Removal And Installation: Installation

WARNING: This page is about a different car, the 2018 Land Rover Range Rover, 2017 Land Rover Range Rover, and 2016 Land Rover Range Rover. However, it is still accessible from the selected car via links, so may be relevant.

Special Tool(s): 310-139A

Torque Specification: 50 Nm
Torque Specification: 3 Nm
Torque Specification: 23 Nm
Torque Specification: 10 Nm
CAUTION: Apply loctite 242 to the new camshaft pulley bolt.
Special Tool(s): JLR-303-1523

Torque Specification: 10 Nm
Special Tool(s): JLR-303-1523
CAUTION: Make sure the torque wrench setting procedure is followed correctly. Failure to follow this instruction may result in damage to the vehicle.
- Calculate the setting for the torque wrench:
- Stage 1: Multiply the required torque by the effective length of the torque wrench (1).
- Stage 2: Add the effective length of the special tool (2) to the effective length of the torque wrench.
- Stage 3: Divide the total of stage 1 by the total of stage 2.
- Stage 4: Set the torque wrench to the figure arrived at in stage 3.
CAUTION: Make sure the torque wrench setting procedure is followed correctly. Failure to follow this instruction may result in damage to the vehicle.

Special Tool(s): 303-1145/2

Torque Specifications:

Stage 1: 80 Nm

Stage 2: 80°
Remove the special tools.
NOTE: If equipped.

Torque Specification: 10 Nm
NOTE: If equipped.

Torque Specification: 10 Nm
NOTE: Fuel injection pump pulley shown removed for clarity.

Torque Specification: 10 Nm
NOTE: Fuel injection pump pulley shown removed for clarity.

Torque Specification: 23 Nm
CAUTION: Tighten the fuel supply line unions finger tight.

Renew Part: Fuel rail LH supply pipe Quantity: 1 .

Renew Part: Fuel rail RH supply pipe Quantity: 1 .
CAUTION: Tighten the fuel supply line unions finger tight.

NOTE: Some variation in the illustrations may occur, but the essential information is always correct.
CAUTION: Tighten the fuel supply line unions finger tight.

NOTE: Some variation in the illustrations may occur, but the essential information is always correct.
CAUTION: Make sure that a new component is installed.

Renew Part: Fuel rail balance pipe Quantity: 1 .
CAUTION: Tighten the fuel supply line unions finger tight.

Renew Part: Fuel rail supply pipe(s) Quantity: 1 .
Torque Specification: 10 Nm
Tighten the high-pressure fuel lines union to 15Nm.
NOTE: Some variation in the illustrations may occur, but the essential information is always correct.

Tighten the high-pressure fuel lines union to 15Nm.
NOTE: Some variation in the illustrations may occur, but the essential information is always correct.

Tighten the high-pressure fuel line union to 15 Nm.
Tighten the high-pressure fuel lines union to 15Nm.
Tighten the high-pressure fuel lines union to 15Nm.
Tighten the high-pressure fuel line union to 35 Nm.
NOTE: Some variation in the illustrations may occur, but the essential information is always correct.

Tighten the high-pressure fuel line union to 35 Nm.
NOTE: Some variation in the illustrations may occur, but the essential information is always correct.

Tighten the high-pressure fuel line union to 35 Nm.
Tighten the high-pressure fuel line union to 35 Nm.
Tighten the high-pressure fuel line union to 35 Nm.
Torque Specification: 10 Nm
Refer to: CRANKCASE VENT OIL SEPARATOR
Refer to: REAR END ACCESSORY DRIVE
Refer to: HIGH-PRESSURE FUEL SYSTEM BLEEDING