LEMON Manuals: Even more car manuals for everyone
Home >> Land Rover >> 2022 >> Range Rover Evoque SE >> Repair and Diagnosis >> Suspension >> Rear Suspension -- Range Rover EVOQUE/L551 >> Rear Suspension >> Removal And Installation >> Rear SUBFRAME - [+] PHEV (G2919873) >> Removal

Rear SUBFRAME - [+] PHEV (G2919873): Removal

WARNING: This procedure can only be completed after the vehicle has been powered down by an approved person.
NOTE:
  • This procedure contains some variation in the illustrations depending on the vehicle specification, but the essential information is always correct.
  • This procedure contains illustrations showing certain components removed to provide extra clarity.
  1. WARNING: Jaguar Land Rover (JLR) Electric Vehicle Competent Person (EVCP) trained technicians only.
    G12528294Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    This procedure involves work on components associated with the High Voltage (HV) system. Only technicians qualified to Electric Vehicle Authorized Person (EVAP) level or higher are allowed to perform this procedure. It is mandated that all technicians involved with the steps in this procedure have read and understood the Electric Vehicle Safety Rules.

    Refer to: ELECTRIC VEHICLE SAFETY RULES (G2408927)

  2. Raise and support the vehicle on a suitable 2 post lift.

    Refer to: JACKING AND LIFTING .

  3. WARNING: JLR EVAP  trained technicians only.
    G12528295Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Power Down the HV  system. Only technicians qualified to EVAP  level or higher are allowed to perform this procedure. It is mandated that all technicians involved with the steps in this procedure have read and understood the Electric Vehicle Safety Rules.

    Refer to: PHEV POWER DOWN/UP -- COMPLETE VEHICLE - PATHFINDER (G2770157)

  4. Remove the Electric Rear Axle Drive (eRAD).

    Refer to: ELECTRIC REAR AXLE DRIVE .

  5. G14913386Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Remove the 10 bolts.
    • Remove the 9 fasteners.
    • Remove the right side undershield.
  6. G14913387Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Remove the 2 bolts.
    • Release the air deflector from the clip.
    • Remove the air deflector.
  7. NOTE: Repeat the step for the other side.
    G14913354Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Remove the nut.
    • Release and position the brake pipes to one side.
  8. G14913355Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Disconnect the 3 electrical connectors from the body harness.
    • Release the 2 wiring harness clips.
  9. G14913356Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Release the subframe wiring harness from the 3 fasteners.

  10. G14913357Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Remove the fuel filler pipe bracket bolt.

  11. NOTE: Repeat the step for the other side.
    G14913392Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Remove the bolt.
    • Remove the heatshield.
  12. G14913393Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    To aid installation, use a straight edge to mark the position of the subframe in relation to the body at the points shown.

  13. G14913394Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Remove and discard the 4 subframe bracket nuts and bolts.

  14. WARNING: This step requires the aid of another technician.
    G14913395Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Use a suitable transmission jack to support the rear subframe.

      General Equipment: Transmission jack 

    • Remove and discard the 4 subframe to body bolts.
    • Remove the rear subframe.
  15. NOTE: Do not disassemble further if the component is removed for access only.
    G14913396Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Remove the 2 rear springs.

  16. G14456479Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Disconnect the 4 electrical connector.
    • Release the 17 wiring harness clips.
    • Release the 8 wiring harness grommets.
    • Remove the rear subframe wiring harness.
  17. G14913398Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Remove and discard the 4 bolts.
    • Remove the rear stabilizer bar assembly.
  18. G14913399Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Remove the bolt.
    • Release the wiring harness grommet.
  19. G14913400Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Remove the 2 bolts.
    • Remove the rear height sensor.
  20. NOTE: Repeat the step for the other side.
    G14913401Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Remove and discard the nut and bolt.
    • Remove the rear upper control arm.
  21. NOTE: Repeat the step for the other side.
    G14913402Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Remove and discard the 2 nuts and bolts.
    • Remove the rear lower control arm.
  22. NOTE: Repeat the step for the other side.
    G14913403Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Remove and discard the nut and bolt.
    • Remove the rear tie-rod.
  23. G14913373Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Remove the nut.
    • Remove the Noise, Vibration and Harshness (NVH) damper.
scientia non olet · About LEMON Manuals