LEMON Manuals: Even more car manuals for everyone
Home >> Land Rover >> 2022 >> Defender 110 S >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 26 (Fuel Charging And Controls - V8 S/C 5.0L Petrol -- Defender/L663) >> Fuel Charging And Controls - V8 S/C 5.0L Petrol (G2796609) >> Removal And Installation >> High Pressure Fuel Pump 1 (G2796614) >> Removal

High Pressure Fuel Pump 1 (G2796614): Removal

WARNING: This page is about a different variant/trim than selected.
WARNING:
  • This procedure involves fuel handling, be prepared for fuel spillage at all times and always observe fuel handling precautions. Failure to follow these instructions may result in personal injury.
  • Be prepared to collect escaping fuel.
CAUTION: Before disconnecting any components, make sure the area is clean and free from foreign material. When disconnected all openings must be sealed.
NOTE:
  • This procedure contains some variation in the illustrations depending on the vehicle specification, but the essential information is always correct.
  • This procedure contains illustrations showing certain components removed to provide extra clarity.

The following step(s) applies to: 

All vehicles 

  1. Before working on the fuel system make sure to study the fuel system health and safety.

    Refer to: PETROL AND PETROL-ETHANOL FUEL SYSTEMS HEALTH AND SAFETY PRECAUTIONS

  2. Release the fuel pressure.

    Refer to: FUEL SYSTEM PRESSURE RELEASE

  3. Disconnect the 12 V system.

    Refer to: 12V SYSTEM DISCONNECT AND CONNECT

  4. Raise and support the vehicle on a suitable 2 post lift.

    Refer to: JACKING AND LIFTING

  5. Remove the starter motor.

    Refer to: STARTER MOTOR

  6. Remove the generator.

    Refer to: GENERATOR

  7. Remove the air cleaner outlet pipe T-connector.

    Refer to: AIR CLEANER OUTLET PIPE T-CONNECTOR

  8. CAUTION: Be prepared to collect escaping coolant.
    G15312156Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Release the 2 clips.
    • Disconnect the 5 coolant pipe connectors.
    • Remove the coolant pipe assembly.
    • Release the coolant pipe assembly and position to one side.
  9. G15312157Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Remove the 2 nuts.
    • Release the cable bracket assembly from the valve cover.
  10. G15312158Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Disconnect the electrical connector.
    • Release the clip.
    • Remove the bolt.
    • Disconnect the hose.
    • Remove the right differential pressure sensor assembly.
  11. G15312159Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Release the vacuum pipe from the right coil cover and position to one side.

  12. G15305904Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Release the 3 upper clips.
    • Release the stud.
    • Release the 4 lower clips.
    • Remove the right coil cover.
  13. G14051949Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Disconnect the electrical connector.
    • Release the clip.
    • Remove the 2 nuts.
    • Disconnect the hose.
    • Remove the left differential pressure sensor assembly.
  14. WARNING: Be prepared to collect escaping fuel.
    CAUTION: Before disconnecting any components, make sure the area is clean and free from foreign material. When disconnected all openings must be sealed.
    G15305902Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Release the 2 fuel line clips.
    • Release the 2 fuel lines from the left coil cover.
    • Disconnect the 2 fuel line connectors.
  15. G15305903Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Remove the oil filler cap.
    • Release the 2 lower studs.
    • Release the 2 upper clips.
    • Remove the left coil cover.
    • Install the oil filler cap.
  16. G15312164Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Disconnect the breather pipe connector.
    • Release the clip.
    • Position the breather pipe to one side.
  17. G15312165Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Disconnect the 4 electrical connectors.
    • Release the 2 clips.
    • Position the wiring harness to one side.
  18. WARNING: Be prepared to collect escaping fuel.
    CAUTION: Before disconnecting any components, make sure the area is clean and free from foreign material. When disconnected all openings must be sealed.
    G15304166Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Loosen the 2 fuel crossover line unions.
    • Remove the 4 bolts.
    • Disconnect the 2 fuel crossover line unions.
    • Remove the fuel crossover line.
  19. G15304207Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Release the clip.
    • Position the wiring harness to one side.
  20. WARNING: Be prepared to collect escaping fuel.
    CAUTION: Before disconnecting any components, make sure the area is clean and free from foreign material. When disconnected all openings must be sealed.
    G15304208Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Remove the nut.
    • Disconnect the High Pressure (HP) fuel line union.

    The following step(s) applies to: 

    Right hand drive vehicles 

  21. G15322221Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Remove and discard the steering column lower shaft lower bolt.
    • Reposition the steering column shaft.

    The following step(s) applies to: 

    All vehicles 

  22. G15304210Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Remove the 3 bolts.
    • Remove the idler pulley bracket.
  23. G15322222Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Remove the bolt.
    • Release the ground cable and position to one side.
  24. G15322223Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Remove the engine mount nut.

  25. CAUTION: Use a wooden block to protect the oil pan when supporting the engine.
    G15322224Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Support the engine.

    General Equipment: Transmission jack 

  26. G15322226Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Remove the 4 engine mount bracket bolts.
    • Reposition the engine mount bracket.
  27. G15304215Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Remove the engine mount bracket.

  28. G15304216Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Disconnect the 2 electrical connectors.
    • Release the 4 wiring harness clips as illustrated.
    • Position the wiring harness to one side.
  29. G15304217Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Remove the 2 bolts.
    • Remove the HP  fuel line cover.
  30. WARNING: Be prepared to collect escaping fuel.
    CAUTION:
    • Before disconnecting any components, make sure the area is clean and free from foreign material. When disconnected all openings must be sealed.
    • Remove and discard the HP  fuel supply lines.
    G15304218Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Disconnect the 2 HP  fuel line unions.
    • Remove the 2 HP  fuel line bracket bolts.
    • Remove and discard the HP  fuel line assembly.
  31. WARNING: Be prepared to collect escaping fuel.
    CAUTION: Before disconnecting any components, make sure the area is clean and free from foreign material. When disconnected all openings must be sealed.
    G15304278Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Remove the Low Pressure (LP) fuel line bracket bolt.
    • Disconnect the 2 LP  fuel line unions.
  32. G15304279Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Remove the HP  fuel pump cover.

  33. WARNING: Be prepared to collect escaping fuel.
    CAUTION: Before disconnecting any components, make sure the area is clean and free from foreign material. When disconnected all openings must be sealed.
    NOTE: Loosen the bolts a turn each at a time.
    G15304280Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Remove the 2 HP  fuel pump bolts.
    • Remove the HP  fuel pump.
  34. CAUTION: Be prepared to collect escaping fluids.
    G15304281Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Remove the HP  fuel pump tappet.

scientia non olet · About LEMON Manuals