Front Wiper Motor: Installation

1. Using a "torx" socket wrench (T30), install the windshield wiper motor assembly with the 2 bolts.

   Torque: 7.5 N*m (77 kgf*cm, 66 in.*lbf) 

   Fig 1: Identifying Windshield Wiper Motor Assembly Bolts

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Apply MP grease to the crank arm pivot of the windshield wiper motor assembly.
3. Install the windshield wiper link rod No. 1 to the crank arm pivot of the windshield wiper motor assembly.
   Fig 2: Installing Windshield Wiper Link Rod No. 1 To Crank Arm Pivot Of Windshield Wiper Motor Assembly

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
4. Apply MP grease to the pivot of the windshield wiper link assembly.
5. Install the windshield wiper link rod No. 1 to the pivot of the windshield wiper link assembly.
   Fig 3: Installing Windshield Wiper Link Rod No. 1 To Pivot Of Windshield Wiper Link Assembly

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
6. Install the windshield wiper link rod No. 2 to the crank arm pivot of the windshield wiper motor assembly.

Fig 4: Installing Windshield Wiper Link Rod No. 2 To Crank Arm Pivot Of Windshield Wiper Motor Assembly

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Install the windshield wiper motor and link assembly with the 2 bolts.

   Torque: 5.5 N*m (56 kgf*cm, 49 in.*lbf) 

   Fig 5: Identifying Windshield Wiper Motor & Link Assembly Bolts

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Connect the connector.

1. Engage the 11 claws.
   Fig 6: Engaging Claws

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Install the cowl top ventilator louver sub-assembly with the 2 clips.

Fig 7: Identifying Cowl Top Ventilator Louver Sub-Assembly With Clips

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Operate the wiper, and stop the windshield wiper motor at the automatic stop position.
2. Clean the wiper arm serrations.
3. Clean the wiper pivot serrations with a wire brush (when reinstalling).
   Fig 8: Cleaning Wiper Pivot Serrations With Wire Brush

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
4. Install the front wiper arm and blade assembly LH with the nut at the position as shown in Fig 9 .

Torque: 22 N*m (224 kgf*cm, 16 ft.*lbf) 

HINT:

Hold the arm hinge by hand to fasten the nut.

Fig 9: Installing Front Wiper Arm & Blade Assembly LH With Nut

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Operate the wiper, and stop the windshield wiper motor at the automatic stop position.
2. Clean the wiper arm serrations.
3. Clean the wiper pivot serrations with a wire brush (when reinstalling).
   Fig 10: Cleaning Wiper Pivot Serrations With A Wire Brush

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
4. Install the front wiper arm and blade assembly RH with the nut at the position as shown in Fig 11 .

   Torque: 22 N*m (224 kgf*cm, 16 ft.*lbf) 

   HINT:

   Hold the arm hinge by hand to fasten the nut.

   AREA MEASUREMENT REFERENCE TABLE
   
   

   Area	Measurement
   A	18.5 to 33.5 mm (0.73 to 1.32 in.)
   B	Approx. 20 mm (0.79 in.)

   Fig 11: Installing Front Wiper Arm & Blade Assembly RH With Nut

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
5. Operate the front wipers while spraying washer fluid on the windshield glass. Make sure that the front wipers function properly and there is no interference with the vehicle body.

1. Install the front wiper arm head cap.

Fig 12: Installing Front Wiper Arm Head Cap

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

HINT:

Use the same procedures for the RH side and the LH side.

1. Engage the claw and the 3 clips then install the front upper fender protector LH.
2. Engage the clip on the rubber portion of the cowl top ventilator louver sub-assembly to the front upper fender protector LH.

Fig 13: Installing Front Upper Fender Protector LH

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

HINT: 

Use the same procedures for the RH side and the LH side.