Battery And Charging System - General Information (G1568866): Specifications
BATTERY SPECIFICATION
| ENGINE VARIANTS | ITEM | SPECIFICATIONS |
|---|---|---|
| Primary battery | Type | Absorbed glass mat (AGM) |
| Capacity | 90 Ah | |
| Cold cranking amps | 850 CCA | |
| Reserve capacity | 150 minutes | |
| Secondary battery - vehicles with 3.0 TdV6 (cold markets only) and vehicles with 4.4L TdV8 | Type | Absorbed glass mat (AGM) |
| Capacity | 70 Ah | |
| Cold cranking amps | 760 CCA | |
| Reserve capacity | 120 minutes | |
| Secondary battery - vehicles with Stop/Start system | Type | Absorbed glass mat (AGM) |
| Capacity | 14 Ah | |
| Cold cranking amps | 200 CCA |
Primary battery disconnect/connect
CAUTION:
- The vehicle status and battery condition must be established before attempting battery disconnect/connect. Reference must then be made to the following table to establish the relevant procedure to be followed.
- After connecting the battery, the steering wheel must be turned to full left-hand and full right-hand lock with the engine running. This allows the dynamic stability control system to calibrate the steering wheel position. Failure to follow this instruction will result in a variety of instrument cluster warning lights being illuminated.
NOTE:
- For 2018 Model Year onward PHEV vehicles Refer to: 12V SYSTEM DISCONNECT (G2224436)
- If there is insufficient capacity in the battery to disarm the alarm, the alarm may sound on connection of the battery - turning the ignition key to position II will disarm the alarm.
- If a new battery is installed, the battery monitoring system (BMS) must be reset using Land Rover approved diagnostic equipment.
| Vehicle status | Battery charged | Battery discharged |
|---|---|---|
| - | Procedure | Procedure |
| Vehicles without Telematics | - | - |
| Engine running | 1 | - |
| Vehicle powered down, locked and alarmed | 2 | 3 |
| Vehicle unlocked | 4 | 5 |
| Vehicles with Telematics | - | - |
| Engine running | 6 | - |
| Vehicle powered down, locked and alarmed | 7 | 8 |
| Vehicle unlocked | 9 | 10 |
BATTERY DIAGNOSTIC PROCEDURE 1
| Disconnect the battery | Connect the battery |
|---|---|
| 1. If possible, apply the parking brake or chock the wheels | 1. Make sure that all the electrical systems and ignition are switched OFF |
| 2. Set the ignition to the OFF position. | 2. Connect the battery GROUND cable |
| 3. Wait 2 minutes for the engine management system to POWER DOWN | 3. Reset electric window one-touch facility. Power window up to hard stop, release switch, reapply and hold for 1 second (relay in door will click). One touch should now work |
| 4. Remove the spare wheel | 4. Using suitable Land Rover diagnostic equipment calibrate the electric park brake, both tailgates. Check the clock and navigation settings. |
| 5. Disconnect the battery GROUND cable | - |
BATTERY DIAGNOSTIC PROCEDURE 2
| Disconnect the battery | Connect the battery |
|---|---|
| 1. Unlock the vehicle and disarm the alarm using the UNLOCK button on the key fob | 1. Make sure that all the electrical systems and ignition are switched OFF |
| 2. Enter the vehicle, set the ignition to the ON position, apply the parking brake or chock the wheels and then set the ignition to the OFF position. | 2. Connect the battery GROUND cable |
| 3. Wait 2 minutes for the engine management system to POWER DOWN | 3. Reset electric window one-touch facility. Power window up to hard stop, release switch, reapply and hold for 1 second (relay in door will click). One touch should now work |
| 4. Remove the spare wheel | 4. Using suitable Land Rover diagnostic equipment calibrate the electric park brake, both tailgates. Check the clock and navigation settings. |
| 5. Disconnect the battery GROUND cable | - |
BATTERY DIAGNOSTIC PROCEDURE 3
| Disconnect the battery | Connect the battery |
|---|---|
| 1. Unlock the vehicle from the driver's door using the key | 1. Make sure that all the electrical systems and ignition are switched OFF |
| 2. Enter the vehicle, apply the parking brake or chock the wheels | 2. Connect the battery GROUND cable |
| 3. Remove the spare wheel | 3. Set the ignition to the ON position. |
| 4. Disconnect the battery GROUND cable | 4. Reset electric window one-touch facility. Power window up to hard stop, release switch, reapply and hold for 1 second (relay in door will click). One touch should now work |
| - | 5. Using suitable Land Rover diagnostic equipment calibrate the electric park brake, both tailgates. Check the clock and navigation settings. |
BATTERY DIAGNOSTIC PROCEDURE 4
| Disconnect the battery | Connect the battery |
|---|---|
| 1. Enter the vehicle, set the ignition to the ON position, apply the parking brake or chock the wheels and then set the ignition to the OFF position. | 1. Make sure that all the electrical systems and ignition are switched OFF |
| 2. Wait 2 minutes for the engine management system to POWER DOWN | 2. Connect the battery GROUND cable |
| 3. Remove the spare wheel | 3. Reset electric window one-touch facility. Power window up to hard stop, release switch, reapply and hold for 1 second (relay in door will click). One touch should now work |
| 4. Disconnect the battery GROUND cable | 4. Using suitable Land Rover diagnostic equipment calibrate the electric park brake, both tailgates. Check the clock and navigation settings. |
BATTERY DIAGNOSTIC PROCEDURE 5
| Disconnect the battery | Connect the battery |
|---|---|
| 1. Enter the vehicle, apply the parking brake or chock the wheels | 1. Make sure that all the electrical systems and ignition are switched OFF |
| 2. Remove the spare wheel | 2. Connect the battery GROUND cable |
| 3. Disconnect the battery GROUND cable | 3. Set the ignition to the ON position. |
| - | 4. Reset electric window one-touch facility. Power window up to hard stop, release switch, reapply and hold for 1 second (relay in door will click). One touch should now work |
| - | 5. Using suitable Land Rover diagnostic equipment calibrate the electric park brake, both tailgates. Check the clock and navigation settings. |
BATTERY DIAGNOSTIC PROCEDURE 6
| Disconnect the battery | Connect the battery |
|---|---|
| 1. Make sure the customer has placed stolen vehicle tracking into Service Mode (if equipped). | 1. Make sure that all the electrical systems and ignition are switched OFF |
| 2. If possible, apply the parking brake or chock the wheels | 2. Connect the battery GROUND cable |
| 3. Set the ignition to the OFF position. | 3. Reset electric window one-touch facility. Power window up to hard stop, release switch, reapply and hold for 1 second (relay in door will click). One touch should now work |
| 4. Wait 2 minutes for the engine management system to POWER DOWN | 4. Using suitable Land Rover diagnostic equipment calibrate the electric park brake, both tailgates. Check the clock and navigation settings. |
| 5. Remove the spare wheel | 5. Request stolen vehicle tracking removed from Service Mode (if equipped). |
| 6. Disconnect the battery GROUND cable | - |
BATTERY DIAGNOSTIC PROCEDURE 7
| Disconnect the battery | Connect the battery |
|---|---|
| 1. Make sure the customer has placed stolen vehicle tracking into Service Mode (if equipped). | 1. Make sure that all the electrical systems and ignition are switched OFF |
| 2. Unlock the vehicle and disarm the alarm using the UNLOCK button on the key fob | 2. Connect the battery GROUND cable |
| 3. Enter the vehicle, set the ignition to the ON position, apply the parking brake or chock the wheels and then set the ignition to the OFF position. | 3. Reset electric window one-touch facility. Power window up to hard stop, release switch, reapply and hold for 1 second (relay in door will click). One touch should now work |
| 4. Wait 2 minutes for the engine management system to POWER DOWN | 4. Using suitable Land Rover diagnostic equipment calibrate the electric park brake, both tailgates. Check the clock and navigation settings. |
| 5. Remove the spare wheel | 5. Request stolen vehicle tracking removed from Service Mode (if equipped). |
| 6. Disconnect the battery GROUND cable | - |
CAUTION:
Battery discharge may have activated the stolen vehicle tracking, check with customer if equipped.
BATTERY DIAGNOSTIC PROCEDURE 8
| Disconnect the battery | Connect the battery |
|---|---|
| 1. Make sure the customer has placed stolen vehicle tracking into Service Mode (if equipped). | 1. Make sure that all the electrical systems and ignition are switched OFF |
| 2. Unlock the vehicle from the driver's door using the key | 2. Connect the battery GROUND cable |
| 3. Enter the vehicle, apply the parking brake or chock the wheels | 3. Set the ignition to the ON position. |
| 4. Remove the spare wheel | 4. Reset electric window one-touch facility. Power window up to hard stop, release switch, reapply and hold for 1 second (relay in door will click). One touch should now work |
| 5. Disconnect the battery GROUND cable | 5. Using suitable Land Rover diagnostic equipment calibrate the electric park brake, both tailgates. Check the clock and navigation settings. |
| - | 5. Request stolen vehicle tracking removed from Service Mode (if equipped). |
BATTERY DIAGNOSTIC PROCEDURE 9
| Disconnect the battery | Connect the battery |
|---|---|
| 1. Make sure the customer has placed stolen vehicle tracking into Service Mode (if equipped). | 1. Make sure that all the electrical systems and ignition are switched OFF |
| 2. Enter the vehicle, set the ignition to the ON position, apply the parking brake or chock the wheels and then set the ignition to the OFF position. | 2. Connect the battery GROUND cable |
| 3. Wait 2 minutes for the engine management system to POWER DOWN | 3. Reset electric window one-touch facility. Power window up to hard stop, release switch, reapply and hold for 1 second (relay in door will click). One touch should now work |
| 4. Remove the spare wheel | 4. Using suitable Land Rover diagnostic equipment calibrate the electric park brake, both tailgates. Check the clock and navigation settings. |
| 5. Disconnect the battery GROUND cable | 5. Request stolen vehicle tracking removed from Service Mode (if equipped). |
CAUTION:
Battery discharge may have activated the stolen vehicle tracking, check with customer if equipped.
BATTERY DIAGNOSTIC PROCEDURE 10
| Disconnect the battery | Connect the battery |
|---|---|
| 1. Make sure the customer has placed stolen vehicle tracking into Service Mode (if equipped). | 1. Make sure that all the electrical systems and ignition are switched OFF |
| 2. Enter the vehicle, apply the parking brake or chock the wheels | 2. Connect the battery GROUND cable |
| 3. Remove the spare wheel | 3. Set the ignition to the ON position. |
| 4. Disconnect the battery GROUND cable | 4. Reset electric window one-touch facility. Power window up to hard stop, release switch, reapply and hold for 1 second (relay in door will click). One touch should now work |
| - | 5. Using suitable Land Rover diagnostic equipment calibrate the electric park brake, both tailgates. Check the clock and navigation settings. |
| - | 6. Request stolen vehicle tracking removed from Service Mode (if equipped). |
SECONDARY BATTERY DISCONNECT AND CONNECT
| Vehicle status | Procedure |
|---|---|
| Vehicles without Telematics | 1 |
| Vehicles with Telematics | 2 |
BATTERY DIAGNOSTIC PROCEDURE 1
| Disconnect the battery | Connect the battery |
|---|---|
| 1. Enter the vehicle, apply the parking brake or chock the wheels | 1. Make sure that all the electrical systems and ignition are switched OFF |
| 2. Remove the luggage compartment side trim | 2. Connect the battery GROUND cable |
| 3. Wait 2 minutes for the engine management system to POWER DOWN | 3. Set the ignition to the ON position. |
| 4. Disconnect the battery GROUND cable | 4. Reset electric window one-touch facility. Power window up to hard stop, release switch, reapply and hold for 1 second (relay in door will click). One touch should now work |
| - | 5. Using suitable Land Rover diagnostic equipment calibrate the electric park brake, both tailgates. Check the clock and navigation settings. |
BATTERY DIAGNOSTIC PROCEDURE 2
| Disconnect the battery | Connect the battery |
|---|---|
| 1. Make sure the customer has placed stolen vehicle tracking into Service Mode (if equipped). | 1. Make sure that all the electrical systems and ignition are switched OFF |
| 2. Enter the vehicle, apply the parking brake or chock the wheels | 2. Connect the battery GROUND cable |
| 3. Remove the luggage compartment side trim | 3. Set the ignition to the ON position. |
| 4. Wait 2 minutes for the engine management system to POWER DOWN | 4. Reset electric window one-touch facility. Power window up to hard stop, release switch, reapply and hold for 1 second (relay in door will click). One touch should now work |
| 5. Disconnect the battery GROUND cable | 5. Using suitable Land Rover diagnostic equipment calibrate the electric park brake, both tailgates. Check the clock and navigation settings. |
| - | 6. Request stolen vehicle tracking removed from Service Mode (if equipped). |
Vehicle Jump (Emergency) Starting - Using Another Vehicle
WARNING:
- Take care when working near rotating parts of the engine.
- Prior to attempting to start the disabled vehicle, make sure that the parking brake is applied or suitably chock the wheels. Make sure that 'P' - PARK - Automatic Gearbox or NEUTRAL - Manual Gearbox is selected.
- Suitable eye protection must be worn when working in the vicinity of the battery.
- DO NOT attempt to start the disabled vehicle if it is suspected that the electrolyte in the battery is frozen.
- During normal use, batteries emit explosive hydrogen gas sufficient to cause severe explosions and capable of causing serious injury - keep sparks and naked lights away from the engine compartment.
CAUTION:
- Make sure that there is no physical contact between the donor and disabled vehicles other than the booster cables.
- Make sure that the slave battery/starting aid is of the 12 volt type.
- Make sure that all electrical systems and ignition are switched OFF prior to connecting the booster cables.
- Disconnect the booster cables prior to operating any electrical systems.
| Vehicle status | Procedure |
|---|---|
| Vehicles without Telematics | 1 |
| Vehicles with Telematics | 2 |
CARRY OUT OPERATIONS IN SEQUENCE - PROCEDURE 1
| Carry out the following operations in the sequence given |
|---|
| 1. Connect one end of the RED (+) booster cable to the POSITIVE (+) battery terminal of the DONOR vehicle |
| 2. Connect the other end of the RED (+) booster cable to the POSITIVE (+) battery terminal of the DISABLED vehicle |
| 3. Connect one end of the BLACK (-) booster cable to the GROUND (-) battery terminal of the DONOR vehicle |
| 4. Connect the other end of the BLACK (-) booster cable to a good earth point (e.g. unpainted metal surface or engine mounting) at least 0.5 m from the battery or fuel lines on the DISABLED vehicle |
| 5. Start the engine of the DONOR vehicle and allow it to idle for a few minutes |
| 6. Start the engine of the DISABLED vehicle |
| 7. Allow the engines of both vehicles to idle for a few minutes, then switch off the engine of the DONOR vehicle |
| 8. Disconnect the BLACK (-) booster cable from the earth point of the PREVIOUSLY DISABLED vehicle |
| 9. Disconnect the BLACK (-) booster cable from the battery of the DONOR vehicle |
| 10. Disconnect the RED (+) booster cable from the PREVIOUSLY DISABLED vehicle |
| 11. Disconnect the RED (+) booster cable from the battery of the DONOR vehicle |
CARRY OUT OPERATIONS IN SEQUENCE - PROCEDURE 2
| Carry out the following operations in the sequence given |
|---|
| 1. Make sure the customer has placed stolen vehicle tracking into Service Mode (if equipped). |
| 1. Connect one end of the RED (+) booster cable to the POSITIVE (+) battery terminal of the DONOR vehicle |
| 2. Connect the other end of the RED (+) booster cable to the POSITIVE (+) battery terminal of the DISABLED vehicle |
| 3. Connect one end of the BLACK (-) booster cable to the GROUND (-) battery terminal of the DONOR vehicle |
| 4. Connect the other end of the BLACK (-) booster cable to a good earth point (e.g. unpainted metal surface or engine mounting) at least 0.5 m from the battery or fuel lines on the DISABLED vehicle |
| 5. Start the engine of the DONOR vehicle and allow it to idle for a few minutes |
| 6. Start the engine of the DISABLED vehicle |
| 7. Allow the engines of both vehicles to idle for a few minutes, then switch off the engine of the DONOR vehicle |
| 8. Disconnect the BLACK (-) booster cable from the earth point of the PREVIOUSLY DISABLED vehicle |
| 9. Disconnect the BLACK (-) booster cable from the battery of the DONOR vehicle |
| 10. Disconnect the RED (+) booster cable from the PREVIOUSLY DISABLED vehicle |
| 11. Disconnect the RED (+) booster cable from the battery of the DONOR vehicle |
| 12. Request stolen vehicle tracking removed from Service Mode (if equipped). |
VEHICLE JUMP (EMERGENCY) STARTING - USING SLAVE BATTERY AND STARTING AID
| Vehicle status | Procedure |
|---|---|
| Vehicles without Telematics | 1 |
| Vehicles with Telematics | 2 |
CAUTION:
Ensure the clamping lug on the BMS is below the top of the negative terminal post as shown.
CARRY OUT OPERATIONS IN SEQUENCE - PROCEDURE 1
| Carry out the following operations in the sequence given |
|---|
| 1. Connect the end of the RED (+) booster cable to the POSITIVE (+) battery terminal of the vehicle |
| 2. Connect the end of the BLACK (-) booster cable to a good earth point (e.g. unpainted metal surface or engine mounting) at least 0.5 m from the battery or fuel lines on the vehicle |
| 3. Start the engine of the vehicle and allow it to idle |
| 4. Disconnect the BLACK (-) booster cable from the earth point of the vehicle |
| 5. Disconnect the RED (+) booster cable from the battery terminal of the vehicle. |
CARRY OUT OPERATIONS IN SEQUENCE - PROCEDURE 2
| Carry out the following operations in the sequence given |
|---|
| 1. Make sure the customer has placed stolen vehicle tracking into Service Mode (if equipped). |
| 2. Connect the end of the RED (+) booster cable to the POSITIVE (+) battery terminal of the vehicle |
| 3. Connect the end of the BLACK (-) booster cable to a good earth point (e.g. unpainted metal surface or engine mounting) at least 0.5 m from the battery or fuel lines on the vehicle |
| 4. Start the engine of the vehicle and allow it to idle |
| 5. Disconnect the BLACK (-) booster cable from the earth point of the vehicle |
| 6. Disconnect the RED (+) booster cable from the battery terminal of the vehicle. |
| 7. Request stolen vehicle tracking removed from Service Mode (if equipped). |