DTC U0080-87: Vehicle Communication Bus F - Missing message: Action
WARNING: This page is about a different variant/trim than selected.
- The responses from DID 0xD020 and possible causes for this DTC are as follows
- Response 0xC95
- Check ALCM fuses and try to establish diagnostic communication with the ALCM
- Check FlexRay bus
- Check CAN connection to GWM
- Response 0x0D6
- Check ATCM fuses and try to establish diagnostic communication with the ATCM
- Check FlexRay bus
- Check CAN connection to GWM
- Response 0xE4A
- Check ATCM3 fuses and try to establish diagnostic communication with the ATCM3
- Check FlexRay bus
- Check CAN connection to GWM
- Response 0xA09
- Check AWD fuses and try to establish diagnostic communication with the AWD
- Check FlexRay bus
- Check CAN connection to GWM
- Response 0x79E
- Check CJB fuses and try to establish diagnostic communication with the CJB
- Check FlexRay bus
- Check CAN connection to GWM
- Response 0x729
- Check CCM fuses and try to establish diagnostic communication with the CCM
- Check FlexRay bus
- Check CAN connection to GWM
- Response 0x120
- Check CHCM fuses and try to establish diagnostic communication with the CHCM
- Check FlexRay bus
- Check CAN connection to GWM
- Response 0x0F9
- Check CHCMB fuses and try to establish diagnostic communication with the CHCMB
- Check FlexRay bus
- Check CAN connection to GWM
- Response 0x995
- Check FACP fuses and try to establish diagnostic communication with the FACP
- Check FlexRay bus
- Check CAN connection to GWM
- Response Ox12AE
- Check Touch Screen fuses and try to establish diagnostic communication with the Touch Screen
- Check FlexRay bus
- Check CAN connection to GWM
- Response 0x25F
- Check GSM fuses and try to establish diagnostic communication with the module
- Check FlexRay bus
- Check CAN connection to GWM
- Response 0x024
- Check GWM fuses and try to establish diagnostic communication with the module
- Check FlexRay bus
- Response 0x0E3
- Check automatic temperature control module fuses and try to establish diagnostic communication with the module
- Check FlexRay bus
- Check CAN connection to GWM
- Response 0x76C
- Check IPC fuses and try to establish diagnostic communication with the module
- Check FlexRay bus
- Check CAN connection to GWM
- Response Ox119E
- Check image processing control module fuses and try to establish diagnostic communication with the module
- Check FlexRay bus
- Check CAN connection to GWM
- Response 0x38B
- Check parking assist control module fuses and try to establish diagnostic communication with the module
- Check FlexRay bus
- Check CAN connection to GWM
- Response 0x256
- Check electric park brake control module fuses and try to establish diagnostic communication with the module
- Check FlexRay bus
- Check CAN connection to GWM
- Response 0x247
- Check power steering control module fuses and try to establish diagnostic communication with the module
- Check FlexRay bus
- Check CAN connection to GWM
- Response 0xlE3
- If combined with B10A2-32, check restraints control module fuse/communication and crash interface circuit
- If combined with U0151-08 and U0151-00 and B10A2-32 and U0405-84 and possibly with B1142-62 in the GSM, check for the ignition sense line high when the PowerMode_HS is less than 6 (ignition high when the vehicle has been switched off)
- Check CAN connection to GWM
- Response 0x499
- Check SASM fuses and try to establish diagnostic communication with the module
- Check FlexRay bus
- Check CAN connection to GWM
- Response 0xl9F
- Check TCCM fuses and try to establish diagnostic communication with the module
- Check FlexRay bus
- Response 0x040
- Check ABS fuses and try to establish diagnostic communication with the ABS
- Check FlexRay bus