Engine - TDV6 3.0L Diesel - Gen 2/TDV6 3.0L Diesel: Specifications
WARNING: This page is about a different variant/trim than selected.
ENGINE DATA - LOW FLOW FUEL INJECTION SYSTEM
| ENGINE DESCRIPTION | ENGINE CAPACITY | MAXIMUM ENGINE TORQUE (EEC) (SAE) | MAXIMUM ENGINE POWER (EEC) (SAE) | COMPRESSION RATIO | BORE | STROKE |
|---|---|---|---|---|---|---|
| 60° "Vee" • 6 Cylinder • 24 Valves | 2993 ccm | 600 Nm at 2000 RPM | 190 kW at 4000 RPM | 16.1:1 ± 0.5 | 84 | 90 |
ENGINE DATA - STANDARD FLOW FUEL INJECTION SYSTEM
| ENGINE DESCRIPTION | ENGINE CAPACITY | MAXIMUM ENGINE TORQUE (EEC) (SAE) | MAXIMUM ENGINE POWER (EEC) (SAE) | COMPRESSION RATIO | BORE | STROKE |
|---|---|---|---|---|---|---|
| 60° "Vee" • 6 Cylinder • 24 Valves | 2993 ccm | 600 Nm at 2000 RPM | 223 kW at 4000 RPM | 16.1:1 ± 0.5 | 84 | 90 |
ENGINE FIRING ORDER
| FIRING ORDER |
|---|
| 1:4:2:5:3:6 |
GLOW PLUG
| SPECIFICATION |
|---|
| 9X2Q-6M090-AC |
LUBRICANTS, FLUIDS, SEALERS AND ADHESIVES
| DESCRIPTION | SPECIFICATION |
|---|---|
| Engine oil - Vehicles with diesel particulate filter | SAE 5W30 STJLR.03.5005 |
| Engine oil - Vehicles without diesel particulate filter | SAE 5W30 STJLR.03.5003 |
| Sealant | WSE-M4G323-A5 |
| Core plug and stub pipe retainer | WSK-M2G349-A7 |
| Cooling system fluid | Havoline Extended Life Coolant (XLC) |
CAPACITIES
| DESCRIPTION | LITERS |
|---|---|
| Engine oil initial fill | 6.66 |
| Engine oil service fill with oil filter change | 6.0 |
CYLINDER HEAD AND VALVE TRAIN
| ITEM | SPECIFICATION |
|---|---|
| Valve guide inner diameter (mm) | 5.980 ± 0.010 |
| Intake valve effective length (mm) (tip to gauge line) | 94.99mm +/- 0.15 |
| Exhaust valve effective length (mm) (tip to gauge line) | 94.45mm +/-0.15 |
| Valve stem to guide clearance intake diametrical (mm) | 0.027 - 0.063 |
| Valve stem to guide clearance exhaust diametrical (mm) | 0.037 - 0.073 |
| Valve head diameter intake (mm) | 27.8mm +/-0.1 |
| Valve head diameter exhaust (mm) | 25.2mm +/-0.1 |
| Intake valve face angle (degrees) | 44 deg 52 min +/- 7min30sec |
| Exhaust valve face angle (degrees) | 44 deg 52 min +/- 7min30sec |
| Valve stem diameter intake (mm) | 5.935±0.008 |
| Valve stem diameter exhaust (mm) | 5.925±0.008 |
| Valve spring free length (mm) - inlet | 38.9mm |
| Valve spring free length (mm) - exhaust | 38.9mm |
| Valve spring installed height (mm) - inlet | 31.22mm |
| Valve spring installed height (mm) - exhaust | 31.22mm |
| Camshaft lobe max lift intake (mm) | 3.75187mm |
| Camshaft lobe max lift exhaust (mm) | 3.80999mm |
| Camshaft journal to cylinder head bearing surface clearance diametrical (mm) | 0.040-0.090 |
| Camshaft journal diameter - all positions | 26.015±0.015 |
| Bearing diameter - all positions | 25.950±0.010 |
| Camshaft journal maximum run out limit (mm) | 0.030mm |
| Camshaft journal maximum out of round (mm) - all journals | 0.010mm |
| Cylinder head maximum permitted warp (mm) flatness specification | 0.2mm (0.008 in) |
CYLINDER HEAD GASKET
| IDENTIFICATION | GASKET THICKNESS (MM) | PISTON PROTRUSION (MM) |
|---|---|---|
| 2 | 1.17 | 0.552 - 0.603 |
| 3 | 1.22 | 0.604 - 0.655 |
| 4 | 1.27 | 0.656 - 0.707 |
| 5 | 1.32 | 0.708 - 0.760 |
NOTE:
A = refer to procedure for correct torque sequence
TORQUE SPECIFICATION
| DESCRIPTION | NM | LB-FT | LB-IN |
|---|---|---|---|
| Piston cooling nozzle | 10 | 7 | - |
| Engine coolant drain plug | 18 | 13 | - |
| Cylinder head retaining bolts | A** | - | - |
| Oil filter housing retaining bolts | 10 | 7 | - |
| Fuel injection pump cradle retaining bolts | 23 | 17 | - |
| Fuel injection pump to cradle retaining bolts | 23 | 17 | - |
| Fuel injection pump bracket to cradle retaining bolts | 10 | 7 | - |
| Fuel injection pump to bracket retaining bolts | 10 | 7 | - |
| Oil pump retaining bolts | 10 | 7 | - |
| Crankshaft rear oil seal housing retaining bolts | 10 | 7 | - |
| Oil pan retaining bolts M6 | 10 | 7 | - |
| Oil pan retaining bolts M8 | 23 | 17 | - |
| Oil pump pick up pipe retaining bolts | 10 | 7 | - |
| Engine oil level sensor retaining nuts | 10 | 7 | - |
| Crankshaft timing belt pulley retaining bolt | A** | - | - |
| Crankshaft position sensor (CKP) retaining bolt | 5 | - | 44 |
| Timing chain tensioner retaining bolts | 10 | 7 | - |
| Camshaft bearing cap retaining bolts | A** | - | - |
| Timing belt idler pulley retaining bolt | 45 | 33 | - |
| Fuel injection pump belt rear cover retaining bolts | 10 | 7 | - |
| Fuel injection pump sprocket retaining nut | 50 | 37 | - |
| Coolant outlet pipe retaining bolts | 10 | 7 | - |
| Coolant pump retaining bolts | 10 | 7 | - |
| Timing belt tensioner retaining bolt | 26 | 19 | - |
| Engine lifting eye bolts | 23 | 17 | - |
| Camshaft rear end accessory drive (READ) pulley hub retaining bolt | Stage 1 - 80 Stage 2 - 80 degrees | Stage 1 - 59 Stage 2 - 80 degrees | - |
| Camshaft front timing pulley hub retaining bolt | 80 + 80° | 59 + 80 ° | - |
| Camshaft READ pulley retaining bolt | 23 | 17 | - |
| Camshaft front timing pulley retaining bolt | 23 | 17 | - |
| Fuel injection pump timing belt tensioner bolt | 23 | 17 | - |
| Camshaft position sensor (CMP) retaining bolt | 10 | 7 | - |
| Intake manifold/camshaft cover retaining bolts | 10 | 7 | - |
| Brake vacuum pump retaining bolts | 23 | 17 | - |
| Engine oil pressure (EOP) switch | 14 | 10 | - |
| Glow plug | 11 | 8 | - |
| Fuel rail retaining bolts | 23 | 17 | - |
| Fuel rail bracket retaining bolts | 23 | 17 | - |
| Fuel injector retaining bolts | A** | - | - |
| High pressure fuel line union nuts | A** | - | - |
| High pressure fuel line bracket retaining bolts | 9 | - | 80 |
| Turbocharger assembly to exhaust manifold retaining nuts | 24 | 18 | - |
| Exhaust manifold to cylinder head retaining nuts | A** | - | - |
| Exhaust manifold heatshield retaining bolts | 11 | 8 | - |
| Turbocharger heatshield retaining bolts | 11 | 8 | - |
| Exhaust gas recirculation (EGR) valve retaining bolts M6 | 10 | 7 | - |
| Accessory drive belt idler pulley bracket retaining bolts | 83 | 61 | - |
| Timing belt covers retaining bolts | 10 | 7 | - |
| Engine mount bracket to engine retaining bolts | 115 | 85 | - |
| Engine mount bracket to engine mounting | 130 | 96 | - |
| Engine mounting to subframe bolts. | A** | - | - |
| Exhaust cross over pipe retaining nuts | 24 | 18 | - |
| Engine coolant inlet pipe retaining bolts | 10 | 7 | - |
| Coolant pump pulley retaining bolts | 25 | 18 | - |
| Crankshaft pulley/vibration damper retaining bolts | 25 | 18 | - |
| Throttle body retaining threaded stud | 10 | 7 | - |
| Wiring harness retaining nuts | 10 | 7 | - |
| Vacuum hose assembly retaining bolts | 10 | 7 | - |
| Flexplate retaining bolts | A** | - | - |
| Accessory drive component bracket retaining bolts | 23 | 17 | - |
| Generator retanining bolts | 47 | 35 | - |
| Accessory drive belt tensioner retaining bolt | 47 | 35 | - |
| Accessory drive belt idler pulley retaining bolt | 47 | 35 | - |
| Air conditioning compressor bracket retaining bolts | 23 | 17 | - |
| Air conditioning compressor retaining bolts | 23 | 17 | - |