LEMON Manuals: Even more car manuals for everyone
Home >> Land Rover >> 2021 >> Range Rover Velar R-Dynamic HSE >> Repair and Diagnosis >> Accessories & Equipment >> Gauges & Instrument Panels >> Instrument Panel And Console -- Range Rover Velar/L560 >> Instrument Panel And Console (G2523307) >> Removal And Installation >> In-Vehicle Crossbeam (G2018929) >> Installation

In-Vehicle Crossbeam (G2018929): Installation

The following step(s) applies to: 

All vehicles 

    • Install the in-vehicle crossbeam onto the climate control assembly.
    • Tighten the 7 bolts.

      Torque  : 10 Nm 

  2. CAUTION: Take extra care not to damage the wiring harnesses.
    • With assistance, install the in-vehicle crossbeam.
    • Tighten the 4 bolts.

      Torque  : 20 Nm 

    • Install the bracket.
    • Tighten the 3 bolts.

      Torque  : 10 Nm 

    • Connect the wiring harness.
  4. NOTE: Repeat the step for the other side.

    Connect the 2 drain tubes.

  5. Connect the wiring harness on the passenger side at 5 clips.
    • Connect the 4 electrical connectors to the climate module.
    • Connect the 2 electrical connectors.
    • Connect the wiring harness.
  7. Connect the 2 electrical connectors to the Body Control Module/Gateway Module Assembly (BCM/GWM).
  8. Connect the 4 electrical connectors.
    • Install the cover.
    • Connect the wiring harness.
    • Connect the wiring harness.
    • Install the ground cable bolt.
  11. Install the glovebox cooling duct.
  12. Connect the wiring harness.
  13. Connect the climate sensor electrical connector on the passenger side.
    • Connect the electrical connector to the electric booster heater.
    • Connect the wiring harness.
    • Connect the climate sensor electrical connector on the driver side.
    • Connect the wiring harness.
    • Position the instrument panel wiring harness at driver side 'A' Pillar.
    • Connect the electrical connector.
    • Tighten the torx screw.
  17. NOTE: Repeat the step for the other side.

    Install the cross car beam lower bracket.

    • Install the floor heater duct on the driver side.
    • Connect the climate sensor electrical connector on the driver side.
    • Tighten the screw.
    • Install the clip.
  19. Install the driver floor mat.
    • Install the floor heater duct on the passenger side.
    • Connect the climate sensor electrical connector on the passenger side.
    • Tighten the screw.
    • Install the clip.
  21. Install the passenger floor mat.
  22. CAUTION: Passengers side only.
    • Install the cowl side trim panel.
    • Tighten the screw.
    • Position the door weatherstrip.
  23. CAUTION: Drivers side only.
    • Install the cowl side trim panel.
    • Tighten the screw.
    • Position the door weatherstrip.
  24. CAUTION: Drivers side only.
    • Install the hood release lever.
    • Tighten the screw.
  25. NOTE: Repeat the step for the other side.
    • Connect the electrical connector.
    • Install the front treadplate trim panel.

    The following step(s) applies to: 

    Right-hand drive vehicles 

  26. CAUTION: Make sure that the surface is clean and free of foreign material.
    • Connect the Air Conditioning (A/C) pipes.
    • Tighten the bolt.

      Torque  : 9 Nm 

    • Tighten the nut.

      Torque  : 20 Nm 

    • Connect the 2 coolant hoses.
    • Connect the coolant hose and secure with the clip.
    • Install and tighten the torx bolt.

      Torque  : 20 Nm 

    The following step(s) applies to: 

    Left-hand drive vehicles 

  28. CAUTION: Make sure that the surface is clean and free of foreign material.
    • Connect the Air Conditioning (A/C) pipes.
    • Tighten the bolt.

      Torque  : 9 Nm 

    • Install and tighten the torx bolt.

      Torque  : 20 Nm 

    • Connect the 2 coolant hoses.
    • Connect the coolant hose and secure with the clip.
    • Install and tighten the nut.

      Torque  : 20 Nm 

  30. Install the secondary bulkhead right panel.

    Refer to: SECONDARY BULKHEAD RIGHT INNER PANEL - INGENIUM I6 3.0L PETROL .

    Refer to: SECONDARY BULKHEAD RIGHT INNER PANEL - INGENIUM I4 2.0L PETROL .

    The following step(s) applies to: 

    All vehicles 

  31. Install the secondary bulkhead left panel.

    Refer to: SECONDARY BULKHEAD LEFT INNER PANEL - INGENIUM I6 3.0L PETROL (G2743717) .

    Refer to: SECONDARY BULKHEAD LEFT INNER PANEL - INGENIUM I4 2.0L PETROL .

  32. Install the instrument panel console.

    Refer to: INSTRUMENT PANEL CONSOLE .

  33. Install the steering column.

    Refer to: STEERING COLUMN AND STEERING WHEEL - VEHICLES WITH: MANUAL ADJUSTMENT (G2523168) .

  34. NOTE: Repeat the procedure for the other side.

    Install the front seats.

    Refer to: FRONT ROW SEAT - VEHICLES WITH: POWER SEATS .

    Refer to: FRONT ROW SEAT - VEHICLES WITHOUT: POWER SEATS .

  35. Charge the air conditioning (A/C) system.

    Refer to: AIR CONDITIONING SYSTEM RECOVERY, EVACUATION AND CHARGING .

  36. Fill and bleed the cooling system.

    Refer to: COOLING SYSTEM PARTIAL DRAINING AND VACUUM FILLING - INGENIUM I6 3.0L PETROL .

    Refer to: COOLING SYSTEM PARTIAL DRAINING AND VACUUM FILLING - INGENIUM I4 2.0L PETROL/INGENIUM I4 2.0L PETROL - PHEV .

  37. Connect the startup battery ground cable.

    Refer to: STARTUP BATTERY DISCONNECT AND CONNECT .

scientia non olet · About LEMON Manuals