LEMON Manuals: Even more car manuals for everyone
Home >> Land Rover >> 2021 >> Defender 110 >> Repair and Diagnosis >> Engine Mechanical >> Mechanical >> Engine - INGENIUM 2.0L Petrol/INGENIUM I4 2.0L Petrol - PHEV -- Defender/L663 (1 Of 2) >> Engine - INGENIUM I4 2.0L Petrol/INGENIUM I4 2.0L Petrol - PHEV (G2344339) >> Removal And Installation >> Cylinder Head (G2344454) >> Installation

Cylinder Head (G2344454): Installation

  1. Check the cylinder head face for distortion.

    Refer to: CYLINDER HEAD DISTORTION MEASUREMENT - INGENIUM I4 2.0L PETROL

  2. CAUTION: Make sure that the dowels and dowel holes are clean and free from debris and foreign material.

    Install the 2 dowels.

  3. CAUTION:
    • Make sure that the mating surfaces are clean and free from debris and foreign material.
    • The cylinder head gasket must be installed over the cylinder head to the 2 dowels
    G11717709Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Install a new cylinder head gasket.

    Renew Part: Cylinder head gasket Quantity: 1  .

  4. CAUTION: Make sure that the component is correctly located on the locating dowels.

    With the aid of another technician, install the cylinder head.

  5. G11717712Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Use the special tool to install and tighten 10 new cylinder head bolts in the illustrated sequence.

      Special Tool(s): JLR-303-1653 

      Renew Part: Cylinder head bolts Quantity: 10  .

      Torque  : 20 Nm 

  6. G11717712Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Use the special tool to tighten the 10 bolts in the illustrated sequence.

      Special Tool(s): JLR-303-1653 

      Torque 

      Stage 1: 90° 

      Stage 2: 180° 

    • Remove the special tool.

      Special Tool(s): JLR-303-1653 

  7. G11717715Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Install and tighten the bolt.

    Torque  : 25 Nm 

  8. G11717705Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Install and tighten the 3 bolts.

    Torque  : 12 Nm 

  9. CAUTION:
    • Make sure that the components are clean, dry and free from corrosion and foreign material.
    • Inspect the components for wear and replace if necessary.
    NOTE: Make sure that these components are installed to the noted removal position.
    • Install the 8 hydraulic lash adjusters.
    • Install the 8 camshaft followers.
  10. Install the front Noise, Vibration and Harshness (NVH) material.
  11. Install the left NVH material.
    • Connect the coolant pipe to the cylinder head.
    • Install and tighten the bolt.

      Torque  : 8 Nm 

  13. G15319342Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Install 5 new O-ring seals.

      Renew Part: Oil filter housing inlet/outlet O-ring seals Quantity: 1  .

      Renew Part: Oil filter housing drain port O-ring seal Quantity: 1  .

    • Install the 2 pipes to the oil filter housing.
    • Install the oil filter housing.
    • Install and tighten the 3 bolts.

      Torque  : 12 Nm 

    • Install the coolant pipe assembly.
    • Install and tighten the 2 bolts.

      Torque  : 12 Nm 

  16. Install and tighten a new cylinder head temperature sensor.

    Renew Part: Cylinder head temperature sensor Quantity: 1  .

    Torque  : 11 Nm 

    • Connect the electrical connector to the oil pressure and temperature sensor.
    • Connect the electrical connector to the cylinder head temperature sensor.
    • Connect the electrical connector to the link harness.
    • Install and tighten the bolt.

      Torque  : 7 Nm 

  18. Install the camshaft carrier.

    Refer to: CAMSHAFT CARRIER 

  19. Install the turbocharger.

    Refer to: TURBOCHARGER - INGENIUM I4 2.0L PETROL

  20. Install the intake manifold.

    Refer to: INTAKE MANIFOLD - INGENIUM I4 2.0L PETROL 

  21. Install a new oil filter element.

    Refer to: OIL FILTER ELEMENT 

  22. Connect the startup battery ground cable.

    Refer to: 12V SYSTEM DISCONNECT AND CONNECT

scientia non olet · About LEMON Manuals