Front Wiper Motor: Removal

REMOVE COOL AIR INTAKE DUCT SEAL (See REMOVAL )
REMOVE ENGINE ROOM SIDE COVER LH (See Step 2 in REMOVAL )
REMOVE ENGINE ROOM SIDE COVER RH (See Step 3 in REMOVAL )
REMOVE FRONT UPPER FENDER PROTECTOR LH
1. Using a clip remover, separate the clip on the rubber portion of the cowl top ventilator louver sub-assembly from the front upper fender protector LH.
2. Disengage the 3 clips and the claw to remove the front upper fender protector LH.
Fig 1: Removing Front Upper Fender Protector LH
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
REMOVE FRONT UPPER FENDER PROTECTOR RH
HINT:

Use the same procedures for the RH side and the LH side.
REMOVE ROOF DRIP SIDE FINISH MOLDING LH (See REMOVAL )
REMOVE ROOF DRIP SIDE FINISH MOLDING RH
HINT:

Use the same procedures for the RH side and the LH side.
REMOVE FRONT WIPER ARM HEAD CAP
1. Using a screwdriver, remove the front wiper arm head cap.
  HINT:
  - Use the same procedures for the RH side and the LH side.
  - Tape the screwdriver tip before use.
Fig 2: Removing Front Wiper Arm Head Cap
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH
1. Remove the nut and the front wiper arm and blade assembly LH.
Fig 3: Removing Nut, Front Wiper Arm & Blade Assembly LH
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH
1. Remove the nut and the front wiper arm and blade assembly RH.
Fig 4: Removing Nut, Front Wiper Arm & Blade Assembly RH
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
REMOVE COWL TOP VENTILATOR LOUVER SUBASSEMBLY
1. Remove the 2 clips.
  
  Fig 5: Removing 2 Clips
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Disengage the 11 claws, and pull out the cowl top ventilator louver sub-assembly.
Fig 6: Pulling Out Cowl Top Ventilator Louver Sub-Assembly
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY
1. Disconnect the connector.
2. Remove the 2 bolts.
  
  Fig 7: Identifying Windshield Wiper Motor & Link Assembly Bolts
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Disengage the rubber pin of the windshield wiper motor from the vehicle body. Remove the windshield wiper motor and link assembly.
Fig 8: Disengaging Rubber Pin Of Windshield Wiper Motor From Vehicle Body
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
REMOVE WINDSHIELD WIPER MOTOR ASSEMBLY
1. Using a screwdriver, separate the windshield wiper No. 2 link rod from the crank arm pivot of the front wiper motor assembly.
  
  Fig 9: Separating Windshield Wiper No. 2 Link Rod From Crank Arm Pivot Of Front Wiper Motor Assembly
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  
  HINT:
  
  Tape the screwdriver tip before use.
2. Using a screwdriver, separate the windshield wiper No. 1 link rod from the pivot of the front wiper link assembly.
  
  Fig 10: Separating Windshield Wiper No. 1 Link Rod From Pivot Of Front Wiper Link Assembly
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  
  HINT:
  
  Tape the screwdriver tip before use.
3. Position the windshield wiper No. 1 link rod. Using a screwdriver, remove the windshield wiper No. 1 link rod.
  
  Fig 11: Positioning Windshield Wiper No. 1 Link Rod
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  
  HINT:
  
  Tape the screwdriver tip before use.
4. Using a "torx" socket wrench (T30), remove the 2 bolts and the windshield wiper motor assembly from the wind shield wiper link assembly.
Fig 12: Removing Bolts Of Windshield Wiper Motor Assembly
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002