Camshaft Timing Oil Control Valve Assembly: Installation

WARNING: This page is about a different car, the 2006 Lexus IS 350. However, it is still accessible from the selected car via links, so may be relevant.

INSTALL CAMSHAFT TIMING OIL CONTROL VALVE (for Bank 2 Intake Side)
1. Apply a light coat of engine oil to a new O-ring and install it to the oil control valve.
  
  Fig 1: Identifying Camshaft Timing Oil Control Valve O-Ring
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Install the oil control valve with the bolt.
  
  Fig 2: Identifying Camshaft Timing Oil Control Valve (For Bank 2 Intake Side)
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  
  Torque: 10 N*m (102 kgf*cm, 7 ft.*lbf)
  
  NOTE: Be careful that the O-ring is not cracked or jumped when installing the oil control valve.
3. Connect the camshaft timing oil control valve connector.
4. Install the bracket with the bolt.
  Torque: 10 N*m (104 kgf*cm, 7 ft.*lbf)
5. Connect the wiring harness at the bracket.
  
  Fig 3: Identifying Bracket
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL CAMSHAFT TIMING OIL CONTROL VALVE (for Bank 2 Exhaust Side)
1. Apply a light coat of engine oil to a new O-ring and install it to the oil control valve.
  
  Fig 4: Installing O-Ring To Oil Control Valve
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Install the oil control valve with the bolt.
  Torque: 10 N*m (102 kgf*cm, 7 ft.*lbf)
  
  NOTE: Be careful that the O-ring is not cracked or jumped when installing the oil control valve.
3. Connect the camshaft timing oil control valve connector.
  
  Fig 5: Identifying Camshaft Timing Oil Control Valve (For Bank 2 Exhaust Side)
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL CAMSHAFT TIMING OIL CONTROL VALVE (for Bank 1 Intake Side)
1. Apply a light coat of engine oil to a new O-ring and install it to the oil control valve.
  
  Fig 6: Identifying Camshaft Timing Oil Control Valve O-Ring
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Install the oil control valve with the bolt.
  Torque: 10 N*m (102 kgf*cm, 7 ft.*lbf)
  
  Fig 7: Identifying Camshaft Timing Oil Control Valve (For Bank 1 Intake Side)
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  
  NOTE: Be careful that the O-ring is not cracked or jumped when installing the oil control valve.
3. Connect the camshaft timing oil control valve connector.
4. Install the V-bank cover bracket with the bolt.
  Torque: 10 N*m (102 kgf*cm, 7 ft.*lbf)
INSTALL CAMSHAFT TIMING OIL CONTROL VALVE (for Bank 1 Exhaust Side)
1. Apply a light coat of engine oil to a new O-ring and install it to the oil control valve.
  
  Fig 8: Identifying Camshaft Timing Oil Control Valve O-Ring
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Install the oil control valve with the bolt.
  Torque: 10 N*m (102 kgf*cm, 7 ft.*lbf)
  
  NOTE: Be careful that the O-ring is not cracked or jumped when installing the oil control valve.
3. Connect the camshaft timing oil control valve connector.
  
  Fig 9: Identifying Camshaft Timing Oil Control Valve (For Bank 1 Exhaust Side)
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL INTAKE AIR SURGE TANK (See INSTALLATION )
INSTALL THROTTLE BODY (See INSTALLATION )
INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE (See INSTALLATION )
CONNECT NO. 2 VENTILATION HOSE (See INSTALLATION )
ADD ENGINE COOLANT (See COOLANT )
CHECK FOR ENGINE COOLANT LEAKS (See COOLANT )
INSTALL COWL TOP VENTILATOR LOUVER SUBASSEMBLY (See INSTALLATION )
INSTALL WINDSHIELD WIPER ARM AND BLADE ASSEMBLY RH (See INSTALLATION )
INSTALL WINDSHIELD WIPER ARM AND BLADE ASSEMBLY LH (See INSTALLATION )
INSTALL FRONT WIPER ARM HEAD CAP (See INSTALLATION )
INSTALL ROOF DRIP SIDE FINISH MOULDING RH (See INSTALLATION )
INSTALL ROOF DRIP SIDE FINISH MOULDING LH (See INSTALLATION )
INSTALL FRONT FENDER PROTECTOR UPPER RH (See INSTALLATION )
INSTALL FRONT FENDER PROTECTOR UPPER LH (See INSTALLATION )
INSTALL V-BANK COVER SUB-ASSEMBLY (See INSTALLATION )
INSTALL ENGINE ROOM SIDE COVER LH (See INSTALLATION )
INSTALL ENGINE ROOM SIDE COVER RH (See INSTALLATION )
INSTALL COOL AIR INTAKE DUCT SEAL (See INSTALLATION )