Typical Malfunction Thresholds

[OFF malfunction]

Both of the following condition are met: OFF malfunctions (A) and (B)

OFF malfunction (A) 

OFF malfunction (B) 

[ON malfunction]

One of the following conditions is met: ON malfunctions (A), (B) and (C)

ON malfunction (A) 

ON malfunction (B) 

ON malfunction (C) 

1. ACTIVE TEST 

   HINT:

   Performing the ACTIVE TEST using the intelligent tester allows the relay, VSV, actuator and so on to operate without parts removal. Performing the ACTIVE TEST as the first step of troubleshooting is one method to shorten labor time.

   It is possible to display the DATA LIST during the ACTIVE TEST.

   1. Warm up the engine.
   2. Turn the engine switch off.
   3. Connect the intelligent tester together with the CAN VIM (controller area network vehicle interface module) to the DLC3.
   4. Turn the engine switch on (IG) position.
   5. Turn on the tester.
   6. Select the item "DIAGNOSIS / ENHANCED OBD II / ACTIVE TEST / SHIFT".
   7. According to the display on the tester, perform the "ACTIVE TEST".

      HINT:

      While driving, the shift position can be forcibly changed with the intelligent tester.

      Comparing the shift position commanded by the ACTIVE TEST with the actual shift position enables you to confirm the problem (See DIAGNOSIS SYSTEM  ).

HINT:

• This test can be conducted when the vehicle speed is 50 km/h (31 mph) or less.
• The 4th to 5th and 5th to 6th up-shiftings must be performed with the accelerator pedal released.
• The 6th to 5th and 5th to 4th down-shiftings must be performed with the accelerator pedal released.
• Do not operate the accelerator pedal for at least 2 seconds after shifting and do not shift successively.
• The shift position commanded by the ECM is shown in the DATA LIST (SHIFT) display on the intelligent tester.
• The shift solenoid valve S3 is turned on/off normally when the shift lever is in the D position:
  SHIFT LEVER POSITION
  
  

  ECM command gearshift	1st	2nd	3rd	4th	5th	6th
  Shift solenoid valve S3	ON	ON	ON	OFF	OFF	OFF

1. CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P0761) 
   1. Connect the OBD II scan tool or the intelligent tester to the DLC3.
   2. Turn the engine switch on (IG) position and push the OBD II scan tool or the intelligent tester main switch ON.
   3. When you use intelligent tester:

      Select the item "DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODES".

   4. Read the DTCs using the intelligent tester.

      Result 

      DATA LIST
      
      

      Display (DTC output)	Proceed to
      Only "P0761" is output	A
      "P0761" and other DTCs	B

      HINT:

      If any other codes besides "P0761" are output, perform troubleshooting for those DTCs first.

   B : GO TO  DTC CHART  

   A : GO TO NEXT STEP 

2. PERFORM ACTIVE TEST BY INTELLIGENT TESTER (SHIFT SOLENOID VALVE SLT) 
   NOTE:

   • Perform the test at the normal operating ATF (Automatic Transmission Fluid) temperature: 50 to 80°C (122 to 176°F)
   • Be careful to prevent SST hose from interfering with the exhaust pipe.
   • This check must be conducted after checking and adjusting engine.
   • Perform under condition that A/C is OFF.

   HINT:

   Performing the ACTIVE TEST using the intelligent tester allows the relay, VSV, actuator and so on to operate without parts removal. Performing the ACTIVE TEST as the first step of troubleshooting is one method to shorten labor time. It is possible to display the DATA LIST during the ACTIVE TEST.

   1. Turn the engine switch off.
   2. Lift the vehicle up.
   3. Remove the test plug on the transmission case center right side and connect SST.

      SST 09992-00095 (09992-00231, 09992-00271) 

   4. Lower the vehicle.
   5. Fully apply the parking brake and chock the 4 wheels.
   6. Connect the intelligent tester together with the CAN VIM (controller area network vehicle interface module) to the DLC3.
   7. Start the engine.
   8. Warm up the ATF (Automatic Transmission Fluid).
   9. Measure the line pressure when the engine is idling.
   10. Turn on the tester.
   11. Select the item "DIAGNOSIS / ENHANCED OBD II / ACTIVE TEST / SOLENOID (SLT)".
   12. Follow the instructions on the tester and perform the ACTIVE TEST.
   13. Measure the line pressure with SST.
       Fig 1: Measuring Line Pressure With SST

       Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
       DATA LIST
       
       

       Item	Test Details
       SOLENOID (SLT)(1)	[Test Details] Operate the shift solenoid SLT and raise the line pressure. [Vehicle Condition] Vehicle Stopped. IDL: ON HINT: OFF: Line pressure up (When the active test of "SOLENOID (SLT)" is performed, the ECM commands the SLT solenoid to turn off). ON: No action (normal operation)
       (1) "SOLENOID (SLT)" in the ACTIVE TEST is performed to check the line pressure changes by connecting the SST to the automatic transmission, which is used in the HYDRAULIC TEST  as well.

       HINT:

       The pressure values in ACTIVE TEST and HYDRAULIC TEST are different from each other.

       OK: The line pressure changes as specified when performing the ACTIVE TEST. 

   NG : REPLACE SHIFT SOLENOID VALVE SLT 

   OK : GO TO NEXT STEP 

3. INSPECT SHIFT SOLENOID VALVE S3 
   1. Remove the shift solenoid valve S3.
   2. Measure the resistance according to the value(s) in the table below.

      Standard resistance 

      TESTER CONNECTION SPECIFIED CONDITION
      
      

      Tester Connection	Specified Condition 20°C (68°F)
      Solenoid Connector (S3) - Solenoid Body (S3)	11 to 15 Ω

   3. Connect the positive (+) lead to the terminal of the solenoid connector, and the negative (-) lead to the solenoid body.
      Fig 2: Inspecting Shift Solenoid Valve S3

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      OK: The solenoid makes an operating sound. 

   NG : REPLACE SHIFT SOLENOID VALVE S3 

   OK : GO TO NEXT STEP 

4. INSPECT TRANSMISSION VALVE BODY ASSEMBLY 

   OK: There are no foreign objects on each valve. 

   NG : REPLACE TRANSMISSION VALVE BODY ASSEMBLY 

   OK : REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLY