Suspension System - General Information: Specifications
AIR SPRING SUSPENSION SPECIFICATION
| ITEM | SPECIFICATION | ||
|---|---|---|---|
| Type - Front | Independent double wishbone suspension with air springs, mono tube dampers, height sensors and stabilizer bar. Driver selectable ride heights - Standard, off road and access. | ||
| Type - Rear | Independent suspension with air springs, mono tube dampers, height sensors and either a conventional or dynamic response stabilizer bar depending on vehicle specification. Driver selectable ride heights - Standard, off road and access | ||
| (1)Nominal heights from hub center to underside of wheel arch (not liner): | |||
| Front | 471 mm (18.54 in) | ||
| Rear | 468 mm (18.43 in) | ||
|
|||
NOTE:
All figures are with vehicle at 'Showroom' ride height - full fluids, full tank of fuel, no occupants/luggage, tires inflated to normal pressures
WHEEL ALIGNMENT SPECIFICATION - FRONT
| ITEM | LEFT-HAND | RIGHT-HAND | TOTAL/BALANCE | ||||
|---|---|---|---|---|---|---|---|
| Camber | Nominal | Tolerance | Nominal | Tolerance | Nominal | Tolerance | |
| Decimal degrees | -0.68° | ± 0.75° | -0.68° | ± 0.75° | 0° | ± 0.75° | |
| Degrees/minutes | -41' | ± 45' | -41' | ±45' | 0' | ± 45' | |
| Minimum | Maximum | Minimum | Maximum | Minimum | Maximum | ||
| Decimal degrees | -1.43° | 0.07° | -1.43° | 0.07 | -0.75° | 0.75° | |
| Degrees/minutes | -1°26' | 4' | -1°26 | 4' | -45' | -45' | |
| Castor | Nominal | Tolerance | Nominal | Tolerance | Nominal | Tolerance | |
| Decimal degrees | 4.12° | ± 0.75° | 4.12° ± | 0.75° | 0° | ± 0.75° | |
| Degrees/minutes | 4.7' | ± 45' | 4°7' | ± 45' | 0' | ± 45' | |
| Minimum | Maximum | Minimum | Maximum | Minimum | Maximum | ||
| Decimal degrees | 3.75° | 4.87° | 3.75° | 4.87° | -0.75° | 0.75° | |
| Degrees/minutes | 3°22' | 4°52' | 3°22' | 4°52' | -45' | 45' | |
| Toe | Nominal | Tolerance | Nominal | Tolerance | Nominal | Tolerance | |
| Decimal degrees | 0.07° | ± 0.10° | 0.07° ± | 0.10° | 0.14° | ±0.20° | |
| Degrees/minutes | 4' | ± 6' | 4' | ± 6' | 8' | ±12' | |
| Minimum | Maximum | Minimum | Maximum | Minimum | Maximum | ||
| Decimal degrees | -0.03° | 0.17° | -0.03° | 0.17 | -0.06° | 0.34° | |
| Degrees/minutes | -2' | 10' | -2' | 10' | -4' | 20' | |
NOTE:
All figures are with vehicle at 'Showroom' ride height - full fluids, full tank of fuel, no occupants/luggage, tires inflated to normal pressures
WHEEL ALIGNMENT SPECIFICATION - REAR
| ITEM | LEFT-HAND | RIGHT-HAND | TOTAL/BALANCE | THRUST ANGLE | |||||
|---|---|---|---|---|---|---|---|---|---|
| Camber | Nominal | Tolerance | Nominal | Tolerance | |||||
| Decimal degrees | -1.42° | ± | 0.75° | -1.42° | ± 0.75° | ||||
| Degrees/minutes | -1°-25' | ± | 45' | -1°-25' | ± 45' | ||||
| Minimum | Maximum | Minimum | Maximum | ||||||
| Decimal degrees | -2.17° | -0.67° | -2.17° | -0.67° | |||||
| Degrees/minutes | -2°10' | -40' | -2°10' | -40' | |||||
| Toe | Nominal | Tolerance | Nominal | Tolerance | Nominal | Tolerance | Nominal | Tolerance | |
| Decimal degrees | 0.15° | ±0.14° | 0.15° | ±0.14° | 0.30° | ±0.20° | 0° | ±0.14° | |
| Degrees/minutes | 9' | ±8' | 9' | ±8' | 18' | ±12' | 0' | ±8' | |
| Minimum | Maximum | Minimum | Maximum | Minimum | Maximum | Minimum | Maximum | ||
| Decimal degrees | 0.01° | 0.29° | 0.01° | 0.29° | 0.10° | 0.50° | -0.14° | 0.14° | |
| Degrees/minutes | 1' | 17' | 1' | 17' | 6' | 30' | -8' | 8' | |