Transfer Case Control Module DTC Action Table

TRANSFER CASE CONTROL MODULE DTC ACTION

DTC CODE	PERMANENT DTC ACTION	INTERMITTENT DTC ACTION
P0605-43 P062F-43 P062F-68 P0666-11 P0666-12 P0666-29 P0666-64 P160C-45 P160C-48 P160C-94 U200C-9A	Install a new transfer case control module and configure as a new module. Refer to the Transfer Case Control Module Replacement Application instructions in this article	Using Jaguar Land Rover approved diagnostic equipment, perform the Transfer Case Healthcheck Application. The application will subsequently test the system and report a DTC if a fault persists If fault persists, install a new transfer case control module and configure as a new module. Refer to the Transfer Case Control Module Replacement Application instructions in this article
P18A4-13 P18A4-16 P18A4-17	Refer to the electrical circuit diagrams and check the hi/low range position sensor power circuit for circuit faults. Repair circuit as required, clear DTC and retest If the fault persists, install and configure a new high/low range position sensor. Refer to the High/Low Range Position Sensor Replacement Application instructions in this article Clear DTC , start the engine and retest If fault persists, install a new transfer case control module and configure as a new module. Refer to the Transfer Case Control Module Replacement Application instructions in this article	Clear DTC , start the engine and retest
P18A5-03 P18A5-11 P18A5-12 P18A5-13 P18A5-37	Refer to the electrical circuit diagrams and check the hi/low range position sensor signal circuit for circuit faults. Repair circuit as required, clear DTC and retest If the fault persists, install and configure a new high/low range position sensor. Refer to the High/Low Range Position Sensor Replacement Application instructions in this article Clear DTC , start the engine and retest If fault persists, install a new transfer case control module and configure as a new module. Refer to the Transfer Case Control Module Replacement Application instructions in this article	Clear DTC , start the engine and retest
U0080-88	Refer to the electrical circuit diagrams and check the FlexRay bus circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair circuit as required Clear DTC , start the engine and retest If fault persists, install a new transfer case control module and configure as a new module. Refer to the Transfer Case Control Module Replacement Application instructions in this article	Using Jaguar Land Rover approved diagnostic equipment, perform the Transfer Case Healthcheck Application. The application will subsequently test the system and report a DTC if a fault persists If fault persists, install a new transfer case control module and configure as a new module. Refer to the Transfer Case Control Module Replacement Application instructions in this article
U1000-02 U1000-11 U1000-12 U1000-16 U1000-17 U1000-1C U1000-49 U1000-56 U1000-62 U1A4B-16 U1A4B-17 U1A4B-1C U1A4B-47 U1A4B-48 U1A4B-49 U1A4B-55 U1A4B-56 U1A4B-64 U1A4B-84 U200C-4B U200C-64 U2011-18 U2011-19 U2011-1D U2011-28 U2011-41 U2011-56 U2011-62 U2011-68 U2011-77 U2011-78 U2011-85 U2011-86 U2011-9A U2016-04 U2016-06 U2016-47 U2016-49 U2016-92 U3000-1C U3000-42 U3000-4A U3012-04 U3012-1C U3012-48 U3012-92 U3012-94 U3012-96	Install a new transfer case control module and configure as a new module. Refer to the Transfer Case Control Module Replacement Application instructions in this article	Using Jaguar Land Rover approved diagnostic equipment, perform the Transfer Case Healthcheck Application. The application will subsequently test the system and report a DTC if a fault persists If fault persists, install a new transfer case control module and configure as a new module. Refer to the Transfer Case Control Module Replacement Application instructions in this article
U3006-13	Refer to the electrical circuit diagrams and check the transfer case control module power and ground circuits for open circuit, high resistance. Repair circuit as required, clear DTC and retest Using Jaguar Land Rover approved diagnostic equipment, check for related low voltage DTC s and refer to the relevant DTC index Using Jaguar Land Rover approved diagnostic equipment, perform the Transfer Case Healthcheck Application. The application will subsequently test the system and report a DTC if a fault persists	Using Jaguar Land Rover approved diagnostic equipment, perform the Transfer Case Healthcheck Application. The application will subsequently test the system and report a DTC if a fault persists If fault persists, install a new transfer case control module and configure as a new module. Refer to the Transfer Case Control Module Replacement Application instructions in this article