Water Leaks, Diagnosis And Corrective Action: Front Passenger Compartment

Windscreen 

• Diagnosis:
  • Ingress of water into A-pillar area or instrument cluster area and rocker panel area.
• Cause:
  • Breaks in adhesive beads
• Corrective action:
  • The breaks in adhesive beads can be located from inside by using compressed air. The leak can be identified from outside by the escaping air.
  • The second test method is by means of a water test. The outer trims must be raised carefully using a plastic wedge. The leak should be located from inside by a second assistant.

Side windows 

In the case of side windows, the same problems can arise as for a windscreen. The same corrective actions must therefore be used.

Door seal 

• Diagnosis:
  • Water ingress in the lower part of the interior door trim or in the rocker panel area.
• Cause:
  • The water shield fitted behind the interior door trim exists to drain off water that has entered the door via the drainage holes, either downwards or outwards. If the water shield seal is damaged or has been fitted incorrectly, then water can get into the passenger compartment.
  • In addition to this, the drainage holes can become clogged with leaves, dirt or excess cavity protection agents. Water gathers in the door and ingresses into the passenger compartment.
  • Check water shield for damage or correct fitting.
  • If the water shield needs to be re-bonded, then approved seam sealer should be used.
  • Before the water shield is installed, the drainage holes must be checked for unhindered flow.

Door seals 

• Diagnosis:
  • Ingress of water into the rocker panel area
• Cause:
  • Insufficient clamping load between seal and door.
• Corrective action:

  When adjusting the clamping load, the profile alignment of the relevant components must always be taken into consideration.

  Do not realign the flange too far in the direction of the door, as this can reduce the bearing surface of the seal to the door.

  • Check clamping load:
  • The easiest way to check the clamping load of a seal to the respective bearing surface is by means of a paper strip test. This consists of trapping strips of paper at various points between the door and the seal, and fully closing the door. If it is possible to pull out the paper with no great resistance, then the clamping load is too low.
  • Adjust the clamping load:
  • The clamping load is normally adjusted using the striker. When doing so, the edge alignment from the door to the side panel, or from the front door to the rear door must be taken into account.
  • Another setting method is to realign the panel flange for the seal mounting. The clamping load is increased by moving the flange towards the door.
  • Check the bearing surface:
  • Apply chalk evenly to the surface of the seal. Evenly coat the bearing surface of the door with Vaseline.
  • Close the door fully, the lock must engage. Open the door. The imprint of the chalk (bearing surface) can be identified in the film of Vaseline.
  • The bearing surface should be at least 5 mm across at all points.
• Other causes:
  • The door seal must completely seal the door where it meets the bodywork.
  • Water can ingress directly or indirectly into the interior of the vehicle if the seal is damaged at any point.
• Corrective action:
  • A damaged or worn door seal must always be renewed in full.
  • When renewing the seal, the following must be taken into account:
  • Always fit the seal first in the area of the narrow radii (corner points).
  • Next, secure the seal to the flange evenly by tapping lightly with a rubber hammer. The installed seal must not be kinked at any point.

• Other cause:
  • The door seal is attached to the welded flange all the way round. If this welded flange is uneven or damaged at any point (usually in areas with small radii) then this point could be subject to leaks.
  • A stretched seal carrier can also cause a leak.
  • In both cases, water gets into the vehicle interior under the seal carrier.
• Corrective action:
  • Align the deformed welded flange using a hammer and anvil block, prevent and, if necessary, repair any paint damage.

Sliding roof/tilting roof 

• Diagnosis:
  • Ingress of water at sliding roof aperture
• Cause:
  • The sliding roof/tilting roof is installed in a water trap. The water drains off via the water trap, water drain holes and drain hoses. The drain hoses lead downwards on both sides via the A-pillar and B-pillar.
  • The drain holes or drain hoses can become clogged with leaves, dirt, underbody protection and so on.
• Corrective action:

  In the case of a sliding or tilting roof, the external rubber seal and the lock actuator or latch mechanism must be checked first of all.

  • Check the water trap for leaks.
  • Check the drain hoses for leaks and for correct connection to the water trap.
  • Check the drainage system for unhindered flow, and blow out with compressed air if necessary.
  • Check the external seal and the correct adjustment of the sliding roof.

Tailgate 

• Diagnosis:
  • Ingress of water into rear headlining area and luggage area.
• Cause:
  • The leak problems of the tailgate and liftgate correspond to those of the doors.
  • In addition to this, the area to be sealed is much bigger. The routing holes for cables and hoses must also be sealed.
  • The rubber grommets for the routing holes must be checked for damage and correct seating (fully unhooked).
  • The mounting points of the liftgate hinges may leak.
• Corrective action:
  • Check the rubber grommets and renew if necessary.
  • Check the hinge mounting points, and re-seal with sealing compound if necessary.

Forced air extraction 

• Diagnosis:
  • Ingress of water into side luggage compartment area
• Cause:
  • The forced air extraction for the vehicle interior is located in the quarter panel lower extension.
  • The rubber flap of the forced air extraction must be able to move freely.
• Corrective action:
  • Remove the forced air extraction.
  • Check the seal area between the bodywork and housing, as well as the rubber flap.
  • Renew seal if necessary.

Rear window 

• Diagnosis:
  • Ingress of water into the luggage compartment area
• Cause:
  • Rear window leaking.
  • Check for leak in the same way as for leaking windscreen.