LEMON Manuals: Even more car manuals for everyone
Home >> Land Rover >> 2019 >> Range Rover Sport HSE Dynamic >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 60 (Automatic Transmission/Transaxle - Vehicles With: 8HP76 8 - Speed Automatic Transmission AWD -- Range Rover Sport/L494) >> Automatic Transmission/Transaxle - Vehicles With: 8HP76 8-Speed Automatic Transmission, AWD (G2362076) >> General Procedures >> Automatic Transmission Fluid Drain and Refill (G2300924) >> Filling

Automatic Transmission Fluid Drain and Refill (G2300924): Filling

WARNING: This page is about a different variant/trim than selected.
  1. G11700446Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Fill the transmission with the recommended transmission fluid until fluid flows out of the filler hole.

    Refer to: SPECIFICATIONS 

  2. G11700447Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Allow the transmission fluid to drain from the transmission fluid filler hole until the flow stops.
    • Install the fluid filler plug, but only finger tight at this stage.
    • Remove the container under the vehicle to avoid damage.
  4. Make sure that the transmission is not in the default mode, if this is the case, stop and correct the cause first and then restart the fluid level check.
  5. CAUTION: Using the Jaguar Land Rover (JLR) approved diagnostic equipment, make sure the transmission temperature is between 30°C (85°F) and 50°C (122°F) before starting the automatic transmission fluid level check.
    • Connect the Jaguar Land Rover (JLR) approved diagnostic equipment to the vehicle.

      General Equipment:  Jaguar Land Rover approved diagnostic equipment

    • Start the engine and allow to idle.
    • Switch off the Air Conditioning (A/C) system and other electrical components.
  6. CAUTION: Make sure the automatic transmission fluid control system is filled with oil.
    • Apply and hold the brake pedal.
    • Select reverse gear and wait for 10 seconds.
    • Select drive, then manual 1st gear and wait for 10 seconds.
    • Select 2nd gear and wait for 10 seconds.
    • Select Park (P) on the Transmission Control Switch (TCS).
  7. NOTE: Make sure the torque converter is completely filled with oil.
    • Raise the engine speed to 2000 rpm and hold for 30 seconds. Then return to idle speed.
  8. NOTE: After completing the preparation, proceed to the automatic transmission fluid level check.
    • If the transmission oil temperature is lower than 30°C. Allow the transmission to warm up with the engine idling in the P position, then proceed with the transmission fluid level check.
    • If the transmission oil temperature is above 50°C, switch off the engine and allow the transmission to cool down, then restart the fluid level check.
  9. Switch the engine off.
  10. CAUTION: Make sure when checking the automatic transmission fluid level, that this procedure is followed. Failure to do so can cause damage to the vehicle.

    Check and top-up the transmission fluid level. Refer to: AUTOMATIC TRANSMISSION FLUID LEVEL CHECK 

  11. WARNING: This step is only required for 3.0L PETROL and 3.0L DIESEL vehicles
    G14067003Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Use a suitable tool to drain 350ml of transmission fluid from the automatic transmission filler hole.

  12. G11700448Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Install the transmission fluid filler plug.

    Special Tool(s): 307-452 

  13. CAUTION: Make sure the automatic transmission fluid fill plug is tightened to the correct specification. Failure to follow this instruction may result in damage to the transmission.
    G11700449Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • To make sure the transmission fill plug is torqued to the correct specification. Using the special tool and torque wrench the following calculation steps must be followed.
    • Step 1. Multiply 35 Nm by the effective length of the torque wrench (1).
    • Step 2. Add the effective length of the special tool (2) to the effective length of the torque wrench (1).
    • Step 3. Divide the total of step 1 by the total of step 2.
    • Step 4. Set the torque wrench to the figure arrived at in step 3.
    • Tighten the transmission fluid fill plug to the torque given by the calculation.
  14. G14067594Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Install the heatshield.
    • Install and tighten the 2 bolts.

      Torque  : 9 Nm 

  15. G12001150Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Install the transmission undershield.
    • Install and tighten the 10 bolts.

      Torque 

      M10: 60 Nm 

      M6: 10 Nm 

  16. Disconnect the Jaguar Land Rover (JLR) approved diagnostic equipment.

    General Equipment:  Jaguar Land Rover approved diagnostic equipment

scientia non olet · About LEMON Manuals