LEMON Manuals: Even more car manuals for everyone
Home >> Land Rover >> 2021 >> Range Rover Evoque R-Dynamic S >> Repair and Diagnosis >> Brakes >> Mechanical - Hydraulic >> Rear Disc Brake -- Range Rover EVOQUE/L551 >> Rear Disc Brake >> Removal And Installation >> Brake Pads - Vehicles With: PHEV (G2740581) >> Installation

Brake Pads - Vehicles With: PHEV (G2740581): Installation

  1. WARNING: Do not use compressed air to clean brake components. Dust from friction materials can be harmful if inhaled.
    G14428216Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Use brake cleaner fluid to clean the brake caliper and brake caliper carrier.

    Material: Brake Cleaner () 

  2. CAUTION: Damaged components must be replaced.
    G14428217Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Inspect the caliper piston and slide pin seals for damage.

  3. G14428200Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Release the 7 fasteners.
    • Remove the access cover.
    • Remove the brake fluid reservoir cap, and check the brake fluid level.
    • Use a syringe to remove the excessive brake fluid to avoid the brake fluid reservoir to overflow.
  4. G14428239Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Use the special tool to fully retract the brake caliper piston.

    Special Tool(s): 206-080 

  5. NOTE: Make sure that the anti-rattle spring is installed to the noted position prior to removal.
    G14428220Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Install the anti-rattle spring.
    • Install the brake pads.
  6. G14428219Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Install the brake caliper.
    • Install and tighten the 2 guide pins to the brake caliper and install the 2 dust caps.

      Torque  : 30 Nm 

    • Connect the electrical connector to the EPB  .
    • Secure the wiring harness to the bracket.
    • Install the anti-rattle spring.
  7. Repeat the above procedure for the other side.
  8. NOTE:
    • Right side only.
    • If new brake pads are installed make sure that a new brake pad wear sensor is installed.
    G14428211Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Connect the brake pad wear sensor to the brake pad.

      Renew Part: Brake pad wear sensor cable Quantity: 1 . 

    • Secure the 2 brake pad wear sensor wiring harness grommets to the brackets.
  9. CAUTION: Failure to follow this instruction may lead to brake warning lamps and Diagnostic Trouble Code(s) (DTC) being set.
    G14428203Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    1. NOTE: Although the brake pedal might feel firm make sure to hold the pedal through the 10 second period.

      If the Integrated Power Brake unit - 'Assembly Mode' has not been activated, press and hold the brake pedal in a single apply for 10 seconds.

    2. If the brake pedal felt soft and fell to the floor proceed to substep  4.
    3. If the brake pedal felt firm proceed to substep  5.
    4. NOTE: Make sure to repeatedly press the brake pedal until a firm brake pedal is reached.

      If the Integrated Power Brake unit - 'Assembly Mode' has been activated, press the brake pedal several times until a firm brake pedal is reached.

    5. Check the fluid level in the brake fluid reservoir and top-up with brake fluid if necessary.
  10. G14428200Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Check and clean the area around the brake fluid reservoir cap, if necessary.
    • Install the access.
    • Secure the 7 fasteners.
  11. Install the rear wheels and tires.

    Refer to: WHEEL AND TIRE .

  12. Use the JLR  approved diagnostic equipment to deactivate the Integrated Power Brake Assembly mode.

    General Equipment: Jaguar Land Rover approved diagnostic equipment 

  13. Remove the EPB  from maintenance position.

    General Equipment: Jaguar Land Rover approved diagnostic equipment 

scientia non olet · About LEMON Manuals