LEMON Manuals: Even more car manuals for everyone
Home >> Land Rover >> 2021 >> Range Rover Velar R-Dynamic HSE >> Repair and Diagnosis >> External Pages >> Different car >> Section 6 (Fuel Charging And Controls - V8 S/C 5.0L Petrol -- Range Rover Velar/L560) >> Fuel Charging And Controls - V8 S/C 5.0L Petrol >> Removal And Installation >> Fuel Injectors (G2244109) >> Removal

Fuel Injectors (G2244109): Removal

WARNING: This page is about a different car, the 2020 Land Rover Range Rover Velar. However, it is still accessible from the selected car via links, so may be relevant.
CAUTION:
  • Before disconnecting any components, make sure the area is clean and free from foreign material. When disconnected all openings must be sealed.
  • Protect the surrounding paintwork to avoid damage.
  • Make sure that the tools and equipment are clean, free of foreign material and lubricant.
NOTE:
  • This procedure contains some variation in the illustrations depending on the vehicle specification, but the essential information is always correct.
  • This procedure contains illustrations showing certain components removed to provide extra clarity.
  1. Always follow the fuel system health and safety precautions when doing any repairs to the fuel system.

    Refer to: PETROL AND PETROL-ETHANOL FUEL SYSTEMS HEALTH AND SAFETY PRECAUTIONS .

  2. Release the pressure in the fuel system.

    Refer to: FUEL SYSTEM PRESSURE RELEASE .

  3. Disconnect the startup battery ground cable.

    Refer to: STARTUP BATTERY DISCONNECT AND CONNECT .

  4. Drain the coolant.

    Refer to: COOLING SYSTEM PARTIAL DRAINING AND VACUUM FILLING .

  5. CAUTION: Be prepared to collect escaping fluids.
    G14286625Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Disconnect the 2 right side coolant pipes.
    • Release the clip.
  6. G14287374Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Remove the oil filler cap.
    • Remove the Noise, Vibration and Harshness (NVH) material.
    • Install the engine oil filler cap.
  7. G14287856Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Disconnect the vacuum pipe connector.

  8. CAUTION: Be prepared to collect escaping fluids.
    G14287857Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Disconnect the 2 left side coolant pipes.

  9. G11713385Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Remove the NVH material.

  10. Remove the air filter outlet pipe T-connector.

    Refer to: AIR FILTER OUTLET PIPE T-CONNECTOR .

  11. G14287859Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Disconnect the breather pipe.

  12. CAUTION:
    • Be prepared to collect escaping fluids.
    • Make sure that all openings are sealed. Use new blanking caps.
    G14287860Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Remove the 4 bolts.
    • Remove the 2 fuel line unions.
    • Remove and discard the fuel line.
  13. G11607603Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Release the wiring harness clip.

  14. CAUTION:
    • Be prepared to collect escaping fluids.
    • Make sure that all openings are sealed. Use new blanking caps.
    G11607604Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Disconnect the fuel line union.
    • Remove the nut.
  15. WARNING: Do not work on or under a vehicle supported only by a jack. Always support the vehicle on safety stands.

    Raise and support the vehicle.

  16. Remove the engine undershield.

    Refer to: ENGINE UNDERSHIELD .

  17. NOTE: Engine shown removed for clarity.
    G11607621Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Carefully release the 2 clips.
    • Disconnect the 2 electrical connectors.
  18. NOTE: Engine shown removed for clarity.
    G11686730Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Remove the 2 bolts and the heatshield.
  19. G14287865Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Release the accessory drive belt.

  20. G11606720Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Remove the 3 bolts.
    • Remove the idler pulley assembly.
  21. Remove the generator.

    Refer to: GENERATOR .

  22. CAUTION:
    • Be prepared to collect escaping fluids.
    • Make sure that all openings are sealed. Use new blanking caps.
    NOTE: Engine shown removed for clarity.
    G11607688Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Release the fuel line unions.
    • Remove the 2 bolts.
    • Remove and discard the fuel line assembly.
  23. Lower the vehicle.
  24. G14287868Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Disconnect the electrical connector.

  25. G11688955Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Disconnect the 4 fuel injector electrical connectors.
    • Disconnect the 4 ignition coil electrical connector.
    • Position the wiring harness to one side.
    • Repeat process to the other side.
  26. G11688956Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Remove both side ignition coils.

  27. CAUTION:
    • Make a note of the fuel injector clamp alignment to the fuel rail prior to removal.
    • Make sure that the fuel injectors and the belonging fuel injector clamps are marked up prior to removal, if existing fuel injectors are to be re-used each fuel injector has to be installed with the original clamp to its original location.
    G11688958Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Remove both side fuel rails.

  28. CAUTION:
    • Make sure that the special tool is located correctly to the fuel injector prior to removing the fuel injector.
    • Make sure that the special tool is held square to the fuel injector during removal.
    • Make sure that all open ports are covered to prevent any foreign material ingress.
    G11607550Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Using the special tool, remove the 8 fuel injectors.

    Special Tool(s): 310-197 

  29. CAUTION: If the fuel injector is being removed without a new component being installed, the fuel injector clamp must remain with the fuel injector it is removed with.
    G11587674Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Remove and discard the 8 fuel injector retaining clamps.

  30. CAUTION:
    • Do not use a knife to remove the Teflon™ seal as damage could occur to the fuel injector.
    • Do not cut the Teflon™ seal too deep as damage could occur to the fuel injector.
    • Pinch the Teflon™ seal to allow the tool to cut the Teflon™ seal without damaging the fuel injector.
    G11607552Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Remove and discard the 8 Teflon™ seals.

  31. CAUTION: Do not use any sharp tools to remove the O-ring seal as damage could occur to the fuel injector.
    G11607553Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Remove and discard the 8 O-ring seals.
scientia non olet · About LEMON Manuals