LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2000 >> SC 400 >> Repair and Diagnosis (Single Page) >> Restraints >> Air Bag, SRS >> Air Bag Restraint Systems >> Diagnostic Tests >> DTC 11-B0102: Short To Ground In Driver-Side Air Bag Squib Circuit Or Passenger-Side Air Bag Squib Circuit >> Diagnostic Procedure

Diagnostic Procedure

  1. Disable air bag system. See DISABLING SYSTEM  under DISABLING & ACTIVATING AIR BAG SYSTEM.
  2. Measure resistance between ground and Red on spiral cable side of wire of upper spiral cable connector (circuit D+). See WIRING DIAGRAMS . If resistance is more than one megohm, go to next step. If resistance is less than one megohm, go to step  7.
  3. Measure resistance between ground and Blue wire on air bag sensor assembly side of passenger-side air bag module harness connector (circuit P+). If resistance is more than one megohm, go to next step. If resistance is less than one megohm, repair or replace harness or connector between passenger-side air bag module and air bag sensor assembly.
  4. Reconnect air bag sensor assembly connector. Connect jumper wire between Red wire and White wire on spiral cable side of upper spiral cable connector. Connect jumper wire between Blue wire and Yellow wire on air bag sensor assembly side of passenger-side air bag module harness connector. Connect negative battery cable. Wait at least 2 seconds. Turn ignition switch to ACC or ON position. Wait at least 20 seconds. Clear DTCs. See CLEARING CODES  under DIAGNOSTICS. Turn ignition switch to LOCK position. Wait at least 20 seconds. Turn ignition switch to ACC or ON position. Wait at least 20 seconds. Retrieve codes. See RETRIEVING CODES  under DIAGNOSTICS. If DTC 11-B0102 is displayed, replace air bag sensor assembly. If DTC 11-B0102 is not displayed, go to next step.
  5. Turn ignition switch to LOCK position. Disconnect negative battery cable. Wait at least 90 seconds. Reconnect upper spiral cable connector to driver-side air bag module. Reconnect negative battery cable. Wait at least 2 seconds. Turn ignition switch to ACC or ON position. Wait at least 20 seconds. Clear DTCs. See CLEARING CODES  under DIAGNOSTICS. Turn ignition switch to LOCK position. Wait at least 20 seconds. Turn ignition switch to ACC or ON position. Wait at least 20 seconds. Retrieve codes. See RETRIEVING CODES  under DIAGNOSTICS. If DTC 11-B0102 is displayed, replace driver-side air bag module. If DTC 11-B0102 is not displayed, go to next step.
  6. Turn ignition switch to LOCK position. Disconnect negative battery cable. Wait at least 90 seconds. Reconnect passenger-side air bag module connector. Reconnect negative battery cable. Wait at least 2 seconds. Turn ignition switch to ACC or ON position. Wait at least 20 seconds. Clear DTCs. See CLEARING CODES  under DIAGNOSTICS. Turn ignition switch to LOCK position. Wait at least 20 seconds. Turn ignition switch to ACC or ON position. Wait at least 20 seconds. Retrieve codes. See RETRIEVING CODES  under DIAGNOSTICS. If DTC 11-B0102 is displayed, replace passenger-side air bag module. If DTC 11-B0102 is not displayed, system is functioning properly at this time. Check for intermittent fault. See AIR BAG WARNING LIGHT INTERMITTENT .
  7. Disconnect lower spiral cable connector. Measure resistance between ground and Red wire on spiral cable side of upper spiral cable connector. If resistance is more than one megohm, go to next step. If resistance is less than one megohm, replace spiral cable.
  8. Measure resistance between ground and Red wire on air bag sensor assembly side of lower spiral cable connector. If resistance is less than one megohm, replace or replace wiring harness or connector between spiral cable and air bag sensor assembly. If resistance is more than one megohm, system is functioning properly at this time. Check for intermittent fault. See AIR BAG WARNING LIGHT INTERMITTENT .
scientia non olet · About LEMON Manuals