General Equipment

WARNING: This page is about a different variant/trim than selected.

EQUIPMENT NAME
Engine stand
Hydraulic jib crane

WARNING: Be prepared to collect escaping engine coolant.

CAUTION:

Be prepared to collect escaping fuel.
Be prepared to collect escaping oil.
Before disconnecting any components, make sure the area is clean and free from foreign material. When disconnected all openings must be sealed.

NOTE:

This procedure contains some variation in the illustrations depending on the vehicle specification, but the essential information is always correct.
This procedure contains illustrations showing certain components removed to provide extra clarity.

Always follow the Petrol and Petrol-Ethanol Fuel Systems Health and Safety Precautions, before any repairs are done to the fuel system.
Refer to: PETROL AND PETROL-ETHANOL FUEL SYSTEMS HEALTH AND SAFETY PRECAUTIONS
Raise and support the vehicle on a suitable 2 post lift.
Refer to: JACKING AND LIFTING
Disconnect the startup battery ground cable.
Refer to: 12V SYSTEM DISCONNECT AND CONNECT
Remove the hood.
Refer to: HOOD
Remove the transmission.
Refer to: TRANSMISSION - INGENIUM I4 2.0L PETROL
Remove the Air Conditioning (A/C) compressor.
Refer to: AIR CONDITIONING COMPRESSOR - INGENIUM I4 2.0L PETROL
Remove the secondary bulkhead center panel.
Refer to: SECONDARY BULKHEAD CENTER PANEL - INGENIUM I4 2.0L PETROL/INGENIUM I4 2.0L PETROL - PHEV/INGENIUM I6 3.0L DIESEL/INGENIUM I6 3.0L PETROL
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
- Disconnect the electrical connector.
- Release the wiring harness clip.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Disconnect the engine coolant hose.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Disconnect the 2 engine coolant hoses.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Disconnect the 2 engine coolant hoses.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
- Disconnect the Low Pressure (LP) fuel line.
- Disconnect the breather pipe.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
- Remove the 2 bolts.
- Remove the closing panel.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
- Release the bolt.
- Disconnect the 2 electrical connectors.
- Release the wiring harness clip.
- Release the wiring harness grommet.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
- Install the special tool.
  Special Tool(s): JLR-303-1633-01
- Install and tighten the 2 bolts.
  Torque : 25 Nm
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Remove and discard the nut.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Remove and discard the nut.
WARNING: This step requires the aid of another technician.

Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
- Install the special tool.
  Special Tool(s): JLR-303-1633-01
- Use the special tool and a suitable hydraulic jib crane to carefully remove the engine.
  General Equipment: Hydraulic jib crane
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
- Remove the 4 bolts.
- Remove the bracket.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
- Install the special tool.
  Special Tool(s): JLR-303-1673
- Install and tighten the 4 bolts.
  Torque : 40 Nm
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
- Install the engine assembly onto a suitable engine stand.
  General Equipment: Engine stand
- Remove the hydraulic jib crane.
  General Equipment: Hydraulic jib crane
- Remove the special tool.
  Special Tool(s): JLR-303-1633-01