LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2006 >> GX 470 >> Repair and Diagnosis >> Body & Frame >> Seats >> Seat >> Rear No. 1 Seat LH >> Overhaul

Rear No. 1 Seat LH: Overhaul

  1. REMOVE REAR NO. 1 SEAT LH 
    1. Remove the headrest.
    2. Tumble the seat.
    3. Disengage the claws, remove the rear seat cushion hinge covers No. 2 LH and RH.
      Fig 1: Removing Rear Seat Cushion Hinge Covers No. 2 LH & RH
      G02962532Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Set the rear seat to the floor.
    5. Disengage the claws, remove the rear seat cushion hinge covers No. 3 LH and RH.
      Fig 2: Removing Rear Seat Cushion Hinge Covers No. 3 LH & RH & Disengaging Claws
      G02962533Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    6. Tumble the seat.
    7. Remove the 3 bolts, nut and the seat.
  2. REMOVE REAR SEAT CUSHION COVER LH 
    1. Using a screwdriver, remove the screw cover, screw and the release handle LH.
    2. Disengage the claws, remove the 2 screws and the reclining cover LH.
      Fig 3: Removing Reclining Cover LH
      G02962534Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Disengage the claws, remove the 2 screws and the reclining cover RH.
      Fig 4: Removing Reclining Cover RH
      G02962535Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Disengage the seatback cover hem.
      Fig 5: Disengaging Seatback Cover Hem
      G02962536Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Insert a screwdriver between the seat cushion cover and seat cushion under cover.
      Fig 6: Inserting Screwdriver Between Seat Cushion Cover & Seat Cushion Under Cover
      G02962537Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      NOTE: Tape the screwdriver tip before use.
    6. Pry the seat cushion cover hem to disengage it.
    7. Cut the hog rings and bring out the seat cushion cover together with the pad.
    8. Remove the nut and disconnect the rear seat 3 point type seat belt assy LH.
    9. Remove the seat cushion cover together with the pad.
    10. Cut the hog rings and remove the seat cushion cover from the pad.
  3. REMOVE REAR SEAT ARMREST ASSY CENTER 
    1. Open the fastener of the seatback cover.
    2. Remove the screw and the armrest cover.
    3. Remove the 3 bolts, guide, armrest hinge and the armrest.
  4. REMOVE REAR SEATBACK ASSY LH 
    1. Disconnect the seat lock control cables from the seatback frame.
    2. Remove the 3 bolts, washer, grommet and the seatback stopper plate.
    3. Disengage the claws, remove the 2 screws and the 2 reclining covers.
    4. Remove the 4 bolts and the rear seatback assy LH.
    Fig 7: Removing Rear Seatback Assy LH
    G02962538Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  5. REMOVE REAR SEATBACK COVER LH 
    1. Remove the 2 tether anchor covers.
    2. Remove the rear seat protector.
    3. Push the claws and remove the 4 headrest supports.
    4. Remove the rear seat shoulder belt hole cover.
    5. Remove the seatback cover together with the pad.
    6. Cut the hog rings and remove the seatback cover.
      Fig 8: Removing Rear Seat Back Cover LH
      G02962539Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  6. REMOVE REAR SEAT 3 POINT TYPE BELT ASSY LH 
    1. Remove the 2 screws and the reclining adjuster cover sub-assy.
    2. Using a screwdriver, remove the rear seat shoulder belt hole cover.
    3. Remove the 2 nuts, 2 screws and the seat belt.
  7. REMOVE REAR SEAT HINGE SUB-ASSY LH 
    1. Using a screwdriver, remove the spring of the seat stay ball-joint.
    2. Disconnect the ball-joint from the seat cushion frame.
    3. Remove the hinge cover, E-ring, pin, hinge guide, spring and the hinge together with the seat stay.
      Fig 9: Removing Rear Seat Hinge Sub-Assy LH
      G02962540Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  8. REMOVE REAR SEAT HINGE SUB-ASSY RH 
    1. Remove the hinge cover, E-ring, pin, hinge guide and the hinge.
  9. REMOVE REAR SEAT CUSHION UNDER COVER SUB-ASSY LH 
    1. Remove the 7 screws, cushion and the cover.
  10. REMOVE REAR SEAT BELT INNER 
    1. Remove the nut and rear seat belt inner.
    2. Remove the nut and rear seat belt inner No. 2.
  11. REMOVE FOLD SEAT LOCK CONTROL CABLE ASSY NO. 2 
  12. REMOVE REAR NO. 1 SEAT LOCK CABLE ASSY 
  13. REMOVE REAR SEAT RECLINING CONTROL WIRE SUB-ASSY 
  14. INSTALL FOLD SEAT LOCK CONTROL CABLE ASSY NO. 2 
  15. INSTALL REAR SEAT BELT INNER 
    1. Install the rear seat belt inner No. 2 with the nut.

      Torque: 42 N.m (430 kgf.cm, 31 ft.lbf) 

    2. Install the rear seat belt inner with the nut.

      Torque: 42 N.m (430 kgf.cm, 31 ft.lbf) 

  16. INSTALL REAR SEAT CUSHION UNDER COVER SUB-ASSY LH 
    1. Install the cover with the 6 screws.
    2. Install the cushion with the screw.
  17. INSTALL REAR SEAT HINGE SUB-ASSY RH 
    1. Install the hinge guide to the hinge.
    2. Install the hinge with the pin and new E-ring.
    3. Install the hinge cover.
  18. INSTALL REAR SEAT HINGE SUB-ASSY LH 
    1. Install the spring to the ball-joint of the seat stay.
    2. Connect the ball-joint to the seat cushion frame securely.
    3. Install the spring and hinge guide to the hinge.
    4. Install the hinge with the pin and new E-ring.
    5. Install the hinge cover.
  19. INSTALL NO. 1 SEAT 3 POINT TYPE BELT ASSY LH 
    1. Install the seat belt with the 2 nuts and 2 screws.
    2. Install the rear seat shoulder belt hole cover.
    3. Install the reclining adjuster cover sub-assy with the 2 screws.
  20. INSTALL REAR SEATBACK COVER LH 
    1. Install the seatback cover to the seatback pad with new hog rings.
    2. Install the seatback cover together with the pad to the seatback frame.
    3. Install the 2 headrest supports.
      NOTE: Be careful not to mistake the headrest support direction.
    4. Connect the rear seat lock cable to the rear seat reclining cover.
    5. Install the rear seat protector.
    6. Install the 2 tether anchor covers.
  21. INSTALL REAR SEATBACK ASSY LH 
    1. Install the rear seatback assy LH with the 4 bolts.

      Torque: 50 N.m (510 kgf.cm, 37 ft.lbf) 

    2. Install the 2 reclining covers with the 2 screws.
    3. Install the seatback stopper plate to the seat cushion frame with the 2 bolts.
    4. Install the grommet, washer and the bolt.
    5. Connect the seat lock control cables to the seatback frame.
      Fig 10: Installing Rear Seatback Assy LH
      G02962541Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  22. INSTALL REAR SEAT ARMREST ASSY CENTER 
    1. Install the armrest.
    2. Install the guide to the armrest hinge.
    3. Install the armrest hinge with the 3 bolts.
    4. Install the armrest cover with the screw.
    5. Close the fastener of the seatback cover.
  23. INSTALL REAR SEAT CUSHION COVER LH 
    1. Install the seat cushion cover to the seat cushion pad with new hog rings.
    2. Install the No .1 seat 3 point type belt through the seat cushion pad.
    3. Install the No .1 seat 3 point type belt with the bolt.

      Torque: 42 N.m (430 kgf.cm, 31 ft.lbf) 

    4. Install the seat cushion cover together with the pad to the seat cushion frame with new hog rings.
    5. Securely engage the seat cushion cover hem to the seat cushion under cover.
      Fig 11: Engaging Seat Cushion Cover Hem To Seat Cushion Under Cover
      G02962542Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    6. Engage the seatback cover hem.
      Fig 12: Engaging Seatback Cover Hem
      G02962543Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    7. Install the reclining cover RH with the 2 screws.
      Fig 13: Installing Reclining Cover RH With Screws
      G02962544Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    8. Install the reclining cover LH with the 2 screws.
      Fig 14: Installing Reclining Cover LH
      G02962545Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    9. Install the release handle LH with the screw.
    10. Install the screw cover.
  24. INSTALL REAR NO. 1 SEAT LH 
    1. Install the seat with the 3 bolts and the nut.

      Torque: 37 N.m (375 kgf.cm, 27 ft.lbf) 

    2. Set the rear seat to the floor.
    3. Install the rear seat cushion hinge covers No. 3 LH and RH.
      Fig 15: Installing Rear Seat Cushion Hinge Covers No. 3 LH & RH
      G02962546Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Tumble the seat.
    5. Install the rear seat cushion hinge covers No. 2 LH and RH.
      Fig 16: Installing Rear Seat Cushion Hinge Covers No. 2 LH & RH
      G02962547Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    6. Install the headrest.
scientia non olet · About LEMON Manuals