  ) 
  27. ADD COOLANT 

    (See step 5 in ON-VEHICLE INSPECTION )

  28. ADD AUTOMATIC TRANSMISSION FLUID 

    (See step 3 in ADJUSTMENT  )

  29. ADJUST COOLANT 

    (See ON-VEHICLE INSPECTION )

  30. CHECK FOR ENGINE COOLANT LEAKS (See  ON-VEHICLE INSPECTION  ) 
  31. CHECK FOR EXHAUST GAS LEAKS (See step 9 in  INSTALLATION  ) 
  32. INSTALL ENGINE UNDER COVER 
  33. INSTALL ENGINE ROOM SIDE COVER LH (See step 116 in  INSTALLATION  ) 
  34. INSTALL COOL AIR INTAKE DUCT SEAL (See step 118 in  INSTALLATION  ) 
  35. RESET MEMORY 

    (See INITIALIZATION  )

  36. PERFORM INITIALIZATION 

    Some systems need initialization after reconnecting the cable to the negative battery terminal

    (See INITIALIZATION ).

scientia non olet · About LEMON Manuals