LEMON Manuals: Even more car manuals for everyone
Home >> Land Rover >> 2019 >> Range Rover Sport HST >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 44 (Engine - TDV6 3.0L Diesel Gen 1.5/TDV6 3.0L Diesel - Gen 2 -- Range Rover Sport/L494 (1 Of 2)) >> Engine - TDV6 3.0L Diesel/TDV6 3.0L Diesel - Gen 1.5/TDV6 3.0L Diesel - Gen 2 (G2094377) >> General Procedures >> Active Engine Mount - Vacuum Check (G2782711) >> Check

Active Engine Mount - Vacuum Check (G2782711): Check

WARNING: This page is about a different variant/trim than selected.
    • If the engine management lamp ON  , continue to step 1 of the repair article of this procedure.
    • If the engine management lamp is NOT ON  , continue to step 2.
  2. Raise and support the vehicle on a suitable 2 post lift.

    Refer to: JACKING AND LIFTING

  3. Open the hood.
  4. G14049328Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Remove the vac pipe active engine mount solenoid.

  5. G14049329Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Using the Jaguar Land Rover approved vacuum testing equipment, connect to the vacuum pipe and check that the active engine mounts hold vacuum. The engine mounts should generate a vacuum of 0.4 bar and then be able to hold the vacuum for 30 seconds.
    • If the active engine mount holds vacuum for 30 seconds, continue to step  1 of the repair article of this procedure.
    • If the active engine mounts does not hold vacuum for 30 seconds, continue to step 6.
  6. Remove the engine undershield. Refer to: ENGINE UNDERSHIELD
  7. NOTE: Check the vacuum pipe(s) and connections are tight and there are no signs of leakage.
    G14049330Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Disconnect the vacuum line directly from the right active engine mount.

  8. G11996439Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Inspect the right active engine mount switch positions.
    • If the right active engine mount switch clearly is not visible as shown in illustration E222279, continue to step 9.
    • If the right active engine mount switch is clearly visible as shown in illustration E222279, replace the right active engine mount and continue to step  11.

      Refer to: RIGHT ENGINE MOUNT 

  9. G14049332Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Using the Jaguar Land Rover approved vacuum testing equipment, connect to the right active engine mount and check that the active engine mount holds vacuum. The engine mount should generate a vacuum of 0.4 bar and then be able to hold the vacuum for 30 seconds.
    • If the right active engine mount holds vacuum for 30 seconds, continue to step 10.
    • If the right active engine mount does not hold vacuum for 30 seconds, replace the right active engine mount and continue to step  11.

      Refer to: RIGHT ENGINE MOUNT 

  10. NOTE: Check the vacuum pipe(s) and connections are tight and there are no signs of leakage.
    G14049330Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Reconnect the vacuum line directly from the right active engine mount.

  11. NOTE: Check the vacuum pipe(s) and connections are tight and there are no signs of leakage.
    G14049334Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Disconnect the vacuum line.
    • Connect the Jaguar Land Rover approved vacuum testing equipment to the left vacuum pipe.
    • Using the Jaguar Land Rover approved vacuum testing equipment, check that the left active engine mount holds vacuum. The engine mount should generate a vacuum of 0.4 bar and then be able to hold the vacuum for 30 seconds.
    • If the left active engine mount holds vacuum for 30 seconds, continue to step 12.
    • If the left active engine mount does not hold vacuum for 30 seconds, replace the left active engine mount and vacuum pipe and continue to step  13.

      Refer to: RIGHT ENGINE MOUNT 

  12. NOTE: Check the vacuum pipe(s) and connections are tight and there are no signs of leakage.
    G14049334Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Remove the Jaguar Land Rover approved vacuum testing equipment from the left vacuum pipe.
    • Reconnect the vacuum pipe.
    • Install the engine undershield.

      Refer to: ENGINE UNDERSHIELD

    • Lower the vehicle
    • The active engine mount vacuum check is complete and the active engine mounts have passed, continue to step  1 of the repair article of this procedure if fault is still persisting.
scientia non olet · About LEMON Manuals