Engine - TDV6 3.0L Diesel (G2297235): Specifications
WARNING: This page is about a different variant/trim than selected.
ENGINE DATA
| ENGINE DESCRIPTION | ENGINE CAPACITY | MAXIMUM ENGINE TORQUE (EEC) (SAE) | MAXIMUM ENGINE POWER (EEC) (SAE) | COMPRESSION RATIO | BORE | STROKE |
|---|---|---|---|---|---|---|
| 60° "Vee" • 6 Cylinder • 24 Valves | 2993 ccm | 600 Nm at 2000 RPM | 202 kW at 4000 RPM | 16.1:1 ± 0.5 | 84 | 90 |
ENGINE FIRING ORDER
| FIRING ORDER |
|---|
| 1:4:2:5:3:6 |
GLOW PLUG
| SPECIFICATION |
|---|
| 9X2Q-6M090-AC |
LUBRICANTS, FLUIDS, SEALERS AND ADHESIVES
| DESCRIPTION | SPECIFICATION |
|---|---|
| Engine oil - Vehicles with diesel particulate filter | SAE 5W30 STJLR.03.5005 |
| Engine oil - Vehicles without diesel particulate filter | SAE 5W30 STJLR.03.5003 |
| Sealant | WSE-M4G323-A5 |
| Core plug and stub pipe retainer | WSK-M2G349-A7 |
| Jaguar premium cooling system fluid | WSS-M97B44-D |
CAPACITIES
| DESCRIPTION | LITERS |
|---|---|
| Engine oil and filter initial fill | 7.8 |
| Engine oil service fill with oil filter change | 7.0 |
CYLINDER HEAD AND VALVE TRAIN
| ITEM | SPECIFICATION |
|---|---|
| Valve guide inner diameter (mm) | 5.980 ± 0.010 |
| Intake valve effective length (mm) (tip to gauge line) | 94.99 mm +/- 0.15 |
| Exhaust valve effective length (mm) (tip to gauge line) | 94.45 mm +/-0.15 |
| Valve stem to guide clearance intake diametrical (mm) | 0.027 - 0.063 |
| Valve stem to guide clearance exhaust diametrical (mm) | 0.037 - 0.073 |
| Valve head diameter intake (mm) | 27.8 mm +/-0.1 |
| Valve head diameter exhaust (mm) | 25.2 mm +/-0.1 |
| Intake valve face angle (degrees) | 44 deg 52 min +/-7min30sec |
| Exhaust valve face angle (degrees) | 44 deg 52 min +/-7min30sec |
| Valve stem diameter intake (mm) | 5.935±0.008 |
| Valve stem diameter exhaust (mm) | 5.925±0.008 |
| Valve spring free length (mm) - inlet | 38.9 mm |
| Valve spring free length (mm) - exhaust | 38.9 mm |
| Valve spring installed height (mm) - inlet | 31.22 mm |
| Valve spring installed height (mm) - exhaust | 31.22 mm |
| Camshaft lobe max lift intake (mm) | 3.75187 mm |
| Camshaft lobe max lift exhaust (mm) | 3.80999 mm |
| Camshaft journal to cylinder head bearing surface clearance diametrical (mm) | 0.040-0.090 |
| Camshaft journal diameter - all positions | 25.950±0.010 |
| Bearing diameter - all positions | 26.015±0.015 |
| Camshaft journal maximum run out limit (mm) | 0.030 mm |
| Camshaft journal maximum out of round (mm) - all journals | 0.010 mm |
| Cylinder head maximum permitted warp (flatness specification) | 0.2 mm (0.008 in) |
| Cylinder block maximum permitted warp (flatness specification) | 0.15 mm (0.006 in) |
CYLINDER HEAD GASKET
| IDENTIFICATION | GASKET THICKNESS (MM) | PISTON PROTRUSION (MM) |
|---|---|---|
| 2 | 1.17 | 0.552 - 0.603 |
| 3 | 1.22 | 0.604 - 0.655 |
| 4 | 1.27 | 0.656 - 0.707 |
| 5 | 1.32 | 0.708 - 0.760 |
TORQUE SPECIFICATION
| DESCRIPTION | NM | LB-FT | LB-IN |
|---|---|---|---|
| Camshaft timing chain tensioner | 10 | 7 | 84 |
| Camshaft bearing cap | - | - | - |
| Stage 1 | 1 | 1 | 12 |
| Stage 2 | 5 | 4 | 48 |
| Stage 3 | 10 | 7 | 84 |
| Camshaft rear (READ) pulley hub bolt | - | - | - |
| Stage 1 | 80 | 59 | 708 |
| Stage 2 | 80° | - | - |
| Camshaft pulley bolts | 23 | 17 | 204 |
| Camshaft position sensor | 10 | 7 | 84 |
| Timing belt tensioner | - | - | - |
| Stage 1 | 20 | 15 | 180 |
| Stage 2 | 55° | - | - |
| Crankshaft vibration damper | 25 | 18 | 216 |
| Crankshaft pulley | - | - | - |
| Stage 1 | 150 | 111 | 1332 |
| Stage 2 | 300 | 221 | 2652 |
| Stage 3 | 90° | - | - |
| Crankshaft rear seal cover | 10 | 7 | 84 |
| Engine coolant temperature sensor | 14 | 10 | 120 |
| Oil temperature sensor | 14 | 10 | 120 |
| Cylinder head bolts | - | - | - |
| Stage 1 | 80 | 58 | 696 |
| Stage 2 | 180° | - | - |
| Engine mount nut and bolt | 60 | 44 | 528 |
| Exhaust manifold rear heat shield | 11 | 8 | 96 |
| Exhaust manifold front heat shield | 11 | 8 | 96 |
| Exhaust manifold sensor | 28 | 21 | 252 |
| Exhaust manifold nuts | 28 | 21 | 252 |
| Exhaust manifold cross over pipe nuts and bolts | 23 | 17 | 204 |
| Exhaust manifold cross over pipe stud | 13 | 10 | 120 |
| Drive plate | - | - | - |
| Stage 1 | 45 | 33 | 396 |
| Stage 2 | 90° | - | - |
| Oil cooler | 10 | 7 | 84 |
| Oil filter element | 27 | 20 | 240 |
| Oil level sensor | 10 | 7 | 84 |
| Oil strainer | 10 | 7 | 84 |
| Baffle plate | 10 | 7 | 84 |
| Oil pan M8 | - | - | - |
| Stage 1 | 4 | 3 | 36 |
| Stage 2 | 23 | 17 | 204 |
| Oil pan M6 | - | - | - |
| Stage 1 | 4 | 3 | 36 |
| Stage 2 | 10 | 7 | 84 |
| Valve cover bolts | 10 | 7 | 84 |
| Fuel rail bracket | 23 | 17 | 204 |