Special Tool(S)

WARNING: This page is about a different variant/trim than selected.

G11675175

Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

100-012
Slide Hammer

G11707841

Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

100-012-01
Slide Hammer Adapter

G11714691

Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

JLR-303-1630
Locking Tool, Crankshaft Pulley

G11718424

Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

JLR-310-254
Injector Remover

WARNING:

Be prepared to collect escaping fuel.
Be prepared to collect escaping oil.
Be prepared to collect escaping coolant.

CAUTION:

All the components removed from the old engine must be cleaned and inspected before installing to the new engine. Any worn or damaged components or retaining clips must be replaced.
Note the orientation of the components prior to removal.
New engines may be supplied with untapped bolt holes for some of the components. Reuse bolts from the original engine, as these are self tapping and will cut threads where required.
Before disconnecting any components, make sure the area is clean and free from foreign material. When disconnected all openings must be sealed.

NOTE:

This procedure contains some variation in the illustrations depending on the vehicle specification, but the essential information is always correct.
This procedure contains illustrations showing certain components removed to provide extra clarity.

Always follow the fuel system health and safety precautions, when preforming any repairs to the fuel system.
Refer to: PETROL AND PETROL-ETHANOL FUEL SYSTEMS HEALTH AND SAFETY PRECAUTIONS
Raise and support the vehicle on a suitable 2 post lift.
Refer to: JACKING AND LIFTING
WARNING: Jaguar Land Rover (JLR) Electric Vehicle Competent Person (EVCP) trained technicians only.

Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

This procedure involves work on components associated with the High Voltage (HV) system. Only technicians qualified to EVCP level or higher are allowed to perform this procedure. It is mandated that all technicians involved with the steps in this procedure have read and understood the Electric Vehicle Safety Rules.

Refer to: DESCRIPTION AND OPERATION .
Disconnect the 12 V system.
Refer to: 12V SYSTEM DISCONNECT AND CONNECT
Remove the engine assembly.
Refer to: REMOVAL .
Support the engine on a suitable stand.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Install the special tool.

Special Tool(s): JLR-303-1630
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Remove the drive plate. Discard the bolts.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Remove the engine mounting brackets.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Remove and discard the crankshaft pulley bolts.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Remove the special tool.

Special Tool(s): JLR-303-1630
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Remove the crankshaft pulley.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Remove the drain plug and allow engine oil to drain into a suitable container.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Remove the Noise, Vibration and Harshness (NVH) material.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Remove the breather.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Remove the coolant hose.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Remove the vacuum pipe assembly.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Disconnect and release the coolant hose.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Remove the oil level gauge assembly. Discard the O-ring seal.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Remove the coolant hose.
CAUTION: Take care when disconnecting and releasing the wiring harness.

Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Disconnect and release the wiring harness.
CAUTION: Take care when disconnecting and releasing the wiring harness.

Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Disconnect and release the wiring harness.
CAUTION: Take care when disconnecting and releasing the wiring harness.

Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Disconnect and release the wiring harness.
CAUTION: Take care when disconnecting and releasing the wiring harness.

Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Disconnect and release the wiring harness.
CAUTION: Note the original routing of the wiring harness prior the removal.

Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Remove the wiring harness.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Remove both fuel supply pipes.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Remove the purge valve.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
- Release the knock sensor wiring harness.
- Remove the intake manifold. Discard the seals.
CAUTION: Note the orientation of the knock sensors prior to removal.

Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Remove the knock sensors.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Remove the thermostat housing. Discard the gasket.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Remove the coolant pump pulley.
NOTE:
- This component uses self tapping bolts. These bolts must be kept to cut the thread on the new engine as they may be supplied with untapped bolt holes.
- Inspect the coolant pump seal for damage. If any damage is visible, a new coolant pump must be installed.
- If no seal damage is visible, the coolant pump is to be fitted to the new engine.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Remove the coolant pump.
NOTE: Note the orientation of the oil supply hose prior to removal.

Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Disconnect the turbocharger oil supply hose. Discard the sealing washers.
NOTE: Note the orientation of the oil supply hose prior to removal.

Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Remove the turbocharger oil supply hose. Discard the sealing washers.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Disconnect the turbocharger coolant supply and return hoses. Inspect the O-ring seals, discard the components if damaged or worn.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Remove the coolant degas separator. Discard the o-ring seal.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Remove the turbocharger lower heatshield.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Remove the turbocharger heatshield.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Remove the turbocharger oil return pipe. Discard the 2 o-ring seals.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Remove the turbocharger. Discard the nuts and gasket.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Remove the coolant pump inlet pipe. Discard the O-ring seal.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Remove the crankshaft position sensor.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Remove the camshaft position sensors. Discard the 2 O-ring seals.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Remove the variable valve timing solenoids. Discard the 2 O-ring seals.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Remove the oil filler neck. Discard the O-ring seal.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Remove the engine lifting eye.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Remove the ignition coil-on-plugs.
CAUTION: Take care when disconnecting and removing the wiring harness.

Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Release the fuel injector wiring harness.
CAUTION: Loosen each of the bolts 1 turn at a time until the spring tension is fully released.

Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Remove the fuel rail.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Remove the fuel injector wiring harness.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Remove and discard the 4 fuel injector spring clamps.
CAUTION: Make sure that the special tool is correctly installed.

Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Install the special tool to the fuel injector.

Special Tool(s): JLR-310-254
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Using the special tools, remove the injector.

Special Tool(s): 100-012 , 100-012-01 , JLR-310-254
CAUTION: Do not use any sharp tools to remove the O-ring seal as damage could occur to the fuel injector.

Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Remove and discard the O-ring seals.
CAUTION:
- Do not use a knife to remove the Teflon seal as damage could occur to the fuel injector.
- Pinch the Teflon seal to allow the tool to cut the Teflon seal without damaging the fuel injector.
- Do not cut the Teflon seal too deep as damage could occur to the fuel injector.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Remove and discard the Teflon seal.
Repeat steps 57 to 60 for the remaining injectors.
CAUTION: Loosen each of the bolts 1 turn at a time until the spring tension is fully released.

Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Remove the high pressure fuel pump. Discard the bolts.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Remove the purge valve mounting bracket.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Install the drain plug.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Remove the NVH material.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Remove the NVH material.
NOTE: If equipped.

Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Remove the block heater.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Remove the engine vent oil separator. Discard the gasket.